M0220MD‐202MDAR1‐3 Dot‐matrix Character Vacuum Fluorescent Display Module M‐ 0220‐ M‐ D‐ 202MDA‐ R‐ 1‐3 VFD Module 2 lines x 20 characters Model Dot‐Matrix Character size = 3.68mm x 8.78mm RoHS Compliant Parallel interface (M6800) Newhaven Display International, Inc. 2511 Technology Drive, Suite 101 Elgin IL, 60124 Ph: 847‐844‐8795 Fax: 847‐844‐8796 www.newhavendisplay.com [email protected] [email protected] Document Revision History Revision 0 1 2 Date 3/21/2005 9/21/2009 12/4/2009 Description Initial Release Updated Driver version, modified vf glass pins Reduce pixel size to increase brightness and lifetime Functions and Features • • • • • • 2 lines x 20 characters Built‐in controller Built‐in VF AC power supply 5.0V power supply 5x8 dots with cursor Parallel interface (Serial interface selectable by jumpers) Changed by CL CL Mechanical Drawing Pattern Detail Pin Description (parallel interface) Pin No. Symbol 1 2 3 4 5 6 7‐10 VSS VDD NC (/RST) RS R/W E DB0 – DB3 11‐14 DB4 – DB7 External Connection Power Supply Power Supply ‐ (MPU) MPU MPU MPU MPU MPU Function Description Ground Power supply for logic (+5.0V) No Connect (if JP2 is short, PIN3 = Active LOW reset signal) Register select signal RS=1: DATA RS=0: COMMAND Read/Write select signal RW=1: READ RW=0: WRITE Operation enable signal Falling Edge Triggered Four low order bi‐directional three‐state data bus lines. These four are not used during 4‐bit operation Four high order bi‐directional three‐state data bus lines. Recommended LCD connector: 2.54mm pitch pins Pin Description (optional serial interface) Pin No. Symbol 1 2 3 4 5 6 7‐14 VSS VDD SI/SO STB NC SCK NC External Connection Power Supply Power Supply MPU MPU ‐ MPU ‐ Function Description Ground Power supply for logic (+5.0V) Serial Data In, data out Serial Strobe signal No Connect Serial Clock signal No Connect Recommended LCD connector: 2.54mm pitch pins Jumper Settings (Default Parallel M68 mode) Mode JP2 JP3 JP4 JP5 JP6 JP7 Serial Open Short Open Short Open Short Parallel (I80) *1 Open Short Open Open Short Parallel (M68) *1 Open Short Open Short Open *1) JP2 short enables PIN3 as external reset. JP2 open disables reset. Block Diagram Electrical Characteristics Item Operating Temperature Range Storage Temperature Range Operating Humidity Storage Humidity Vibration Shock Supply Voltage Supply Current (*Note) Luminance “H” Level input “L” Level input “H” Level output “L” Level output Symbol Vop Vst Hop Hst VDD IDD L Vih Vil Voh Vol Condition 10~55Hz Ta=25°C VDD=5.0V Min. -40 -50 0 0 4.5 - Typ. 5.0 290 Max. +85 +95 85 90 4 40 5.5 435 Unit ⁰C ⁰C % % G G V mA 350 2.2 0 2.4 - 500 - VDD 0.6 0.4 cd/m2 V V V V *Note: In-rush current can be approx 10 times the specified supply current at power up. Power-on Timing Controller Information Built-in PT6314 controller. Download specification at http://www.newhavendisplay.com/app_notes/PT6314.pdf Table of Commands M68 Parallel Interface: The PT6314 can interface with the CPU in 4‐bits or 8‐bits. Note that the internal registers are composed of 8 bits. During data transfer in 4‐bit mode, DB4‐DB7 performs the data transfer operation two times, DB0‐DB3 should be tied HIGH or LOW. 4‐bit Data Transfer (M68): 8‐bit Data Transfer (M68): Built‐in Font Table Example Initialization after Power ON Quality Information Test Item Content of Test High Temperature storage Endurance test applying the high storage temperature for a long time. Endurance test applying the low storage temperature for a long time. Endurance test applying the electric stress (voltage & current) and the high thermal stress for a long time. Endurance test applying the electric stress (voltage & current) and the low thermal stress for a long time. Endurance test applying the electric stress (voltage & current) and the high thermal with high humidity stress for a long time. Endurance test applying the electric stress (voltage & current) during a cycle of low and high thermal stress. Endurance test applying vibration to simulate transportation and use. Low Temperature storage High Temperature Operation Low Temperature Operation High Temperature / Humidity Operation Thermal Shock resistance Vibration test Static electricity test Endurance test applying electric static discharge. Test Condition 2 ‐30⁰C , 48hrs 1,2 +70⁰C 48hrs 2 ‐20⁰C , 48hrs 1,2 +40⁰C , 90% RH , 48hrs 1,2 0⁰C,30min ‐> +25⁰C,5min ‐> +50⁰C,30min = 1 cycle 10 cycles 10‐55Hz , 15mm amplitude. 60 sec in each of 3 directions X,Y,Z For 15 minutes VS=800V, RS=1.5kΩ, CS=100pF One time Note 1: No condensation to be observed. Note 2: Conducted after 4 hours of storage at 25⁰C, 0%RH. Note 3: Test performed on product itself, not inside a container. Precautions for using LCDs/LCMs See Precautions at www.newhavendisplay.com/specs/precautions.pdf Warranty Information and Terms & Conditions http://www.newhavendisplay.com/index.php?main_page=terms Note +80⁰C , 48hrs 3