QF-XMS Series 0.25W, FIXED INPUT, ISOLATED&UNREGULATED SINGLE OUTPUT DC-DC CONVERTER PRODUCT PROGRAM Model Input Voltage (V) Output Voltage (V) Output Current max (MA) Isolation (VDC) Max Capacitive Load (uF) EQFQFici ency (%) QF0503XMS 4.5-5.5 3.3 75.7 3000 100 66 QF0505XMS 4.5-5.5 5 50 3000 100 66 QF0507XMS 4.5-5.5 7.2 34.72 3000 100 66 QF0509XMS 4.5-5.5 9 27.77 3000 100 68 QF0512XMS 4.5-5.5 12 20.83 3000 100 68 QF0515XMS 4.5-5.5 15 16.67 3000 100 68 QF0518XMS 4.5-5.5 18 13.88 3000 100 68 QF0524XMS 4.5-5.5 24 10.41 3000 100 70 QF1203XMS 10.8-13.2 3.3 75.7 3000 100 66 QF1205XMS 10.8-13.2 5 50 3000 100 67 QF1207XMS 10.8-13.2 7.2 34.72 3000 100 68 QF1209XMS 10.8-13.2 9 27.77 3000 100 68 QF1212XMS 10.8-13.2 12 20.83 3000 100 68 QF1215XMS 10.8-13.2 15 16.67 3000 100 69 QF1218XMS 10.8-13.2 18 13.88 3000 100 70 APPLICATIONS QF1224XMS 10.8-13.2 24 10.41 3000 100 72 1. Datasheets are updated as needed and as such, pecifications QF2403XMS 21.6-26.4 3.3 75.7 3000 100 67 QF2405XMS 21.6-26.4 5 50 3000 100 67 QF2407XMS 21.6-26.4 7.2 34.72 3000 100 67 QF2409XMS 21.6-26.4 9 27.77 3000 100 69 QF2412XMS 21.6-26.4 12 20.83 3000 100 69 QF2415XMS 21.6-26.4 15 16.67 3000 100 69 QF2418XMS 21.6-26.4 18 13.88 3000 100 69 QF2424XMS 21.6-26.4 24 10.41 3000 100 69 FEATURES ◆ RoHS compliant ◆ 4 Pin SIP Package ◆ Low ripple and noise ◆ High efficiency up to 72% ◆ Operating temperature -40℃ to +85℃ ◆ Input/Output isolation 3000VDC ◆ Pin compatible with multiple manufacturers MODEL SELECTION ① ② ③ ④ ⑤ QF 05 03 X MS ①Product Series ③Output Voltage ⑤SIP4 Package ②Input Voltage ④Fixed Input are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by microdc; refer to www.microdc.cn for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%,nominal input voltage and at rated output load unless otherwise specified. 5. microdc may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with microdc’s Standard Terms of Sale available at www.microdc.cn. MICRODC R ESERVES THE COPYRIGHT http://www.microdc.cn Technical Enquiries-Email:[email protected] Tel:0086-20-86000646 Page 1 of 3 QF-XMS Series Input Specifications Parameters Nominal Voltage range Typical 5 4.5-5.5 12 10.8-13.2 15 13.5–16.5 24 21.6-26.4 Filter Maximum Units VDC Capacitor Turn on transient process time 25 Start up time 200 Absolute maximum rating 5 Vin 7 12 Vin 15 15 Vin 17 24 Vin 28 Peak input voltage time ms ms VDC 100 ms General Specifications Parameters Conditions Typical Switching frequency 100% load 80 Operating temperature Without derating Maximum Units KHz Storage temperature -40～+85 ℃ -40～+125 ℃ Maximum case temperature Cooling 100 ℃ 95 % F g Free air convection Humidity Case material Non-conductive black plastic Weight 1.5 Dimensions (Lx W x H) 0.46 x 0.24 x 0.38 inches 11.68 x 6.00 x 9.65 mm >2 010 000 hrs (MIL-HDBK -217F, Ground Benign, t=+25 ℃) MTBF NOTE: All specifications in this data sheet are measured at an ambient temperature of 25° 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. specified. Output Specifications Parameters Conditions Voltage accuracy Typical Maximum ±3 Short circuit protection Units % Momentary (1sec) Line voltage regulation For 1% change of Vin ±1.2 % of Vin Load voltage regulation Load 20 – 100% ±10 % Load 20 – 100% ±20 % ±0.02 %/ C 100 mV p-p Load voltage regulation 3.3V output model Temperature coefficient Ripple & noise At 20MHz Bandwidth Capacitive load Rising time http://www.microdc.cn 100 50 Technical Enquiries-Email:[email protected] Tel:0086-20-86000646 μF ms Page 2 of 3 QF-XMS Series Isolation Specifications Parameters Conditions Tested I/O voltage 3 sec Typical Rated Units 3000 VDC Resistance > 1000 MOhm Capacitance 60 pF Recommended footprint details TUBE OUTLINE DIMENSIONS 4 PIN SIP Package 4 PIN SIP Tube Unless otherwise stated all dimensions in inches (mm) ±0.5mm. Tube length (4 Pin SIP) : 20.47 (520mm ±2mm). Dimensions Pin Out Specifications Microdc Professional Power Module,Inc. Tel:0086-20-86000646 E-mail:[email protected] Pin Single 1 - V Input 2 +V Input 3 - V Output 4 +V Output RoHS COMPLIANT INFORMATION This series is compatible with RoHS soldering systems with a peak wave solder temperature of 300°C for 10 seconds. The pin termination finish on the SIP package type is Tin Plate, Hot Dipped over Matte Website:http://www.microdc.cn Microdc Professional Power module,Inc.makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. Specifications are subject to change without notice. ©2010 Tube Quantity :25 Microdc Professional Power Module, Inc. Guangzhou Tin with Nickel Preplate. The DIP types are Matte Tin over Nickel Preplate. Both types in this series are backward compatible with Sn/Pb soldering systems. REACH COMPLIANT INFORMATION This series has proven that this product does not contain harmful chemicals, it also has harmful chemical substances through the registration, inspection and approval. http://www.microdc.cn Technical Enquiries-Email:[email protected] Tel:0086-20-86000646 Page 3 of 3