Optoway BTRS-9700MG 1 *********************************************************************************************************************************************************************** BTRS-9700MG / BTRS-9700AMG 1550 nm TX / 1310 nm RX , 3.3V / 2.5 Gbps RoHS Compliant Single-Fiber MM Transceiver ********************************************************************************************************************************************************************** FEATURES DESCRIPTION l l l l l l l l l l l l l l The BTRS-9700MG series is high performance module for multi-mode single fiber communications by using 1550 nm transmitter and 1310 nm receiver. The transmitter section uses a multiple quantum well laser and is a class 1 laser compliant according to International Safety Standard IEC-60825. The receiver section uses an integrated 1310 nm detector preamplifier (IDP) mounted in an optical header and a limiting post-amplifier IC. A PECL logic interface simplifies interface to external circuitry. LV-TTL Signal Detect is used. Single Fiber Bi-Directional MM Transceiver Speed up to 2.67 Gb/s 1550 nm Transmitter 1310 nm Receiver Distance 0 to 300 m at 2.5 Gb/s 0 to 70oC Operating: BTRS-9700MG -20 to 85oC Operating: BTRS-9700AMG 2x5 Package with SC Receptacle or Pigtail LVTTL Signal Detect Output Single +3.3 V Power Supply RoHS Compliant PECL Differential Inputs and Outputs Wave Solderable and Aqueous Washable Class 1 Laser International Safety Standard IEC-60825 Compliant APPLICATIONS l WDM Gigabit Ethernet Links l SONET/SDH Equipment Interconnect l Fiber Channel Links LASER SAFETY This multi-mode transceiver is a Class 1 laser product. It complies with IEC-60825 and FDA 21 CFR 1040.10 and 1040.11. The transceiver must be operated within the specified temperature and voltage limits. The optical ports of the module shall be terminated with an optical connector or with a dust plug. ORDER INFORMATION P/No. BTRS-9700MG BTRS-9700AMG Bit Rate Distance (Gb/s) (m) 2.5 2.5 0 to 300 0 to 300 TX (nm) RX (nm) Voltage (V) Package Temp (oC) 1550 1550 1310 1310 3.3 3.3 SC, 2X5 SC, 2X5 0 to 70 -20 to 85 TX Power (dBm) 0 to -10 0 to -10 RX Sens. RoHS (dBm) Compliant -16 -16 Yes Yes Absolute Maximum Ratings Parameter Storage Temperature Operating Temperature Symbol Tstg Topr Soldering Temperature Power Supply Voltage Input Voltage --Vcc --- Output Current Iout Min -40 0 -20 Units o C o C 0 GND Max 85 70 85 260 3.6 Vcc 0 30 mA o C V V Notes BTRS-9700MG BTRS-9700AMG 10 seconds on leads only Recommended Operating Conditions Parameter Power Supply Voltage Operating Temperature Symbol Vcc Topr Data Rate Power Supply Current Icc Min 3.13 0 -20 1000 Typ 3.3 2488 Max 3.47 70 85 2670 260 Units / Notes V o C / BTRS-9700MG o C / BTRS-9700AMG Mb/s mA *********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: [email protected] http: // www.optoway.com.tw 10/1/2009 V2.0 Optoway BTRS-9700MG 2 ********************************************************************************************************************************************************************** Transmitter Specifications (0oC < Topr < 70oC, 3.13V < Vcc < 3. 47V) Parameter Optical Optical Transmit Power Output Center Wavelength Output Spectrum Width Output Eye Optical Rise Time Optical Fall Time Relative Intensity Noise Total Jitter Electrical Data Input Current – Low Data Input Current – High Differential Input Voltage Data Input Voltage – Low Data Input Voltage -- High Disable Input Voltage -- Low Disable Input Voltage -- High Shut Off Time for TxDis Symbol Min Typ Po -10 1480 λ σλ Compliant with IEEE 802.3z tr tf RIN TJ IIL IIH VIH - VIL VIL - VCC VIH - VCC V TDIS,L V TDIS,H tDIS Max Units Notes 0 1580 4 dBm nm nm 1 0.26 0.26 -120 0.227 ns ns dB/Hz ns 350 1600 -1.58 -0.74 0.8 Vcc 1 µA µA mV V V V V ms -350 300 -2.0 -1.1 0 Vcc – 1.3 RMS (σ) 20% to 80% Values 20% to 80% Values 2 3 3 TX Output Enabled TX Ouput Disabled Notes: 1. Output power is power coupled into a 62.5/125 µm multi-mode fiber. 2. Measured with a 27-1 PRBS. 3. These inputs are compatible with 10K, 10KH and 100K ECL and LVPECL inputs. Receiver Specifications (0oC < Topr < 70oC, 3.13 V < Vcc < 3. 47V) Parameter Optical Sensitivity Maximum Input Power Signal Detect -- Asserted Signal Detect -- Deasserted Signal detect -- Hysteresis Wavelength of Operation Optical Return Loss Electrical Data Output Voltage Swing SD Output Voltage -- Low SD Output Voltage -- High Signal Detect Assert Time Signal Detect Deassert Time Symbol Min Typ Max Units Notes --Pin Pa Pd ---3 ---31 1.0 1260 20 ----------- -16 ---16 --- dBm dBm dBm dBm dB nm dB 1 ORL V OH – VOL VOL VOH ASMAX ANSMAX 0.575 0 2.0 1360 0.930 0.8 Vcc+0.3 100 300 V V V µs µs Transition: low to high Transition: high to low 2 OFF to ON ON to OFF Notes: 1. Minimum sensitivity and saturation levels at BER 1E-10 for a 223-1 PRBS. 2. At least 30 dB optical isolation for the wavelength 1480 to 1580 nm. ********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 E-mail: [email protected] Fax: 886-3-5979737 http: // www.optoway.com.tw 10/1/2009 V2.0 Optoway BTRS-9700MG 3 ********************************************************************************************************************************************************************** CONNECTION DIAGRAM PIN 1 2 3 4 5 6 7 8 Symbol VEEr VCC r SD RD− RD+ VCC t VEEt TxDis 9 10 MS TD+ TDMS Notes Directly connect this pin to the receiver ground plane +3.3V dc power for the receiver section Active high on this indicates a received optical signal. Receiver Dataout Bar. See recommended circuit schematic Receiver Dataout. See recommended circuit schematic +3.3V dc power for the transmitter section Directly connect this plan to the transmitter ground plane Transmitter Disable. Connect this pin to +3.3V TTL logic “1” to disable module To enable module connect to TTL logic low “0” Transmitter Data In. See recommended circuit schematic Transmitter Data In Bar. See recommended circuit schematic Mounting Studs. Connect to Chassis Ground RECOMMENDED CIRCUIT SCHEMATIC depend on customer's PHY Vcc3.3V terminate and bias inside Transceiver module TDZ=50R LVPECL TD+ Z=5OR 10 9 8 7 6 130R 10nF 130R Vcc3.3V 1uH TDTD+ TDis Veet Vcct TXDis(LVTTL) 10nF 10uF 10uF PHY DEVICE Veer Vccr SD RDRD+ 1uH 1 2 3 4 5 BTRS-7XXXC 10nF Vcc3.3V 10uF RD+ 100R LVPECL Z=50R RDZ=5OR depend on customer's PHY SD TO LVTTL STAGE ********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: [email protected] http: // www.optoway.com.tw 10/1/2009 V2.0 Optoway BTRS-9700MG 4 ********************************************************************************************************************************************************************** PACKAGE DIAGRAM Units in mm Note: Specifications subject to change without notice. ********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 E-mail: [email protected] Fax: 886-3-5979737 http: // www.optoway.com.tw 10/1/2009 V2.0