HAND CRIMP TOOL Z22-020 Z22-020 24-30 M22-305 28-30 M22-308 24-26 M22-308 5 This Hand Crimp Tool has been designed for use with the following crimp contacts: M22-30400XX .................................. 2mm Pitch Crimp Contacts, Reeled, Gold or Tin M22-30500XX .................................. 2mm Pitch Crimp Contacts, Loose, Gold or Tin M22-3060046 .................................. 2mm Pitch Crimp Contacts, Reeled, Tin M22-3080046 .................................. 2mm Pitch Crimp Contacts, Loose, Tin Harwin North America Harwin Europe Harwin Asia T: +1 603 893 5376 F: +1 603 893 5396 E: [email protected] W: www.harwin.com T: +44 (0) 23 9231 4545 F: +44 (0) 23 9231 4590 E: [email protected] W: www.harwin.com T: +65 6 779 4909 F: +65 6 779 3868 E: [email protected] W: www.harwin.com.sg IS-05 Issue: 5 Date: 15.06.12 C/Note: 11756 Page 1 of 4 GENERAL INFORMATION The Z22-020 Hand Crimp Tool consists of a ratchet mechanism hand tool and a set of jaws. The jaws comprise of upper and lower crimp dies. The contact is correctly crimped when the tool is free to open at the fully closed position, i.e. when the ratchet releases. CRIMPING PROCEDURE 1. Ensure that the wire to be crimped is within the specified range of sizes for the contact and the crimp tool. Failure to use the specified wire size will result in poor quality crimps and possible tool damage. Wire Gauge 30 AWG 28 AWG 26 AWG 24 AWG 2. Minimum pull-off force (Newtons) 6N 11N 18N 29N Strip the wire insulation to the dimensions shown below. Care should be taken to avoid cutting or displacing the conductors. If the conductors are displaced, they may be re-aligned with a gentle twist. 1.0 – 1.5mm (M22-304/5) 1.5 – 2.0mm (M22-306/8) Ø1.4mm max 3. Make certain that the hand crimp tool is in the fully open position, and that the jaws are free from dirt and debris. 4. If the socket is on a reel, break or cut off a contact from the strip of bandolier. 5. Place the contact into the correct crimp cavity in the fixed jaw. The markings on the jaw indicate the correct crimp cavity according to the wire size being used. The orientation of the contact is with the crimp end uppermost, with the open side of the crimp facing towards the moving jaw. 6. Partially close the crimp tool until the wire stop comes across the face of the fixed jaw. 7. Take the pre-stripped wire and insert it into the contact so the conductors and insulation are positioned in the crimp. The conductors should be touching the wire stop. 8. Keeping the cable steady in the crimp, fully close the hand crimp tool until the ratchet releases. Let the crimp tool open. 9. After crimping remove the assembly. The process is then repeated for each crimp required. IS-05 Issue: 5 Date: 15.06.12 C/Note: 11756 Page 2 of 4 RECOMMENDED CRIMP HEIGHTS M22-30400XX and M22-30500XX: Using 24 – 30AWG wire, recommended conductor crimp height = 0.59±0.03mm M22-30600XX and M22-30800XX: Using 24 – 26AWG wire, recommended conductor crimp height = 0.70±0.03mm Using 28 – 30AWG wire, recommended conductor crimp height = 0.62±0.03mm TOOL MAINTENANCE 1. Keep the tool clean and free from dirt and foreign matter. Ensure that all retaining pins and clips are in place before use, and that signs of wear are not visible. If the pivots are worn, the tool must be replaced, or crimp integrity will be compromised. 2. Oil at all pivots and bearings using light cycle oil. 3. At regular intervals, check the crimp tool jaws for wear or damage, and inspect sample crimps for form and function. Minimum pull-off forces (as shown in the previous table) should be achieved when sample is tested. If forces are not achieved, calibrate the tool. TOOL CALIBRATION The operating force at the point shown should be 150N (15kg, 33lbs) min. 40mm If adjustment of the tool becomes necessary due to pull-off forces not being maintained, the following instructions should be followed. 1. Remove Hex socket grub screw using a 2mm A/F Hex key. 2. Using a screwdriver, turn the numbered wheel via the wheel adjustment screw. To increase the preload (and therefore the crimp pull-off force), turn the screw until the next number is shown. Even numbers are found by turning the screw clockwise, odd numbers are anti-clockwise. Turn the screw until the required number is level with the Hex socket grub screw hole. Hex socket grub screw 22-020 5 Wheel adjustment screw M22- 305 M22- 308 M22- 308 IS-05 Issue: 5 Date: 15.06.12 C/Note: 11756 Page 3 of 4 3. Re-fit the Hex socket grub screw and tighten. 4. Check the operating force as shown at the top of the page. Repeat the procedure if the force is incorrect. If the adjuster is set to maximum, and operating force is still not achieved, the tool has finished its working life (50,000 crimps minimum), and will need replacing. IS-05 Issue: 5 Date: 15.06.12 C/Note: 11756 Page 4 of 4