F98 - Nichicon

SOLID TANTALUM ELECTROLYTIC CAPACITORS
F98
Resin-molded Chip,
High Capacitance Series
Specifications
Compliant to the RoHS directive (2002/95/EC).
Item
Applications
Smartphone
Mobile phone
Wireless module
Hearing aid
Performance Characteristics
Category
Temperature Range
--55 to +125°C (Rated temperature : +85°C)
Capacitance Tolerance
±20% (at 120Hz)
Dissipation Factor
Refer to the table below
ESR
Refer to the table below
Leakage Current
Refer to the table below
Provided that
After 5 minute's application of rated voltage, leakage current at 85°C,
10 times or less than 20°C specified value.
After 5 minute's application of rated voltage, leakage current at 125°C,
12.5 times or less than 20°C specified value.
Damp Heat
(Steady State)
At 40°C, 90 to 95% R.H., For 500hours (No voltage applied)
Capacitance Change
Refer to the table below (* 1)
Dissipation Factor
150% or less of initial specified value
Leakage Current
200% or less of initial specified value
Temperature Cycles
At --55°C / +125°C, For 30 minutes each, 5 cycles
Capacitance Change
Refer to the table below (* 1)
150% or less than the initial specified value
Dissipation Factor
Leakage Current
Initial specified value or less
Resistance to Soldering
Heat
10 seconds reflow at 260°C, 5 seconds immersion at 260°C
Capacitance Change
Refer to the table below (* 1)
Leakage Current
Initial specified value or less
Leakage Current
Initial specified value or less
Surge∗
After application of surge in series with a 1kΩ resistor at the
rate of 30 seconds ON, 30 seconds OFF, for 1000 successive
test cycles at 85°C, capacitors shall meet the characteristic
requirements listed below.
Refer to the table below (* 1)
Capacitance Change
Dissipation Factor
150% or less than the initial specified value
Leakage Current
200% or less than the initial specified value
Endurance∗
After 1000 hours' application of rated voltage in series with a
3Ω resistor at 85°C, capacitors shall meet the characteristic
requirements table below
Capacitance Change
Refer to the table below (* 1)
Dissipation Factor
150% or less than the initial specified value
Leakage Current
200% or less than the initial specified value
Shear Test
After applying the pressure load of 5N
for 10±1 seconds horizontally to the
center of capacitor side body which has
no electrode and has been soldered
beforehand on a substrate, there shall be
found neither exfoliation
nor its sign at the terminal electrode.
Terminal Strength
Keeping a capacitor surface-mounted on a substrate upside
down and supporting the substrate at both of the opposite
bottom points 45mm apart from the center of capacitor, the
pressure strength is applied with
20
a specified jig at the center of the
R230
substrate so that substrate
may bend by 1mm as illustrated.
Then, there shall be found no
remarkable abnormality on the
45
45
capacitor terminals.
Type numbering system (Example : 6.3V 10µF)
1
2
3
4
5
6
7
8
9
10
F 9 8 0 J 1 0 6 M M
11
Taping code
(Refer to page 333 for details)
Case code
Capacitance tolerance
Rated capacitance Rated voltage
Series
Drawing
L
W1
H
W2
S1
S2
S1
(mm)
W2
W1
L
H
1.10 ± 0.05 0.60 ± 0.05 0.35 ± 0.05
U
+
0.55 ± 0.05 0.3 ± 0.05 0.5 ± 0.05
+0.2
M
0.2
1.6 -0.1
0.85 - 0.1 0.65 ± 0.1 0.8 ± 0.1 0.5 ± 0.1
S
+ 0.2
2.0 -0.1
1.25 - 0.1
+0.2
S2
S1
0.9 ± 0.1 0.8 ± 0.1 0.5 ± 0.1
0.6 ± 0.1
1.0 ± 0.1
1mm
Case Code
Marking
U Case
M Case
Capacitance code
S Case
J
∗ As for the surge voltage, refer to page 332 for details.
Js
Rated voltage
(Voltage code)
Cap.(µF)
Code
1
105
2.2
225
4.7
475
10
22
4
0G
6.3
0J
10
1A
16
1C
20
1D
25
1E
Capacitance
code
M
M
M
---
U•M
M
---
(U) • M
M
---
S
a
U
U•M
106
U
(U) • M
M
226
M
M
(M) • S
J
33
336
M
M
(M) • S
n
47
476
M
M S
S
68
686
M
•
S
100
107
M
•
S
220
227
•
S
( ) The series in parentheses are being developed.
Please contact to your local Nichicon sales office when
these series are being designed in your application.
We can consider the type of compliance to AEC-Q200.
Please contact to your local Nichicon sales office
when these series are being designed in your application.
(Ω@100kHz)
ESR
*1 ∆C/C
(%)
F980G475MUA
F980G106MUA
F980G226MMA
F980G336MMA
F980G476MMA
F980G686MMA
F980G686MSA
F980G107MMA
F980G107MSA
F980G227MSA
0.5
0.8
0.9
1.3
1.9
27.2
2.7
80.0
4.0
132
20
25
15
30
40
50
30
60
35
80
20
20
7.5
4
8
10
4
10
4
5
±30
±30
±30
±30
±30
±30
±30
±30
±30
±30
F980J475MUA
F980J475MMA
F980J106MMA
F980J226MMA
F980J336MMA
F980J476MMA
F980J476MSA
F980J107MSA
F981A225MUA
F981A225MMA
F981A475MMA
F981A106MMA
F981A226MSA
F981A336MSA
F981A476MSA
F981C105MMA
F981C225MMA
F981C475MMA
F981C106MSA
F981D105MMA
F981E105MMA
0.6
0.5
0.6
1.4
4.2
29.6
3.0
63.0
0.5
0.5
0.5
1.0
2.2
3.3
9.4
0.5
0.5
0.8
1.6
0.5
0.5
20
20
8
20
35
45
25
50
15
6
6
20
20
30
35
6
6
12
18
6
8
20
7.5
6
6
8
10
6
8
15
7.5
6
7.5
4
6
5
10
10
12
4
10
10
±30
±30
±30
±30
±30
±30
±30
±30
±30
±30
±30
±30
±20
±30
±30
±30
±30
±30
±20
±30
±30
Case
code
Part Number
4V
4.7
10
22
33
47
68
68
100
100
220
U
U
M
M
M
M
S
M
S
S
4.7
4.7
10
22
33
47
47
100
2.2
2.2
4.7
10
22
33
47
1
2.2
4.7
10
1
1
U
M
M
M
M
M
S
S
U
M
M
M
S
S
S
M
M
M
S
M
M
6.3V
s
A
Disspation
Factor
(% @120Hz)
Rated
Capacitance
(µF)
w
S
Current
(µA)
Rated Volt
Rated voltage
(Voltage code)
Standard Ratings
V
5N (0.51kg • f)
For 10 ± 1 seconds
10V
J
16V
20V
25V
*2 Leakage
*2 : Leakage Current
After 5 minute's application of rated voltage, leakage current at 20˚C.
CAT.8100B