NLPR01S03A

NICHIA STS-DA1-3162 <Cat.No.140521>
NICHIA CORPORATION
SPECIFICATIONS FOR RED
STANDARD LED
NLPR01S03A
● LED reference standard with temperature control unit
for luminous intensity calibration
NICHIA STS-DA1-3162 <Cat.No.140521>
SPECIFICATIONS
(1) Absolute Maximum Ratings
Item
Forward Current
Allowable Reverse Current
Operating Temperature
Storage Temperature
Platinum Resistance
Temperature Device (RTD)
Current
Peltier Device Current
Peltier Device Voltage
Symbol
Absolute Maximum Rating
Unit
IF
30
mA
IR
50
mA
Topr
20~30
°C
Tstg
0~40
°C
Ipt
2
mA
Ipel
-1~1
A
Vpel
-3.2~3.2
V
* Absolute maximum ratings at TA=25°C.
(2) Initial Electrical/Optical Characteristics
Item
Forward Voltage
Luminous Intensity
Chromaticity Coordinate
Luminous
Directivity
Intensity
Chromaticity
Coordinate
Symbol
Condition
Typ
Unit
VF
Tpt=30°C, IF=20mA
2.00
V
Iv
Tpt=30°C, IF=20mA
0.85
cd
x
-
Tpt=30°C, IF=20mA
0.700
-
y
-
Tpt=30°C, IF=20mA
0.300
-
Iv(φ,θ)
Tpt=30°C, IF=20mA
within ±5% to mechanical axis
x,y(φ,θ)
Tpt=30°C, IF=20mA
within ±0.003 to mechanical axis
* Characteristics at TA=25°C.
* Luminous Intensity value as per CIE 127:2007 standard.
* Chromaticity Coordinates as per CIE 1931 Chromaticity Chart.
* Platinum RTD temperature (Tpt) must be controlled between 30°C and 35°C.
* The LED incorporated into the socket was characterized.
* The product seasoned for 200 hours at TA=25°C, IF=20mA was characterized.
(3) Lumen Maintenance
* Guaranteed maximum fluctuation of luminous intensity is ±3% of the initial value in a shorter time
between the time up to 100 hours of continuous operation and 1 year at TA=25°C, Tpt=30°C(±0.03°C), and IF=20mA(±0.1%).
1
NICHIA STS-DA1-3162 <Cat.No.140521>
DIRECTIONS FOR USE
(1) Auxiliary Equipment and System Requirements
● The following figure shows how the Luminous Flux Standard LED is connected.
Peltier Controller
This product
Constant Current Power
Supply for LED
Digital Multimeter
for Forward Voltage
Measurements
Recommended specifications for the peripheral equipment
Peltier Controller
PID Controller
Temperature measurement accuracy of ±0.03°C.
Constant Current Power Supply for LED
Digital Multimeter for Forward Voltage Measurements
Drive current accuracy: ≤ 0.1% of the set current
Input impedance: ≥ 1 GΩ
(2) Installation
● The following figure shows how the product should be held by a holder.
Example 1:
Example 2:
(Held by the part with 25 mm diameter)
(Held by the part with 20 mm diameter)
Holder
Holder
(3) Measurement
● The product should be measured when luminous intensity has stabilized after the start of temperature control
and constant current drive. Typically, this product will be stable and ready to be used for calibration within 1 to 3 minutes.
Please refer to “STABILITY” on the following page for the characteristics during the first 5 minutes after the LED starts emission.
2
NICHIA STS-DA1-3162 <Cat.No.140521>
OUTLINE DIMENSIONS
管理番号 No.
NLPx01S03A
STS-DA5-0029
(単位 Unit： mm, 公差 Tolerance：
(単位 Unit：±0.2)
mm)
10±0.1
26
34.6
(46)
3±0.5
+0
25 -0.1
5
3±0.5
+0
Parallel Pin Φ2-0.1
(1.2)
2.1±0.1
Case
16
+0
Φ20 -0.1
14.5
23
Plate
(5)
M6 Depth 7
34.3±0.5
機械軸
Mechanical Axis
基点（LED先端面）
Reference point (LED front tip)
項目 Item
Connector
数量 Quantity
内容 Description
Part No.: EGJ.0B.309.CLA
(from LEMO JAPAN Ltd.)
1
ケース
Case
材質：アルミニウム
Material: Aluminum
1
プレート
Plate
材質：樹脂
Material: POM
1
コネクタ
Connector
型番 NICHIA Part Number
シリアル番号 Serial Number
型番 NICHIA Part Number
NLP*01S03A
* - 発光色（例 W：白色）
* - Color (Example W:White)
シリアル番号 Serial Number
xxxxx
ロゴマーク NICHIA LED Mark
ロゴマーク NICHIA LED Mark
3
NICHIA STS-DA1-3162 <Cat.No.140521>
WIRING CONNECTION
管理番号 No.
NLPx01S03x
STS-DA5-0030
矢印方向から見たコネクタ図は以下を参照して下さい。
Refer to the following illustration for the connector pin numbering
(viewed from direction of the arrow).
8
7
1
2
9
6
5
3
4
1. LED点灯用（アノード側）
LED Anode to Power Supply
6. LED順電圧測定用（アノード側）
LED Anode for Forward Voltage measurement
保護素子
Protection
Device
ペルチェ素子 Peltier Device
Anode
LED
8. ペルチェ素子制御用（+）
Peltier Device (+)
白金測温抵抗素子 Platinum RTD
9. ペルチェ素子制御用（-）
Peltier Device (-)
Cathode
3. 白金測温抵抗素子（3 端子）
Platinum Temperature Sensor (3 Wire Type)
4. 白金測温抵抗素子（3 端子）
Platinum Temperature Sensor (3 Wire Type)
5. 白金測温抵抗素子（3 端子）
Platinum Temperature Sensor (3 Wire Type)
7. LED順電圧測定用（カソード側）
LED Cathode for Forward Voltage measurement
2. LED点灯用（カソード側）
LED Cathode for Power Supply
4
NICHIA STS-DA1-3162 <Cat.No.140521>
PACKAGING
5
NICHIA STS-DA1-3162 <Cat.No.140521>
OPTICAL CHARACTERISTICS
相対発光強度
Relative Emission Intensity (a.u.)
* 本特性は参考です。
All characteristics shown are for reference only and are not guaranteed.
Spectrum
発光スペクトル
Spectrum
管理番号 No.
1.0
NLPR01S03A
STS-DA5-0041
TA = 25°C
0.8
0.6
V(λ)
0.4
0.2
0.0
400
450
500
550
600
650
700
750
800
波長
Directivity1
Wavelength (nm)
指向特性
Directivity
光度
Luminous Intensity
-10°
0°
10°
-20°
放射角度
Radiation Angle
TA = 25°C
20°
30°
-30°
40°
-40°
50°
-50°
60°
-60°
-70°
70°
80°
-80°
-90°
90°
1
0.5
0.5
1
相対光度
Relative Luminosity　(a.u.)
Spectrum
色度
Chromaticity Coordinate
相対色度
Relative Chromaticity Coordinate
0
TA = 25°C
0.05
0.04
x
0.03
y
0.02
0.01
0.00
-0.01
-0.02
-0.03
-0.04
-0.05
-90
-60
-30
0
30
60
90
放射角度
Radiation Angle(°)
* 標準ＬＥＤに取り付けられた白金測温抵抗素子の温度が30°Cなるように温度コントロールしたときの特性です(IF = 20 mA)。
These characteristics are measured at IF = 20 mA and Tpt = 30°C.
* ペルチェコントローラーの温度制御安定度は±0.03°Cです(メーカー仕様値)。
The Stability of Peltier Controller is ±0.03°C (data from manufacturer specification).
6
NICHIA STS-DA1-3162 <Cat.No.140521>
OPTICAL CHARACTERISTICS(Enlarged)
* 本特性は参考です。
All characteristics shown are for reference only and are not guaranteed.
管理番号 No.
NLPR01S03A
STS-DA5-0042
指向特性
Directivity
Spectrum
光度
Luminous Intensity
TA = 25°C
相対光度
Relative Luminosity　(a.u.)
1.05
1.04
1.03
1.02
1.01
1.00
0.99
0.98
0.97
0.96
0.95
-5
-4
-3
-2
-1
0
1
2
3
4
5
放射角度
Radiation Angle(°)
Spectrum
相対色度
Relative Chromaticity Coordinate
色度
Chromaticity Coordinate
TA = 25°C
0.003
x
0.002
y
0.001
0.000
-0.001
-0.002
-0.003
-5
-4
-3
-2
-1
0
1
2
3
4
5
放射角度
Radiation Angle(°)
* 標準ＬＥＤに取り付けられた白金測温抵抗素子の温度が30°Cなるように温度コントロールしたときの特性です(IF = 20 mA)。
These characteristics are measured at IF = 20 mA and Tpt = 30°C.
* ペルチェコントローラーの温度制御安定度は±0.03°Cです(メーカー仕様値)。
The Stability of Peltier Controller is ±0.03°C (data from manufacturer specification).
7
NICHIA STS-DA1-3162 <Cat.No.140521>
STABILITY
* 本特性は参考です。
All characteristics shown are for reference only and are not guaranteed.
点灯時間 － 相対順電圧特性
Relative Forward Voltage
Over Time
0.5
TA = 30°C
T A = 25°C
T A = 20°C
TA = 30°C
T A = 25°C
T A = 20°C
0.4
相対光度
Relative Luminous Intensity (%)
0.003
0.002
0.001
0.000
-0.001
-0.002
-0.003
0.3
0.2
0.1
0.0
-0.1
-0.2
-0.3
-0.4
-0.5
-0.004
0
100
200
0
300
100
点灯時間
Time (sec)
Relative x Coordinate
Over Time
200
300
点灯時間
Time (sec)
点灯時間 - 相対色度 x特性
点灯時間 - 相対色度 y特性
Relative y Coordinate
Over Time
IfIv
TaIv
0.003
0.003
TA = 30°C
T A = 25°C
T A = 20°C
TA = 30°C
T A = 25°C
T A = 20°C
0.002
相対色度 y
Relative y Coordinate
0.002
相対色度 x
Relative x Coordinate
NLPR01S03A
STS-DA5-0043
点灯時間 - 相対光度
TaVf
Relative Luminous Intensity
Over Time
VfIf
0.004
相対順電圧
Relative Forward Voltage (V)
管理番号 No.
0.001
0.000
-0.001
-0.002
0.001
0.000
-0.001
-0.002
-0.003
-0.003
0
100
点灯時間
Time (sec)
200
300
0
100
200
300
点灯時間
Time (sec)
* 標準ＬＥＤに取り付けられた白金測温抵抗素子の温度が30°Cなるように温度コントロールしたときの特性です(IF = 20 mA)。
These characteristics are measured at IF = 20 mA and Tpt = 30°C.
* ペルチェコントローラーの温度制御安定度は±0.03°Cです(メーカー仕様値)。
The Stability of Peltier Controller is ±0.03°C (data from manufacturer specification).
* 点灯時間－相対順電圧特性、点灯時間－相対光度特性、点灯時間－相対色度x特性、点灯時間－相対色度y特性は、
TA=25°C、ＬＥＤ点灯300sec後の値を基準としています。
In the above graphs, the value at 300 seconds of the curve of TA = 25°C was set as the reference point.
8
NICHIA STS-DA1-3162 <Cat.No.140521>
CAUTIONS
(1) Storage
● The products should be stored in an air tight container with desiccant (silica gel) at 30°C or less and 70% RH or less.
● To avoid condensation, the products must not be stored in the areas where temperature and humidity fluctuate greatly.
● The LED incorporated in the product is silver plated. Customer is advised to store properly the products in controlled ambient
as exposure to a corrosive environment might cause the plated metal parts of the product to tarnish,
which might leads to adverse effects on optical characteristics.
(2) Handling Precautions
● Do not expose the product to shock. Failure to comply might affect on its characteristics.
(3) Electrostatic Discharge (ESD)
● The products are sensitive to static electricity or surge voltage. ESD can damage a die and its reliability.
When handling the products, the following measures against electrostatic discharge are strongly recommended:
Eliminating the charge
Grounded wriststrap, ESD footwear, clothes, and floors
Grounded workstation equipment and tools
ESD table/shelf mat made of conductive materials
● The customer is advised to check if the LEDs are damaged by ESD when performing the characteristics inspection of the LEDs
in the application. Damage can be detected with a forward voltage measurement or a light-up test at low current.
● ESD damaged LEDs may have a current flow at a low voltage or no longer illuminate at a low current.
Failure Criteria: VF<2.0V at IF=0.5mA
(4) Eye Safety
● The International Electrical Commission (IEC) published in 2006, IEC 62471:2006 Photobiological safety of lamps
and lamp systems which includes LEDs within its scope. Meanwhile LEDs were removed from the scope
of the IEC 60825-1:2007 laser safety standard, the 2001 edition of which included LED sources within its scope.
However, keep it mind that some countries and regions have adopted standards based on the IEC laser safety standard
IEC 60825-1:2001 which includes LEDs within its scope. Following IEC 62471:2006, most of Nichia LEDs can be classified
as belonging to either Exempt Group or Risk Group 1. Especially a high-power LED, that emits light containing blue wavelengths,
may be in Risk Group 2. Great care should be taken when viewing directly the LED driven at high current or the LED
with optical instruments, which greatly increase the hazard to your eyes.
● Viewing a flashing light may cause eye discomfort. When incorporating the LED into your product,
precaution should be taken to avoid adverse effect on human body caused by the light stimulus.
(5) Others
● This product is designed to be used for calibration.
Do not use this product for any other purposes or other applications.
● The customer shall not reverse engineer by disassembling or analysis of the LEDs without having prior written consent
from Nichia. When defective LEDs are found, the customer shall inform Nichia directly before disassembling or analysis.
● When a customer purchases this product, the customer and Nichia shall agree the official specification of the supplied products.
● Specifications and appearance subject to change for improvement without notice.
9