FLAT WIRE HIGH CURRENT INDUCTOR H2104 SERIES • High Current Inductors (inductance range from 12μH to 91μH) in a compact size package (44.5mm x 37mm x 26mm) • Flat wire coil minimizes losses at high frequency • Vertical and horizontal mount versions available (add -V or -H after part number for mounting version) • Operating Temperature -40ºC to +150ºC • RoHS Compliant Product • Custom Design Available ELECTRICAL PARAMETERS @ 25°C Part Number H2104-130 Isat INDUCTANCE (μH) DCR (mΩ) ±15% MAX 10% drop 20% drop 12.7 3.0 116 174 Irms (A) Typ Dim A (mm) Dim B (mm) 30% drop 40ºC rise MAX REF 228 48 26.0 13.0 (A) Typ H2104-200 19.6 3.0 58 82 102 48 26.0 13.0 H2104-230 22.5 5.0 87 130 171 37 26.0 13.5 H2104-240 24.3 4.5 87 134 177 42 33.0 20.5 H2104-290 29.4 3.0 31 47 61 48 26.0 13.0 H2104-350 34.8 5.0 43 61 77 37 26.0 13.5 H2104-370 37.3 4.5 45 64 81 42 33.0 20.5 H2104-400 39.7 7.1 68 105 139 33 33.0 20.0 H2104-520 52.2 5.0 23 35 45 37 26.0 13.5 H2104-560 55.7 4.5 25 37 48 42 33.0 20.5 H2104-610 60.8 7.1 35 50 63 33 33.0 20.0 H2104-910 91.0 7.1 19 29 37 33 33.0 20.0 Note: 1. Inductance measured at 10KHz, 1Vrms 2. Isat is DC current at which the inductance drops the specified amount from its original value without bias. 3. Irms is the DC current that causes the specified temperature rise of the winding from 25°C ambient for the inductor. Product performance is limited to specified parameters. Data is subject to change without prior notice. Tel: 310-325-1043 Fax: 310-325-1044 Dimensions Unless otherwise specified, all tolerances are: inch: .XX : ±0.015 .XXX : ±0.004 mm: X,X : ±0,38 X,XX : ±0,10 www.mpsind.com [email protected] FLAT WIRE HIGH CURRENT INDUCTOR H2104 SERIES DIMENSIONS (inch / [mm]) VERTICAL MOUNT HORIZONTAL MOUNT 1.75 Max [44,5] 1.46 Max [37,0] 1.75 Max [44,5] A MPS H2104-XXX-V Date Code 1.46 Max [37,0] MPS H2104-XXX-H Date Code Recommended PCB Layout 0.08 [2,0] 0.20 Ref [5,0] 0.03 Min [0,8] 0.27 Typ [7,0] 0.98 Ref [25,0] 0.27 Typ [7,0] 0.98 Ref [25,0] 0.98 [25,0] 0.31 [8,0] B A 0.20 Ref [5,0] Product performance is limited to specified parameters. Data is subject to change without prior notice. Tel: 310-325-1043 Fax: 310-325-1044 0.03 Min [0,80] Dimensions Unless otherwise specified, all tolerances are: inch: .XX : ±0.015 .XXX : ±0.004 mm: X,X : ±0,38 X,XX : ±0,10 www.mpsind.com [email protected]