F98-AS1 Series Fused Face-Down, High CV FEATURES • Compliant to the RoHS2 directive 2011/65/EU APPLICATIONS LEAD-FREE COMPATIBLE COMPONENT • Industrial equipment • Smartphone • Medical equipment • Automotive electronics • Portable game CASE DIMENSIONS: millimeters (inches) Code EIA Code EIA Metric M 0603 S 0805 L L 1608-09 1.60 (0.063 2012-09 2.00 (0.079 W1 +0.20 -0.10 +0.008 -0.004 +0.20 -0.10 +0.008 -0.004 ) 0.85 (0.033 ) 1.25 (0.049 +0.20 -0.10 +0.008 -0.004 +0.20 -0.10 +0.008 -0.004 W2 H S1 W2 ) 0.65±0.10 (0.026±0.004) 0.80±0.10 (0.031±0.004) 0.50±0.10 (0.020±0.004) 0.60±0.10 (0.024±0.004) ) 0.90±0.10 (0.035±0.004) 0.80±0.10 (0.031±0.004) 0.50±0.10 (0.020±0.004) 1.00±0.10 (0.039±0.004) MARKING W1 H M CASE S CASE An E W2 S1 S2 Rated Voltage Code S1 HOW TO ORDER F98 1A 336 Type Rated Voltage Capacitance Code pF code: 1st two digits represent significant figures, 3rd digit represents multiplier (number of zeros to follow) *Capacitance Code Rated Voltage Code M S Tolerance M = ±20% Case Size See table above ⵧ AS1 Packaging Fuse Series Code Reel Dia (φ180) A Tape Width (mm) 8 TECHNICAL SPECIFICATIONS Category Temperature Range: Rated Temperature: Capacitance Tolerance: Dissipation Factor: ESR 100kHz: Leakage Current: 70 -55 to +125°C +85°C ±20% at 120Hz Refer to next page Refer to next page Refer to next page Provided that: After 5 minute’s application of rated voltage, leakage current at 85°C 10 times or less than 20ºC specified value. After 5 minute’s application of rated voltage, leakage current at 125°C 12.5 times or less than 20ºC specified value. 030116 F98-AS1 Series Fused Face-Down, High CV CAPACITANCE AND RATED VOLTAGE RANGE (LETTER DENOTES CASE SIZE) Capacitance µF Code 1.0 105 2.2 225 4.7 475 10 106 22 226 33 336 47 476 10V (1A) M* M* M* M*/S M*/S S Rated Voltage 20V (1D) M* 16V (1C) M* M* M* S Available Ratings *Codes under development – subject to change 25V (1E) M* 35 (1V) S *Cap Code A – – a J n – Please contact to your local AVX sales office when these series are being designed in your application. RATINGS & PART NUMBER REFERENCE AVX Part No. Case Capacitance Size (μF) F981A226MSAAS1 F981A336MSAAS1 F981A476MSAAS1 S S S F981C106MSAAS1 S F981V105MSAAS1 S Rated Voltage (V) 10 Volt 10 10 10 16 Volt 10 16 35 Volt 1 35 22 33 47 *2 DCL (μA) DF ESR @ 120Hz @ 100kHz (%) (Ω) *1 ΔC/C (%) 2.2 3.3 9.4 20 30 35 4.5 6.5 5.5 ±20 ±30 ±30 1.6 18 4.5 ±20 0.7 20 8.5 ±30 *2: Leakage Current After 5 minute’s application of rated voltage, leakage current at 20ºC. QUALIFICATION TABLE TEST Damp Heat (Steady State) Temperature Cycles Resistance to Soldering Heat Surge Endurance Shear Test Terminal Strength Fuse activation F98-AS1 series (Temperature range -55ºC to +125ºC) Condition At 40°C, 90 to 95% R.H., 500 hours (No voltage applied) Capacitance Change ........... Refer to the table above (*1) Dissipation Factor ................ 150% or less of initial specified value Leakage Current .................. 200% or less of initial specified value -55°C / +125°C, 30 minutes each, 5 cycles Capacitance Change ........... Refer to the table above (*1) Dissipation Factor ................ 150% or less of initial specified value Leakage Current .................. 200% or less of initial specified value 10 seconds reflow at 260°C, 5 seconds immersion at 260°C. Capacitance Change ........... Refer to the table above (*1) Dissipation Factor ................ Initial specified value or less Leakage Current .................. Initial specified value or less After application of surge in series with a 1kΩ resistor at the rate of 30 seconds ON, 30 seconds OFF, for 1000 successive test cycles at 85ºC, capacitors shall meet the characteristic requirements in the table above. Capacitance Change ........... Refer the table above (*1) Dissipation Factor ................ 150% or less of initial specified value Leakage Current .................. 200% or less of initial specified value After 1000 hours’ application of rated voltage in series with a 3Ω resistor at 85°C, capacitors shall meet the characteristic requirements in the table above. Capacitance Change ........... Refer to the table above (*1) Dissipation Factor ................ 150% or less of initial specified value Leakage Current .................. 200% or less of initial specified value After applying the pressure load of 5N for 10±1 seconds horizontally to the center of capacitor side body which has no electrode and has been soldered beforehand on a substrate, there shall be found neither exfoliation nor its sign at the terminal electrode. Keeping a capacitor surface-mounted on a substrate upside down and supporting the substrate at both of the opposite bottom points 45mm apart from the center of capacitor, the pressure strength is applied with a specified jig at the center of substrate so that the substrate may bend by 1mm as illustrated. Then, there shall be found no remarkable abnormality on the capacitor terminals. 5 seconds max. with 2A min. applied current NOTICE: DESIGN, SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. 030116 71