Optoway BTR-77120-1510G 1 *********************************************************************************************************************************************************************** BTR-77120-1510G / BTR-77120C-1510G 1510 nm TX / 1590 nm RX , 3.3V / 1.25 Gb/s RoHS Compliant Single-Fiber Transceiver *********************************************************************************************************************************************************************** FEATURES DESCRIPTION l l l l l l l l l l l l l l The BTR-77120-1510G series is high performance module for single fiber communications by using 1510 nm transmitter and 1590 nm receiver. A guaranteed minimum optical link budget of 31 dB is offered which can correspond to a link distance of over 120 km (assuming worst case fiber loss of 0.22 dB/km).The transmitter section uses a multiple quantum well 1510 nm DFB laser and is a class 1 laser compliant according to International Safety Standard IEC-60825. The receiver section uses an integrated 1590 nm detector preamplifier (IDP) mounted in an optical header and a limiting post-amplifier IC. A PECL logic interface simplifies interface to external circuitry. Single Fiber Bi-Directional Transceiver 1510 nm DFB LD Transmitter 1590 nm Receiver 31 dB Link Power Budget At Least Link distance up to 120 km Industry Standard 1 x 9 Footprint Single +3.3 V Power Supply RoHS Compliant 0 to 70oC Operating LVPECL Differential Inputs and Outputs LVPECL Signal Detect Output: BTR-77120-1510G LVTTL Signal Detect Output : BTR-77120C-1510G Wave Solderable and Aqueous Washable Class 1 Laser International Safety Standard IEC-60825 Compliant LASER SAFETY This single mode transceiver is a Class 1 laser product. It complies with IEC-60825 and FDA 21 CFR 1040.10 and 1040.11. The transceiver must be operated within the specified temperature and voltage limits. The optical ports of the module shall be terminated with an optical connector or with a dust plug. APPLICATIONS l WDM 1.25 Gb/s Links l SONET/SDH Equipment Interconnect l Fiber Channel 1.063 Gb/s Links ORDER INFORMATION P/No. Bit Rate (Gb/s) Distance (km) TX (nm) RX (nm) Voltage Package (V) Temp (oC) TX Power (dBm) RX Sens. (dBm) Signal RoHS Detect Compliant BTR-77120-1510G 1.25 120 1510 DFB 1590 3.3 1X9 0 to 70 2 to -3 -34 TTL Yes BTR-77120C-1510G 1.25 120 1510 DFB 1590 3.3 1X9 0 to 70 2 to -3 -34 PECL Yes Note: 1. BTR-XXXXXG is 1X9 SC receptacle type package. 2. BTR-XXXXX-APBBBG is 1X9 pigtail type package with different connector, A=S is SC connector, A=F is FC connector, A=T is ST connector, A=L is LC connector, A=M is MU connector; BBB is the length of fiber in cm. Absolute Maximum Ratings Parameter Storage Temperature Operating Temperature Soldering Temperature Power Supply Voltage Input Voltage Output Current Symbol Tstg Topr --Vcc --Iout Min -40 0 0 GND Max 85 70 260 4.5 Vcc Units o C o C o C V V 0 30 mA Min 3.13 0 Typ 3.3 Max 3.47 70 1300 280 Notes 10 seconds on leads only Recommended Operating Conditions Parameter Power Supply Voltage Operating Temperature Data Rate Power Supply Current Symbol Vcc Topr 1250 Icc Units V o C Mb/s mA *********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: [email protected] http: // www.optoway.com.tw 10/1/2005 V2.0 Optoway BTR-77120-1510G 2 *********************************************************************************************************************************************************************** Transmitter Specifications (0 oC < Topr < 70 oC, 3.13V < Vcc < 3.47V) Parameter Optical Optical Transmit Power Output Center Wavelength Output Spectrum Width Side Mode Suppression Ratio Extinction Ratio Output Eye Optical Rise Time Optical Fall Time Relative Intensity Noise Total Jitter Electrical Data Input Current – Low Data Input Current – High Differential Input Voltage Data Input Voltage – Low Data Input Voltage -- High Symbol Min Po -3 1480 λ --∆λ SMSR 30 ER 9.0 Compliant with IEEE 802.3z tr tf RIN TJ IIL IIH VIH - VIL V IL - VCC V IH - VCC Typ Max Units Notes --- --- --- dBm nm nm dB dB 1 --- 2 1520 1 0.26 0.26 -120 0.227 ns ns dB/Hz ns -350 350 300 -2.0 -1.1 -1.58 -0.74 µA µA mV V V -20 dB Width 20% to 80% Values 20% to 80% Values 2 3 3 Notes: 1. Output power is power coupled into a 9/125 µm single mode fiber. 2. Measured with a 27-1 PRBS. 3. These inputs are compatible with 10K, 10KH and 100K ECL and LVPECL inputs. Receiver Specifications (0oC < Topr < 70oC, 3.13 V < Vcc < 3. 47V) Parameter Optical Sensitivity Maximum Input Power Signal Detect -- Asserted Signal Detect -- Deasserted Signal detect -- Hysteresis Wavelength of Operation Optical Return Loss Electrical Data Output Voltage – Low Data Output Voltage – High SD Output Voltage -- Low SD Output Voltage -- High SD Output Voltage -- Low SD Output Voltage -- High Symbol Min Typ Max Units Notes --Pin Pa Pd --- -34 ---34 --- dBm dBm dBm dBm dB nm dB 1 ORL ---9 ---43 1.0 1580 14 V OL - VCC V OH - VCC V OL - VCC V OH - VCC VOL V OH -2.0 -1.1 -2.0 -1.1 0 2.0 ------- 1620 -1.58 -0.74 -1.58 -0.74 0.8 Vcc+0.3 V V V V V V Transition: low to high Transition: high to low 2 3 3 BTR-77120-1510G BTR-77120C-1510G Notes: 1. Minimum sensitivity and saturation levels at BER=1E-12 for a 27-1 PRBS. 2. At least 30 dB optical isolation for the wavelength 1480 to 1520 nm. 3. These outputs are compatible with 10K, 10KH and 100K ECL and LVPECL outputs. *********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: [email protected] http: // www.optoway.com.tw 10/1/2005 V2.0 Optoway BTR-77120-1510G 3 *********************************************************************************************************************************************************************** CONNECTION DIAGRAM Receiver Signal Ground 1 (Rx GND) Receiver Data Out 2 (RD+) Receiver Data Out Bar 3 (RD−) Signal Detect 4 (SD) Receiver Power Supply 5 (Rx Vcc) Transmitter Power Supply 6 (Tx Vcc) Transmitter Data In Bar 7 (TD−) Transmitter Data In 8 (TD+) Transmitter Signal Ground 9 (Tx GND) PIN 1 2 3 4 5 6 7 8 9 Symbol Rx GND RD+ RD− SD Rx Vcc Tx Vcc TD− TD+ Tx GND N/C TOP VIEW N/C Notes Directly connect this pin to the receiver ground plane See recommended circuit schematic See recommended circuit schematic Active high on this indicates a received optical signal +3.3V dc power for the receiver section +3.3V dc power for the transmitter section See recommended circuit schematic See recommended circuit schematic Directly connect this plan to the trransmitter ground plane RECOMMENDED CIRCUIT SCHEMATIC Vcc3.3V Vcc3.3V Vcc3.3V R2 NA R3 NA R1 NA R4 NA C9 MICROSTRIP5 100nF C10 Z=50R MICROSTRIP6 100nF Z=5OR TDLVPECL TD+ L2 Vcc3.3V 1uH U2 9 8 7 6 5 4 3 2 1 TXGND TD+ TDTXVCC RXVCC SD RDRD+ RXGND BTR-77XX(C)/76XX(C) C2 C3 100nF 100nF C4 10uF L1 PHY DEVICE 1uH C1 C8 100nF 10uF Vcc3.3V RD+ C12 100nF R21 1K MICROSTRIP7 Z=50R MICROSTRIP8 R14 100R LVPECL RD- C11 100nF Z=5OR SD / LVPECL The split-load terminations for ECL signals need to be located at the input of devices receiving those ECL signals. The power supply filtering is required for good EMI performance. Use short tracks from the inductor L1/L2 to the module Rx Vcc and Tx Vcc. A GND plane under the module is required for good EMI and sensitivity performance. *********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: [email protected] http: // www.optoway.com.tw 10/1/2005 V2.0 Optoway BTR-77120-1510G 4 *********************************************************************************************************************************************************************** PACKAGE DIAGRAM Units in mm Note: Specifications subject to change without notice. *********************************************************************************************************************************************************************** OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: [email protected] http: // www.optoway.com.tw 10/1/2005 V2.0