Orion Instruments ORS-300 Electro-Magnetic Switches

MODEL ORS-300
ELECTRO-MAGNETIC SWITCHES
DESCRIPTI0N
The Model ORS-300 reed switch is available to augment the control
capabilities of Orion’s extensive line of magnetic level indicators.
Housed in an explosion proof stainless steel enclosure, the ORS-300
mounts to the outside of the MLI via clamps. This mounting style
allows addition or repositioning of switches at any time, without
disruption of the process.
Each switch is designed for optimal repeatability and reliability. The
magnetic field produced by the MLI float actuates the ORS-300 when
the liquid level moves the float into the proximity of the reed switch.
The switch is bi-stable, so it will not reset until the float’s magnetic
field passes it in the opposite direction.
Model
ORS-300
For use in Installation Category II, Pollution Degree 2. If equipment is
used in a manner not specified by the manufacturer, protection provided by the equipment may be impaired.
S P E C I F I C AT I O N S
Model
Type
Contacts
Supply voltage
Contact rating
Maximum load
Dead band
Switch temperature range
Enclosure rating
Enclosure material
Mounting
AGENCY
ORS-300E-001
Bi-stable, reed switch
One SPDT
125 - 250 VAC/VDC
1.0 amps
25 Watts
±0.50" (13 mm) float travel
-58° to +325° F (-50° to +163° C)
NEMA 4X/7/9
316 stainless steel
Clamp mount to MLI
MODEL
APPROVAL CATEGORY
FM & CSA
ORS-300E-001
Class I, Div. 1, Grps B, C, & D
Class I, Div. 2, Grps A, B, C, & D
Class II, Grps E, F, & G
Class III, TYPE 4X
CE
ORS-300E-001
Installation Category II, Pollution Degree 2
Low Voltage Directives, 73/23/EEC & 93/68/EEC
per Harmonized Standard EN 61010-1/1993 & Amendment No. 1
MOUNTING
GEMINI
3.0 (76)
REF.
TO
AT L A S
OR
CAUTION: If equipment is used in a manner not specified by the
manufacturer, protection provided by the equipment may
be impaired.
With mounting clamps loosened, position ORS-300 reed switch on the
MLI body so that the centerline of the stainless steel tube which houses
the switch is at the desired switch point level. The switch should be
oriented so that the green ground screw is closest to the top of the
MLI. Tighten the clamps so that the switch is secured to the MLI. If
required, place the insulation between the MLI body and the switch
before tightening the clamps.
MOUNTING
TO
AURORA
Follow procedure for mounting to Atlas or Gemini, but ensure that the
switch is positioned on the circumference of the Aurora body as close
to the indicator as possible.
FLOAT ABOVE SWITCH
8-32 Ground Screw
1 (RED)
WIRING
3.00
(76.2)
0.84
(21.3)
C (WHITE)
The leads protruding from the potted end of the
switch housing are color coded as follows:
3.00
(76.2)
2 (BLACK)
FLOAT BELOW SWITCH
1 (RED)
1/2"
MNPT
1.00
(25.4)
White = Common
Black = Normally Closed
Red = Normally Open
C (WHITE)
2 (BLACK)
Note: For supply connections, use wire with a minimum rating of
+167° F (+75° C) as required by the process conditions. Use a
minimum of 14 AWG wire for power and ground field wires.
Note: Housing must be grounded via protective ground screw in base
of housing.
CAUTION: In hazardous areas, do not power the unit until the
conduit is sealed and the enclosure is screwed down
securely.
SWITCH FOR ATLAS
O R S - 3 Electric bi-stable 1 amp SPDT reed switch in stainless steel clamp-mounted housing, NEMA 4X/7/9
ENCLOSURE
0
2
3
O R S
3
Standard enclosure
Standard enclosure with cast aluminum junction box with terminal block (ORS-3 only)
Standard enclosure with stainless steel junction box with terminal block (ORS-3 only)
0
E
0 0
1
A Magnetrol Company
6646 Complex Drive • Baton Rouge, Louisiana 70809 • 225-906-2343 • Fax 225-906-2344 • www.orioninstruments.com
Copyright © 2003 Magnetrol International, Incorporated. All rights reserved. Printed in the USA.
Magnetrol and Magnetrol logotype are registered trademarks of Magnetrol International.
Performance specifications are effective with date of issue and are subject to change without notice.
The brand and product names contained within this document are trademarks or registered trademarks of their respective holders.
BULLETIN: ORS-300.1
EFFECTIVE: March 2004
SUPERSEDES: January 2003