2010 SMD Standard pedestal mount 0.6 Watt Wirewound Surface Mount Power Recessed-base mount F e at u r e s • 1% Tolerance standard • Smallest wirewound on the market • Available in low ohmic values 2010 Package S e r i e s s p e c i f i c at i o n s Series RW0S6BB Wattage 0.6 Ohms 0.01-1K Voltage 50 Characteristics Voltage 50V max. TCR Derating 500 Tolerance 1% Resistance range 0.010Ω–1KΩ 400 Temperature 0.1Ω–1Ω: ±90ppm Coefficient 1Ω–10Ω: ±50ppm 10Ω+: ±20ppm 300 100 Typical TCR for less than 0.1Ω SMD resistors (PPM/°C) 200 Dielectric 1000V Withstanding Voltage 80 60 40 20 0 100 Tape Size 12mm, 13” reel, 2500 pcs. per reel Percent Rated Power Power 0.6 watts at 25°C ambient 0 25 50 75 100 125 Ambient Temperature, °C 150 0.02 0.04 0.06 0.08 0.10 Ohms P e r f o r m a n c e D ATA Temp. cycle (-55°C to 125°C, 1000 cycles) ±0.5%+.05Ω Load Life (1000 hours at 25°C) ±3.0%+.05Ω 160 ±0.1%+.05Ω 140 Leaching (260°C Solder immersion, 60 sec.) Thermal Shock (Units at -55°C, then rated power applied) Flammability UL Material rating Package limit hot spot temperature rise 180 No visible leaching No mechanical damage UL94V0 Temperature rise, ϒC Immersion (260°C for 10 sec.) 200 Alumina FR4 120 100 80 60 40 Solder joint 20 100% 200% Percent Rated power 300% The temperature rise graph data was obtained by a selection of test substrate size and trace width for each resistor size to limit operating temperatures to safe values. The operating temperature safe rises are either 100°C substrate temperature rise or 180°C package hot spot temperature rise at 25°C ambient. FR4: 0.062 in. thick; 0.062 in. traces Alumina: 0.040 in. thick; 0.010 in. traces (continued) 1-866-9-OHMITE • Int’l 1-847-258-0300 • Fax 1-847-574-7522 • www.ohmite.com • [email protected] 39 2010 SMD 0.6 Watt Wirewound Surface Mount Power Dimensions 0.328" / 8.33mm 0.125" 3.20mm 0.006 Ref. Note 2 0.135" ±.005 3.420mm ±.127 E 0.079" ±.010 0.050" Nom. 2.00mm ±.254 1.280mm Nom. Land Pattern 0.10" ±.010 2.54mm ±.127 0.202" ±.010 5.140mm ±.508 0.005 ±.001 0.065" ±.012 1.640mm ±.305 0.095" Ref. 2.41mm Ref. Note 2: Test point is .020 above PCB. 0.078" / 1.98mm 0.026" / 0.66mm Note 3: Tape and reel dimensions per EIA 481 A except “EA” size which is 12 mm component pitch versus 16mm pitch. Land pattern dimensions are for reference only 0.126" 3.18mm Recommended for glue dot application ta p e a n d r e e l 0.795* 20.2 min. 0.059* 1.5 min. 0.724" 18.4mm 0.512 ±.008 13.0 ±.200 1.973 50 min. 13" nom. 0.488" +0.078/–0.00 12.4mm +2.0/–0.0 measured at hub Full Radius Tape Start Slot 0.098 / 2.5 min. width 0.394 / 10 min. depth Reels are compatible with major pickand-place machines and made in accordance with EIA 481 A. OR D ERIN G IN F OR M ATION Component type R = resistor Type of Base S = standard Standard Part Numbers for 2010 SMD Package B = 12mm Package Modifier A, B sequential Tolerance F = 1% �������������� Component Modifier W = wirewound Wattage 0S6 = 0.6W T = Tape and Reel (optional) E = RoHS compliant Resistance Value R = Decimal Examples: K = 1,000 R249 = 0.249 ohms M = 1,000,000 24R9 = 24.9 ohms 2K49 = 2,490 ohms Ohms Part Number 0.010 0.015 0.020 0.030 0.050 RW0S6BBR010FE RW0S6BBR015FE RW0S6BBR020FE RW0S6BBR030FE RW0S6BBR050FE 0.075 0.100 0.240 0.470 0.750 RW0S6BBR075FE RW0S6BBR100FE RW0S6BBR240FE RW0S6BBR470FE RW0S6BBR750FE 40 1-866-9-OHMITE • Int’l 1-847-258-0300 • Fax 1-847-574-7522 • www.ohmite.com • [email protected] Ohms 1.00 2.00 5.00 7.50 10.00 15.00 24.00 36.00 47.00 100.00 Part Number RW0S6BB1R00FE RW0S6BB2R00FE RW0S6BB5R00FE RW0S6BB7R50FE RW0S6BB10R0FE RW0S6BB15R0FE RW0S6BB24R0FE RW0S6BB36R0FE RW0S6BB47R0FE RW0S6BB100RFE