“MP5” Surface Mount Crystals

“MP5”
MERCURY
Surface Mount Crystals
Since 1973
• MP5 surface mount crystals feature metal can low profile
crystal mounted on a plastic molded lead frame base.
• Available in EIA-481A-2 24 mm tape and reel. 1000 pcs per reel.
SPECIFICATIONS
Crystal Holder Prefix:
MP5 (5.25 mm height)
3.5 ~ 30.0 MHz AT-cut Fundamental mode
Mode of Oscillation:
30.1 ~ 70.0 MHz AT-cut 3rd Overtone mode
25.0 ~ 40.0 MHz BT-cut Fundamental mode
Calibration Tolerance:
Frequency Stability:
Shunt Capacitance (Co):
Equivalent
Series
Resistance
(E.S.R.)
±30ppm (±0.003 %) at 25°C
AT-cut: ±30 ppm (±0.003 %) over –10 to +60°C
BT-cut: ±100 ppm (±0.01 %) over -10 to +60°C
7 pF maximum
Frequency
Osc. Mode
ESR max.
Frequency
Osc. mode
ESR max.
3.20 ~ 3.56
AT funda.
200 Ω
9.0 ~ 12.99
AT funda.
60 Ω
3.57 ~ 3.99
AT funda.
180 Ω
13.0 ~ 15.99
AT funda.
50 Ω
4.0 ~ 4.99
AT funda.
150 Ω
16.0 ~ 30.00
AT funda.
40 Ω
5.0 ~ 5.99
AT funda.
120 Ω
27.0 ~ 40.00
BT funda.
40 Ω
6.0 ~ 6.99
AT funda.
100 Ω
30.0 ~ 70.00
AT 3rd O/T
100 Ω
7.0 ~ 8.99
AT funda.
80 Ω
Load Capacitance (CL):
Drive Level:
Aging:
Reflow Soldering:
Storage Temperature:
Series (S) or
Parallel (If parallel, please specify CL value, typical CL ranges from 8 to 32pF)
0.5 mW maximum
Less than ±5ppm per year. at +25°C.
10 seconds maximum at +260°C
-30 to +85°C
Note: Tighter tolerance, tighter stability and lower ESR are available.
MERCURY
www.mercury-crystal.com
Taiwan: TEL (886)-2-2695-7099, FAX (886)-2-2695-7473, e-mail: [email protected]
U.S.A.: TEL (1)-909-466-0427, FAX (1)-909-466-0762, e-mail: [email protected]
MERCURY
Page 1 of 2
Date: Jan. 3, 2005
Rev. 1
“MP5”
MERCURY
Surface Mount Crystals
Since 1973
STANDARD FREQUENCIES AND PART NUMBERS (partial frequency list only. Frequency tolerance,
frequency stability and ESR can be specified per your requirements).
MEC Part Number
MP5-3.579545-18P
MP5-3.6864-20P
MP5-4.000-20P
MP5-4.032-20P
MP5-4.096-20P
MP5-4.433619-18P
MP5-4.9152-18P
MP5-5.0688-18P
MP5-6.000-18P
MP5-6.144-18P
MP5-7.3728-18P
MP5-8.000-18P
MP5-9.8304-20P
MP5-11.0592-20P
MP5-12.000-18P
MP5-14.31818-18P
MP5-14.7456-S
MEC Specification Code
50/50/-10+70/200R
50/50/-10+70/200R
50/50/-10+70/150R
50/50/-10+70/150R
50/50/-10+70/150R
50/50/-10+70/150R
50/50/-10+70/150R
50/50/-10+70/150R
50/50/-10+70/100R
50/50/-10+70/100R
50/50/-10+70/100R
50/50/-10+70/100R
50/50/-10+70/100R
50/50/-10+70/80R
50/50/-10+70/80R
50/50/-10+70/50R
50/50/-10+70/50R
MEC Part Number
MP5-16.000312-32P
MP5-18.432-S
MP5-19.6608-S
MP5-20.000-20P
MP5-24.000-S
MP5-24.576-S
MP5-29.4912AF-S
MP5-30.000A3-S
MP5-30.000A3-S
MP5-32.000A3-S
MP5-36.000A3-S
MP5-40.000A3-S
MP5-29.4912BF-S
MP5-30.000BF-S
MP5-36.000BF-S
MP5-40.000BF-S
MEC Specification Code
50/50/-10+70/50R
50/50/-10+70/50R
50/50/-10+70/50R
50/50/-10+70/50R
50/50/-10+70/50R
50/50/-10+70/50R
50/50/-10+70/50R (AT-cut Fund.)
50/50/-10+70/140R (AT-cut 3rd O/T)
50/50/-10+70/140R (AT-cut 3rd O/T)
50/50/-10+70/140R (AT-cut 3rd O/T)
50/50/-10+70/100R (AT-cut 3rd O/T)
50/50/-10+70/100R (AT-cut 3rd O/T)
50/100/-10+70/50R (BT-cut Funda.)
50/100/-10+70/40R (BT-cut Funda.)
50/100/-10+70/40R (BT-cut Funda.)
50/100/-10+70/40R (BT-cut Funda.)
PACKAGE DIMENSIONS AND SUGGESTED PAD LAYOUT
[0.145]
3.68
MP5
M E C
[0.006]
0.15
5.25
[0.207 max]
10.26 [0.403]
12.0 [0.472]
[0.177]
4.5
Unit: mm [inches]
9.4 [0.370]
MERCURY
1.80 [0.071]
1.90 [0.075]
[0.047]
1.20
2.10
[0.083]
0.8 [0.031]
Page 2 of 2
1.70 [0.067]
1.2 [0.047]
7.60
[0.299]
Date: Jan. 3, 2005
Rev. 1