SURFACE MOUNT PHOTODIODE WITH DAYLIGHT FILTER ODD-900-001 Dimensions are in metric [inch] units FEATURES • Daylight filter • High sensitivity • Low capacitance • Short switching time • Surface mount package ELECTRO-OPTICAL CHARACTERISTICS AT 25°C PARAMETERS Range of Spectral Bandwidth, λ 0.5 Wavelength of Peak Sensitivity, λ P Responsivity Reverse Dark Current, I P Reverse Breakdown Voltage, B VR Total Capacitance, C t Rise/Fall Time, t r/tf THERMAL PARAMETERS RoHS TEST CONDITIONS MIN TYP MAX UNITS λ p = 940nm VR = 10V IR = 100µA VR = 3V, f = 1MHz VR = 10V, R L = 1KΩ 730 32 - 940 0.44 5 170 25 50/50 1100 - nm nm A/W nA Volts pF nSec Operating Temperature Range Storage Temperature Range Power Dissipation at (or below) 25°C Free Air Temperature Soldering Temperature 1 (Soldering time 5 sec max.) - -25°C TO +85°C -40°C TO +85°C 150mW 260°C 1260 Calle Suerte, Camarillo, California 93012 Phone: (805) 499-0335, Fax: (805) 499-8108 Email: [email protected], Website: www.optodiode.com Revision February 26, 2013 RELATIVE SPECTRAL SENSITIVITY SURFACE MOUNT PHOTODIODE WITH DAYLIGHT FILTER 1.0 REVERSE DARK CURRENT (nA) SPECTRAL SENSITIVITY Ta = 25°C 0.8 0.6 0.4 0.2 0.0 1000 600 700 800 900 1000 WAVELENGTH λ (nm) 1100 1200 DARK CURRENT vs AMBIENT TEMPERATURE 100 10 1 80 TERMINAL CAPACITANCE (pF) ODD-900-001 VR = 10V 20 40 60 80 AMBIENT TEMPERATURE Ta (°C) 100 TERMINAL CAPACITANCE vs REVERSE VOLTAGE f = 1MHz VR = 3V Ee = 0mW/cm2 60 40 20 0 0.1 1 10 100 REVERSE VOLTAGE (V) 1260 Calle Suerte, Camarillo, California 93012 Phone: (805) 499-0335, Fax: (805) 499-8108 Email: [email protected], Website: www.optodiode.com Revision February 26, 2013 128 SURFACE MOUNT PHOTODIODE WITH DAYLIGHT FILTER 1 ODD-900-001 Soldering Conditions 1.0 Pb-free solder temperature profile 260°C Max 10 sec Max 1~5°C/sec Pre-heating 180~200°C 1~5°C/sec 60 sec Max Above 220°C 120 sec Max 2.0 1.1 Reflow soldering should not be done more than twice 1.2 Do not stress the PD while soldering 1.3 Don’t flex the circuit board after soldering Soldering Iron 2.1 Each terminal should touch the tip of soldering iron (at 280°C) for less than for three seconds. Use a minimum two second interval between soldering each terminal. Use caution as product damage is often started during hand soldering. 2.2 The tip of soldering iron (at 280°) should be in contact with each terminal for less than three seconds. Pause for a minimum two second interval between soldering each terminal. Use caution as damage to the PD is often started during hand soldering. 1260 Calle Suerte, Camarillo, California 93012 Phone: (805) 499-0335, Fax: (805) 499-8108 Email: [email protected], Website: www.optodiode.com Revision February 26, 2013 SURFACE MOUNT PHOTODIODE WITH DAYLIGHT FILTER ODD-900-001 1260 Calle Suerte, Camarillo, California 93012 Phone: (805) 499-0335, Fax: (805) 499-8108 Email: [email protected], Website: www.optodiode.com Revision February 26, 2013