NHSW157BT

NICHIA STS-DA1-2084B <Cat.No.120830>
NICHIA CORPORATION
SPECIFICATIONS FOR WHITE LED
NHSW157BT
● Pb-free Reflow Soldering Application
● Built-in ESD Protection Device
● RoHS Compliant
NICHIA STS-DA1-2084B <Cat.No.120830>
SPECIFICATIONS
(1) Absolute Maximum Ratings
Symbol
Absolute Maximum Rating
Unit
Forward Current
Item
IF
35
mA
Pulse Forward Current
IFP
100
mA
Allowable Reverse Current
IR
85
mA
Power Dissipation
PD
115
mW
Operating Temperature
Topr
-40~100
°C
Storage Temperature
Tstg
-40~100
°C
Junction Temperature
TJ
120
°C
* Absolute Maximum Ratings at TA=25°C.
* IFP conditions with pulse width ≤10ms and duty cycle ≤10%.
(2) Initial Electrical/Optical Characteristics
Item
Forward Voltage
Luminous Flux
Rnn
R70
R8000
Chromaticity Coordinate
Symbol
Condition
Typ
Max
Unit
VF
IF=20mA
3.0
-
V
Φv
IF=20mA
8.8
-
lm
Luminous Intensity
Iv
IF=20mA
3.0
-
cd
Color Rendering Index
Ra
IF=20mA
-
-
-
Luminous Flux
Φv
IF=20mA
8.4
-
lm
Luminous Intensity
Iv
IF=20mA
2.9
-
cd
Color Rendering Index
Ra
IF=20mA
75
-
-
Luminous Flux
Φv
IF=20mA
7.6
-
lm
Luminous Intensity
Iv
IF=20mA
2.6
-
cd
Color Rendering Index
Ra
IF=20mA
83
-
-
x
-
IF=20mA
0.344
-
-
y
-
IF=20mA
0.355
-
-
RθJS
-
27
54
°C/W
Thermal Resistance
* Characteristics at TA=25°C.
* Luminous Flux value as per CIE 127:2007 standard.
* Chromaticity Coordinates as per CIE 1931 Chromaticity Chart.
* RθJS is Thermal Resistance from junction to TS measuring point.
1
NICHIA STS-DA1-2084B <Cat.No.120830>
RANKS
Item
Rank
Forward Voltage
Luminous Flux
Color Rendering Index
Min
Max
Unit
V
-
2.6
3.3
P4
9.0
10.7
P3
7.6
9.0
P2
6.4
7.6
P1
5.4
6.4
lm
Rnn
Ra
-
-
-
R70
Ra
70
-
-
Ra
80
-
-
R9
0
-
-
R8000
Color Ranks
Rank b3
Rank b4
x
0.2870
0.2830
0.3040
0.3070
x
0.3070
0.3040
0.3300
0.3300
y
0.2950
0.3050
0.3300
0.3150
y
0.3150
0.3300
0.3600
0.3390
x
0.2960
0.2870
0.3070
0.3110
x
0.3110
0.3070
0.3300
0.3300
y
0.2760
0.2950
0.3150
0.2940
y
0.2940
0.3150
0.3390
0.3180
Rank b5
Rank b6
Rank c1
Rank c2
x
0.3300
0.3300
0.3610
0.3570
x
0.3300
0.3300
0.3570
0.3560
y
0.3390
0.3600
0.3850
0.3610
y
0.3180
0.3390
0.3610
0.3510
Rank sw50
Rank sw57
x
0.3366
0.3376
0.3548
0.3515
x
0.3221
0.3207
0.3376
0.3366
y
0.3369
0.3616
0.3736
0.3487
y
0.3261
0.3462
0.3616
0.3369
Rank sw65
x
0.3070
0.3040
0.3207
0.3221
y
0.3113
0.3300
0.3462
0.3261
* Ranking at TA=25°C.
* Forward Voltage Tolerance: ±0.05V
* Luminous Flux Tolerance: ±7%
* Color Rendering Index Ra Tolerance: ±2
* Color Rendering Index R9 Tolerance: ±6.5
* The R9 value for the above rank shall be greater than 0.
* Chromaticity Coordinate Tolerance: ±0.005
* LEDs from the above ranks will be shipped.
The rank combination ratio per shipment will be decided by Nichia.
Luminous Flux Ranks by Color Rank, Color Rendering Index Rank
Ranking by
Luminous Flux
Ranking by
P1
P2
P3
P4
Color Coordinates, Color Rendering Index
b3,b4,b5,b6,c1,c2
sw50,sw57,sw65
Rnn
R70
R8000
2
NICHIA STS-DA1-2084B <Cat.No.120830>
CHROMATICITY DIAGRAM
0.45
0.40
sw50
sw57
c1
sw65
0.35
y
b4
c2
b3
0.30
b6
b5
0.25
0.20
0.20
0.25
0.30
0.35
0.40
0.45
x
3
NICHIA STS-DA1-2084B <Cat.No.120830>
OUTLINE DIMENSIONS
* 本製品はRoHS指令に適合しております。
This product complies with RoHS Directive.
管理番号 No.
NHSx157B
STS-DA7-1917
(単位 Unit:±0.2)
mm)
(単位 Unit: mm, 公差 Tolerance:
0.52
3
(2.6)
1.4
(1)
(0.2)
Cathode
1.56
0.86
(0.6)
(0.3)
2.6
Anode
0.54
項目 Item
内容 Description
パッケージ材質
Package Materials
電極材質
Electrodes Materials
耐熱性ポリマー
Heat-Resistant Polymer
シリコーン樹脂
（拡散剤+蛍光体入り）
Silicone Resin
(with diffuser and phosphor)
銅合金+銀メッキ
Ag-plated Copper Alloy
質量
Weight
0.0061g(TYP)
封止樹脂材質
Encapsulating Resin
Materials
* バリは寸法に含まないものとします。
Dimensions do not include mold flash or metal burr.
K
A
保護素子
Protection Device
4
NICHIA STS-DA1-2084B <Cat.No.120830>
SOLDERING
• Recommended Reflow Soldering Condition(Lead-free Solder)
1 to 5°C per sec
260°C Max
10sec Max
Pre-heat
180 to 200°C
• Recommended Hand Soldering Condition
Temperature
350°C Max
Soldering Time
3sec Max
60sec Max
Above 220°C
120sec Max
• Recommended Metal Solder Stencil Aperture
2.4
0.6
1.66
0.5
0.64
0.6
0.6
1.56
0.7
0.54
1 .5 5
0 .6 6
0.8
1 .5 5
0 .8 6
0.8
0 .8 6
• Recommended Soldering Pad Pattern
0.6
(単位 Unit: mm)
* This LED is designed to be reflow soldered on to a PCB. If dip soldered, Nichia cannot guarantee its reliability.
* Reflow soldering must not be performed more than twice. Hand soldering must not be performed more than once.
* Avoid rapid cooling. Ramp down the temperature gradually from the peak temperature.
* Nitrogen reflow soldering is recommended. Air flow soldering conditions can cause optical degradation,
caused by heat and/or atmosphere.
* Since the silicone used in the encapsulating resin is soft, do not press on the encapsulant resin.
Pressure can cause nicks, chip-outs, encapsulant delamination and deformation, and wire breaks, decreasing reliability.
* Repairing should not be done after the LEDs have been soldered. When repairing is unavoidable,
a double-head soldering iron should be used.
It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing.
* When soldering, do not apply stress to the LED while the LED is hot.
5
NICHIA STS-DA1-2084B <Cat.No.120830>
TAPE AND REEL DIMENSIONS
3.5 ±0.05
Cathode
4±0.1
(単位 Unit: mm)
0.2±0.05
3.25 ±0.1
2±0.05
Nxxx157x
STS-DA7-0071B
8 +0.3
-0.1
4±0.1
Φ1.5+0.1
-0
管理番号 No.
1.75 ±0.1
テーピング部 Tape
Φ1+0.1
-0
0.65±0.1
1.6±0.1
エンボスキャリアテープ
Embossed Carrier Tape
トレーラ部/リーダ部 Trailer and Leader
トップカバーテープ
Top Cover Tape
引き出し方向
Feed
Direction
トレーラ部最小160mm（空部）
Trailer 160mm MIN(Empty Pockets)
LED装着部
Loaded Pockets
引き出し部最小100mm（空部）
Leader with Top Cover Tape
100mm MIN(Empty Pocket)
リーダ部最小400mm
Leader without Top Cover Tape 400mm MIN
リール部 Reel
180+0
-3
11.4±1
9±0.3
* 数量は1リールにつき 5000個入りです。
Quantity per reel=5000pcs
Φ
* JIS C 0806電子部品テーピングに準拠しています。
The tape packing method complies with JIS C 0806
(Packaging of Electronic Components on Continuous Tapes).
±
21
±0.2
ラベル
Label
Φ
13 ±
0.
2
f 13
.8
Φ60 +1
-0
8
0.
f2
1 ±0
6
NICHIA STS-DA1-2084B <Cat.No.120830>
PACKAGING - TAPE & REEL
シリカゲルとともにリールをアルミ防湿袋に入れ、熱シールにより封をします。
Reels are shipped with desiccants in heat-sealed moisture-proof bags.
管理番号 No.
Nxxxxxxx
STS-DA7-0006C
ラベル Label
リール
Reel
シリカゲル
Desiccants
XXXX LED
TYPE Nxxxxxxx
*******
LOT YMxxxx-RRR
QTY.
PCS
RoHS
NICHIA CORPORATION 491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN
熱シール
Seal
アルミ防湿袋
Moisture-proof Bag
アルミ防湿袋を並べて入れ、ダンボールで仕切ります。
Moisture-proof bags are packed in cardboard boxes
with corrugated partitions.
ラベル Label
XXXX LED
TYPE Nxxxxxxx
*******
RANK RRR
PCS
QTY.
RoHS
NICHIA CORPORATION
491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN
Nichia
LED
* 客先型名を*******で示します。
客先型名が設定されていない場合は空白です。
******* is the customer part number.
If not provided, it will not be indicated on the label.
* ロット表記方法についてはロット番号の項を
参照して下さい。
For details, see "LOT NUMBERING CODE"
in this document.
* ランク分けがない場合はランク表記はありません。
The label does not have the RANK field for
un-ranked products.
* 本製品はテーピングしたのち、輸送の衝撃から保護するためダンボールで梱包します。
Products shipped on tape and reel are packed in a moisture-proof bag.
They are shipped in cardboard boxes to protect them from external forces during transportation.
* 取り扱いに際して、落下させたり、強い衝撃を与えたりしますと、製品を損傷させる原因になりますので注意して下さい。
Do not drop or expose the box to external forces as it may damage the products.
* ダンボールには防水加工がされておりませんので、梱包箱が水に濡れないよう注意して下さい。
Do not expose to water. The box is not water-resistant.
* 輸送、運搬に際して弊社よりの梱包状態あるいは同等の梱包を行って下さい。
Using the original package material or equivalent in transit is recommended.
7
NICHIA STS-DA1-2084B <Cat.No.120830>
LOT NUMBERING CODE
Lot Number is presented by using the following alphanumeric code.
YMxxxx - RRR
Y - Year
Year
Y
2009
9
2010
A
2011
B
2012
C
2013
D
2014
E
M - Month
Month
M
Month
M
1
1
7
7
2
2
8
8
3
3
9
9
4
4
10
A
5
5
11
B
6
6
12
C
xxxx-Nichia's Product Number
RRR-Ranking by Color Coordinates, Ranking by Luminous Flux, Ranking by Color Rendering Index
8
NICHIA STS-DA1-2084B <Cat.No.120830>
DERATING CHARACTERISTICS
管理番号 No.
NHSx157B
STS-DA7-1924
カソード側はんだ接合部温度-許容順電流特性
Solder Temperature(Cathode Side) vs
Allowable Forward Current
Derating2
許容順電流
Allowable Forward Current(mA)
50
40
(100, 35.0)
30
20
10
0
0
20
40
60
80
100
120
カソード側はんだ接合部温度
Solder Temperature(Cathode Side)(°C)
デューティー比-許容順電流特性
Duty Ratio vs
Allowable Forward Current
Duty
TA =25°C
許容順電流
Allowable Forward Current(mA)
1000
100
35
10
1
10
100
デューティー比
Duty Ratio(%)
9
NICHIA STS-DA1-2084B <Cat.No.120830>
OPTICAL CHARACTERISTICS
NHSW157B
管理番号 No. STS-DA7-1915A
* 本特性は参考です。
All characteristics shown are for reference only and are not guaranteed.
発光スペクトル
Spectrum
T A=25°C
IF=20mA
Spectrum
1.0
相対発光強度
Relative Emission Intensity(a.u.)
0.8
0.6
0.4
0.2
0.0
350
400
450
500
550
600
650
700
750
波長
Wavelength(nm)
Directivity1
指向特性
Directivity
T A=25°C
IFP=20mA
-20°
-10°
0°
10°
20°
30°
-30°
40°
-40°
50°
放射角度
Radiation Angle
-50°
-60°
60°
70°
-70°
80°
-80°
-90°
90°
1
0.5
0
0.5
1
相対照度
Relative Illuminance(a.u.)
* 本特性は演色性ランクRnn に対応しています。
The graphs above show the characteristics for Rnn LEDs of this product.
10
NICHIA STS-DA1-2084B <Cat.No.120830>
OPTICAL CHARACTERISTICS
* 本特性は参考です。
All characteristics shown are for reference only and are not guaranteed.
管理番号 No.
発光スペクトル
Spectrum
NHSW157B
STS-DA7-2682
T A=25°C
IF=20mA
Spectrum
1.0
相対発光強度
Relative Emission Intensity(a.u.)
0.8
0.6
0.4
0.2
0.0
350
400
450
500
550
600
650
700
750
波長
Wavelength(nm)
Directivity1
指向特性
Directivity
T A=25°C
IFP=20mA
-20°
-10°
0°
10°
20°
30°
-30°
40°
-40°
50°
放射角度
Radiation Angle
-50°
-60°
60°
70°
-70°
80°
-80°
-90°
90°
1
0.5
0
0.5
1
相対照度
Relative Illuminance(a.u.)
* 本特性は演色性ランクR70 に対応しています。
The graphs above show the characteristics for R70 LEDs of this product.
11
NICHIA STS-DA1-2084B <Cat.No.120830>
OPTICAL CHARACTERISTICS
* 本特性は参考です。
All characteristics shown are for reference only and are not guaranteed.
管理番号 No.
発光スペクトル
Spectrum
NHSW157B
STS-DA7-3467
T A=25°C
IF=20mA
Spectrum
1.0
相対発光強度
Relative Emission Intensity(a.u.)
0.8
0.6
0.4
0.2
0.0
350
400
450
500
550
600
650
700
750
波長
Wavelength(nm)
Directivity1
指向特性
Directivity
T A=25°C
IFP=20mA
-20°
-10°
0°
10°
20°
30°
-30°
40°
-40°
50°
放射角度
Radiation Angle
-50°
-60°
60°
70°
-70°
80°
-80°
-90°
90°
1
0.5
0
0.5
1
相対照度
Relative Illuminance(a.u.)
* 本特性は演色性ランクR8000に対応しています。
The graphs above show the characteristics for R8000 LEDs of this product.
12
NICHIA STS-DA1-2084B <Cat.No.120830>
FORWARD CURRENT CHARACTERISTICS / TEMPERATURE CHARACTERISTICS
* 本特性は参考です。
All characteristics shown are for reference only and are not guaranteed.
順電圧-順電流特性
Forward Voltage vs
Forward Current
管理番号 No.
周囲温度-順電圧特性
Ambient Temperature vs
Forward Voltage
VfIf
T A=25°C
100
NHSx157B
STS-DA7-1913
IFP=5mA
IFP=20mA
IFP=60mA
TaVf
4.5
順電圧
Forward Voltage(V)
順電流
Forward Current(mA)
4.0
20
10
3.5
3.0
2.5
1
2.0
2.0
2.5
3.0
3.5
4.0
4.5
-60 -40 -20
順電圧
Forward Voltage(V)
順電流-相対光束特性
Forward Current vs
Relative Luminous Flux
0
20
40
60
80
100 120
周囲温度
Ambient Temperature(°C)
周囲温度-相対光束特性
Ambient Temperature vs
Relative Luminous Flux
IfIv
T A=25°C
TaIv
IFP= 20mA
1.4
6
相対光束
Relative Luminous Flux(a.u.)
相対光束
Relative Luminous Flux(a.u.)
5
4
3
2
1.2
1.0
0.8
1
0.6
0
0
20
40
60
80
順電流
Forward Current(mA)
100
120
-60 -40 -20
0
20
40
60
80
100 120
周囲温度
Ambient Temperature(°C)
13
NICHIA STS-DA1-2084B <Cat.No.120830>
FORWARD CURRENT CHARACTERISTICS / TEMPERATURE CHARACTERISTICS
NHSW157B
管理番号 No. STS-DA7-1916A
* 本特性は参考です。
All characteristics shown are for reference only and are not guaranteed.
順電流-色度特性
Forward Current vs
Chromaticity Coordinate
Ifxy
TA =25°C
0.37
y
0.36
1mA
5mA
20mA
35mA
0.35
100mA
0.34
0.33
0.32
0.33
0.34
0.35
0.36
x
周囲温度-色度特性
Ambient Temperature vs
Chromaticity Coordinate
Taxy
I FP= 20mA
0.37
-40°C
0.36
0°C
25°C
y
50°C
0.35
100°C
0.34
0.33
0.32
0.33
0.34
0.35
0.36
x
* 本特性は演色性ランクRnn に対応しています。
The graphs above show the characteristics for Rnn LEDs of this product.
14
NICHIA STS-DA1-2084B <Cat.No.120830>
FORWARD CURRENT CHARACTERISTICS / TEMPERATURE CHARACTERISTICS
* 本特性は参考です。
All characteristics shown are for reference only and are not guaranteed.
順電流-色度特性
Forward Current vs
Chromaticity Coordinate
管理番号 No.
NHSW157B
STS-DA7-2683
Ifxy
TA =25°C
0.37
0.36
1mA
y
20mA
100mA
0.35
0.34
0.33
0.32
0.33
0.34
0.35
0.36
x
周囲温度-色度特性
Ambient Temperature vs
Chromaticity Coordinate
Taxy
I FP= 20mA
0.37
-40°C
0.36
0°C
25°C
y
50°C
0.35
100°C
0.34
0.33
0.32
0.33
0.34
0.35
0.36
x
* 本特性は演色性ランク R70に対応しています。
The graphs above show the characteristics for R70 LEDs of this product.
15
NICHIA STS-DA1-2084B <Cat.No.120830>
FORWARD CURRENT CHARACTERISTICS / TEMPERATURE CHARACTERISTICS
* 本特性は参考です。
All characteristics shown are for reference only and are not guaranteed.
順電流-色度特性
Forward Current vs
Chromaticity Coordinate
管理番号 No.
NHSW157B
STS-DA7-3468
Ifxy
TA =25°C
0.38
0.37
0.36
y
1mA
20mA
100mA
0.35
0.34
0.33
0.32
0.33
0.34
0.35
0.36
0.37
x
周囲温度-色度特性
Ambient Temperature vs
Chromaticity Coordinate
Taxy
I FP= 20mA
0.38
0.37
-40°C
0.36
0°C
y
25°C
50°C
0.35
100°C
0.34
0.33
0.32
0.33
0.34
0.35
0.36
0.37
x
* 本特性は演色性ランクR8000に対応しています。
The graphs above show the characteristics for R8000 LEDs of this product.
16
NICHIA STS-DA1-2084B <Cat.No.120830>
RELIABILITY
(1) Tests and Results
Reference
Test
Standard
Resistance to
Test
Test Conditions
Duration
JEITA ED-4701
Tsld=260°C, 10sec, 2reflows,
300 301
Precondition: 30°C, 70%RH, 168hr
Solderability
JEITA ED-4701
Tsld=245±5°C, 5sec,
(Reflow Soldering)
303 303A
Lead-free Solder(Sn-3.0Ag-0.5Cu)
JEITA ED-4701
-40°C(30min)~25°C(5min)~
100 105
100°C(30min)~25°C(5min)
Moisture Resistance
JEITA ED-4701
25°C~65°C~-10°C, 90%RH,
(Cyclic)
200 203
24hr per cycle
High Temperature
JEITA ED-4701
Storage
200 201
Temperature Humidity
JEITA ED-4701
Storage
100 103
Low Temperature
JEITA ED-4701
Storage
200 202
Soldering Heat
(Reflow Soldering)
Temperature Cycle
#2
0/22
100cycles
#1
0/50
10cycles
#1
0/22
TA=100°C
1000hours
#1
0/22
TA=60°C, RH=90%
1000hours
#1
0/22
TA=-40°C
1000hours
#1
0/22
1000hours
#1
0/22
500hours
#1
0/22
1000hours
#1
0/22
48minutes
#1
0/22
#1
0/22
#1
0/22
Operating Life
Test board: See NOTES below
Temperature Humidity
60°C, RH=90%, IF=20mA
Operating Life
Test board: See NOTES below
Low Temperature
TA=-40°C, IF=20mA
Operating Life
Test board: See NOTES below
JEITA ED-4701
200m/s2, 100~2000~100Hz,
400 403
4cycles, 4min, each X, Y, Z
JEITA ED-4701
HBM, 2kV, 1.5kΩ, 100pF, 3pulses,
300 304
alternately positive or negative
Soldering Joint Shear
JEITA ED-4702B
Strength
002 3
Failed/Tested
0/22
TA=100°C, IF=35mA
Electrostatic Discharges
#
Units
#1
High Temperature
Vibration
Failure
Criteria
5N, 10±1sec
NOTES:
1) Test board: FR4 board thickness=1.6mm, copper layer thickness=0.07mm, RθJA≈113°C/W
2) Measurements are performed after allowing the LEDs to return to room temperature.
(2) Failure Criteria
Criteria #
#1
#2
Items
Conditions
Failure Criteria
Forward Voltage(VF)
IF=20mA
>U.S.L.×1.1
Luminous Flux(ΦV)
IF=20mA
<L.S.L.×0.7
Solderability
-
Less than 95% solder coverage
U.S.L. : Upper Specification Limit
L.S.L. : Lower Specification Limit
17
NICHIA STS-DA1-2084B <Cat.No.120830>
CAUTIONS
(1) Storage
Conditions
Storage
Temperature
Humidity
Time
Before Opening Aluminum Bag
≤30°C
≤90%RH
Within 1 Year from Delivery Date
After Opening Aluminum Bag
≤30°C
≤70%RH
≤168hours
65±5°C
-
≥24hours
Baking
● Product complies with JEDEC MSL 3 or equivalent. See IPC/JEDEC STD-020 for moisture-sensitivity details.
● Absorbed moisture in LED packages can vaporize and expand during soldering, which can cause interface delamination
and result in optical performance degradation. Products are packed in moisture-proof aluminum bags
to minimize moisture absorption during transportation and storage.
Included silica gel desiccants change from blue to red if moisture had penetrated bags.
● After opening the moisture-proof aluminum bag, the products should go through the soldering process
within the range of the conditions stated above. Unused remaining LEDs should be stored with silica gel desiccants
in a hermetically sealed container, preferably the original moisture-proof bags for storage.
● After the “Period After Opening” storage time has been exceeded or silica gel desiccants are no longer blue,
the products should be baked. Baking should only be done once.
● Customer is advised to keep the LEDs in an airtight container when not in use. Exposure to a corrosive environment
may cause the plated metal parts of the product to tarnish, which could adversely affect soldering and optical characteristics.
It is also recommended to return the LEDs to the original moisture proof bags and reseal.
● After assembly and during use, silver plating can be affected by the corrosive gases emitted by components and materials
in close proximity of the LEDs within an end product, and the gases entering into the product from the external atmosphere.
The above should be taken into consideration when designing.
Resin materials, in particular, may contain substances which can affect silver plating, such as halogen.
● Do not use sulfur-containing materials in commercial products. Some materials, such as seals and adhesives, may contain sulfur.
The extremely corroded or contaminated plating of LEDs might cause an open circuit. Silicone rubber is recommended
as a material for seals. Bear in mind, the use of silicones may lead to silicone contamination of electrical contacts
inside the products, caused by low molecular weight volatile siloxane.
● To prevent water condensation, please avoid large temperature and humidity fluctuations for the storage conditions.
(2) Directions for Use
● When designing a circuit, the current through each LED must not exceed the Absolute Maximum Rating.
Operating at a constant current per LED is recommended. In case of operating at a constant voltage, Circuit B is recommended.
If the LEDs are operated with constant voltage using Circuit A, the current through the LEDs may vary due to the variation
in Forward Voltage characteristics of the LEDs.
(A)
(B)
...
...
● LEDs should be operated in forward bias. Driving circuits must not subject LEDs to either forward or reverse voltage while off.
Continuous reverse voltage can cause migration and LED damage.
● It is recommended to operate the LEDs at a current greater than 10% of the sorting current to stabilize the LED characteristics.
● For outdoor use, necessary measures should be taken to prevent water, moisture and salt air damage.
(3) Handling Precautions
● Do not handle LEDs with bare hands, it may contaminate the LED surface and affect optical characteristics.
In the worst case, catastrophic failure from excess pressure through wire-bond breaks and package damage may result.
● When handling the product with tweezers, be careful not to apply excessive force to the resin.
Otherwise, The resin can be cut, chipped, delaminate or deformed, causing wire-bond breaks and catastrophic failures.
● Dropping the product may cause damage.
● Do not stack assembled PCBs together. Failure to comply can cause the resin portion of the product to be cut, chipped,
delaminated and/or deformed. It may cause wire to break, leading to catastrophic failures.
18
NICHIA STS-DA1-2084B <Cat.No.120830>
(4) Design Consideration
● PCB warpage after mounting the products onto a PCB can cause the package to break.
The LED should be placed in a way to minimize the stress on the LEDs due to PCB bow and twist.
● The position and orientation of the LEDs affect how much mechanical stress is exerted on the LEDs placed near the score lines.
The LED should be placed in a way to minimize the stress on the LEDs due to board flexing.
● Board separation must be performed using special jigs, not using hands.
(5) Electrostatic Discharge (ESD)
● The products are sensitive to static electricity or surge voltage. ESD can damage a die and its reliability.
When handling the products, the following measures against electrostatic discharge are strongly recommended:
Eliminating the charge
Grounded wrist strap, ESD footwear, clothes, and floors
Grounded workstation equipment and tools
ESD table/shelf mat made of conductive materials
● Proper grounding is required for all devices, equipment, and machinery used in product assembly.
Surge protection should be considered when designing of commercial products.
● If tools or equipment contain insulating materials such as glass or plastic,
the following measures against electrostatic discharge are strongly recommended:
Dissipating static charge with conductive materials
Preventing charge generation with moisture
Neutralizing the charge with ionizers
● The customer is advised to check if the LEDs are damaged by ESD
when performing the characteristics inspection of the LEDs in the application.
Damage can be detected with a forward voltage measurement or a light-up test at low current (≤1mA).
● ESD damaged LEDs may have current flow at a low voltage or no longer illuminate at a low current.
Failure Criteria: VF<2.0V at IF=0.5mA
(6) Thermal Management
● Proper thermal management is an important when designing products with LEDs. LED die temperature is affected
by PCB thermal resistance and LED spacing on the board. Please design products in a way that the LED die temperature
does not exceed the maximum Junction Temperature (TJ).
● Drive current should be determined for the surrounding ambient temperature (TA) to dissipate the heat from the product.
● The following equations can be used to calculate the junction temperature of the products.
1) TJ=TA+RθJA･W
2) TJ=TS+RθJS･W
*TJ=LED junction temperature: °C
TA=Ambient temperature: °C
TS=Soldering temperature (cathode side): °C
RθJA=Thermal resistance from junction to ambient: °C/W
RθJS=Thermal resistance from junction to TS measuring point: °C/W
W=Input power(IF×VF): W
Ts Point
(7) Cleaning
● If required, isopropyl alcohol (IPA) should be used. Other solvents may cause premature failure to the LEDs
due to the damage to the resin portion. The effects of such solvents should be verified prior to use.
In addition, the use of CFCs such as Freon is heavily regulated.
● Ultrasonic cleaning is not recommended since it may have adverse effects on the LEDs
depending on the ultrasonic power and how LED is assembled.
If ultrasonic cleaning must be used, the customer is advised to make sure the LEDs will not be damaged prior to cleaning.
19
NICHIA STS-DA1-2084B <Cat.No.120830>
(8) Eye Safety
● In 2006, the International Electrical Commission (IEC) published IEC 62471:2006 Photobiological safety of lamps
and lamp systems, which added LEDs in its scope.
On the other hand, the IEC 60825-1:2007 laser safety standard removed LEDs from its scope.
However, please be advised that some countries and regions have adopted standards
based on the IEC laser safety standard IEC 60825-1:20112001, which still includes LEDs in its scope.
Most of Nichia's LEDs can be classified as belonging into either the Exempt Group or Risk Group 1.
High-power LEDs, that emit light containing blue wavelengths, may be classified as Risk Group 2.
Please proceed with caution when viewing directly any LEDs driven at high current, or viewing LEDs
with optical instruments which may greatly increase the damages to your eyes.
● Viewing a flashing light may cause eye discomfort. When incorporating the LED into your product,
please be careful to avoid adverse effects on the human body caused by light stimulation.
(9) Others
● The LEDs described in this brochure are intended to be used for ordinary electronic equipment (such as office equipment,
communications equipment, measurement instruments and household appliances).
Consult Nichia's sales staff in advance for information on the applications in which exceptional quality
and reliability are required, particularly when the failure or malfunction of the LEDs may directly jeopardize life or
health (such as for airplanes, aerospace, submersible repeaters, nuclear reactor control system, automobiles,
traffic control equipment, life support systems and safety devices).
● The customer shall not reverse engineer by disassembling or analysis of the LEDs without having prior written consent
from Nichia. When defective LEDs are found, the customer shall inform Nichia directly before disassembling or analysis.
● Both the customers and Nichia will agree on official specifications of supplied products before a customer's volume production.
● Specifications and appearance subject to change for improvement without notice.
20