NHD‐C12864WM‐09‐FSW‐FBW‐3V3‐M COG (Chip‐On‐Glass) Liquid Crystal Display Module NHD‐ C12864‐ WM‐ F‐ SW‐ F‐ B‐ W‐ 3V3‐ M‐ Newhaven Display 128 x 64 pixels Model Transflective Side White LED backlight FSTN (+) 6:00 view Wide Temp (‐20°C ~ +70°C) 3Vdd, 3Volt Backlight Mounting Holes RoHS Compliant Newhaven Display International, Inc. 2511 Technology Drive, Suite 101 Elgin IL, 60124 Ph: 847‐844‐8795 Fax: 847‐844‐8796 www.newhavendisplay.com [email protected] [email protected] [1] Document Revision History Revision 0 1 2 3 4 5 Date 1/22/2007 8/7/2009 10/13/2009 2/16/2010 2/19/2010 5/14/2010 Description Initial Release User guide reformat Updated Electrical Characteristic Mechanical drawing updated Block diagram updated Electrical Characteristic update Functions and Features • • • • • 128 x 64 pixels Built‐in SPLC501C controller Parallel/Serial mode 1/64 duty cycle; 1/9 bias RoHS Compliant [2] Changed by ‐ BE MC BE BE MP Front Back Specification: 1). Driving: Duty: 1/64, 1/9 Bias, Vlcd: 9.5V 2). Viewing Direction: 6 O’Clock 3). Display mode: FSTN/Positive/Transflective 4). Operating Temp.: -20 oC ~ +70oC Storage Temp.: -30 oC ~ +80oC 5). Driver: SPL5010C 6). Unmarked Tolerances: + 0.2mm 7). Backlight: Side White NHD-C12864WM-09-FSW-FBW-3V3-M Newhaven Display Pin Description and Wiring Diagram Pin No. Symbol 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 A K CS2 RESETB RS RW E DB0 DB1 DB2 DB3 DB4 DB5 DB6 DB7 VSS2 VOUT CAP3‐ CAP1+ CAP1‐ CAP2‐ CAP2+ VSS VDD V1 V2 V3 V4 V5 VR C86 PS External Connection MPU MPU MPU MPU MPU MPU MPU MPU MPU MPU MPU MPU MPU Power Supply Power Supply Power Supply Power Supply Power Supply Power Supply Power Supply Power Supply Power Supply Power Supply Power Supply Power Supply Power Supply Power Supply ‐ MPU MPU Power Supply Power Supply Function Description Active HIGH chip select Active LOW Reset signal Register select signal. RS=0: Command, RS=1: Data Read/write select signal. R/W=1: Read R/W=0: Write Operation enable signal. Falling edge triggered. Parallel Interface DB0‐DB7: Bi‐directional 8‐bit data bus Serial Interface: DB0‐DB5: No connect in serial mode DB6= Serial clock (CLK) DB7= Serial data input (SDA) Ground (reference for voltage step‐up circuit) Connect to 1uF cap to VSS2 (PIN‐14) Connect to 1uF cap to CAP1+ (PIN‐17) Connect to 1uF cap to CAP3‐(PIN16) and CAP1‐(PIN18) Connect to 1uF cap to CAP1+ (PIN‐17) Connect to 1uF cap to CAP2+ (PIN‐20) Connect to 1uF cap to CAP2‐ (PIN‐19) Ground Power supply for LCD and logic (3.0V) 1.0uF‐2.2uF cap to VDD 1.0uF‐2.2uF cap to VDD 1.0uF‐2.2uF cap to VDD 1.0uF‐2.2uF cap to VDD 1.0uF‐2.2uF cap to VDD No Connect Select MPU interface pin. C86=H: 6800; C86=L: 8080 Parallel/Serial select. PS= H: Parallel; PS=L: Serial Power supply for LED Backlight (+3.0V) Ground for Backlight Recommended LCD connector: 0.5mm Pitch, 30 pin FFC. Molex p/n: 52892‐3095 Backlight connector: A2001H‐2P Mates with: A2001WR‐S‐2P [4] Electrical Characteristics Item Operating Temperature Range Storage Temperature Range Supply Voltage Supply Current Supply for LCD (contrast) “H” Level input “L” Level input “H” Level output “L” Level output LED Backlight voltage LED Backlight current Symbol TOP TST VDD IDD Condition Absolute Max Absolute Max Min. ‐20 ‐30 2.4 0.6 ‐ 0.7VDD Vss ‐ ‐ Typ. ‐ ‐ 3.3 ‐ ‐ ‐ ‐ ‐ ‐ VDD-V0 - Vih Vil VLED ILED ‐ VLED=3.0 ‐ ‐ Condition CR 2 CR 2 Min. ‐60 ‐40 ‐ ‐ ‐ VDD=3.3v 3.0 10 Max. +70 +80 5.5 1.0 9.5 VDD 0.3VDD ‐ ‐ 3.5 20 Unit ⁰C ⁰C V mA V V V ‐ ‐ V mA Typ. ‐ 6 150 150 Max. +35 +40 ‐ 250 250 Unit ⁰ ⁰ ‐ ms ms Optical Characteristics Item Viewing Angle ‐ Vertical Viewing Angle ‐ Horizontal Contrast Ratio Response Time (rise) Response Time (fall) Symbol θ Φ CR Tr Tf [5] Controller Information Built‐in SPLC501C. Download specification at http://www.newhavendisplay.com/app_notes/SPLC501C.pdf [6] [7] Table of Commands [8] [9] Example Initialization Program '‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐ Sub Init Reset P3.7 'set Read/write to '0' for write Reset P3.0 'RS Set P3.1 'reset Reset P3.4 'E 'Set P3.3 'Reset P3.3 Waitms 2 'Set P3.3 Waitms 20 A = &HA2 '1/9 BIAS Call Writecom A = &HA0 'ADC SELECT , NORMAL Call Writecom A = &HC8 'COM OUTPUT REVERSE Call Writecom A = &HA4 'DISPLAY ALL POINTS NORMAL Call Writecom A = &H40 'DISPLAY START LINE SET Call Writecom A = &H25 'INTERNAL RESISTOR RATIO Call Writecom A = &H81 'ELECTRONIC VOLUME MODE SET Call Writecom A = &H10 'ELECTRONIC VOLUME Call Writecom A = &H2F 'POWER CONTROLLER SET Call Writecom A = &HAF 'DISPLAY ON Call Writecom End Sub '‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐ Sub Writecom Reset P3.0 'A0 low Reset P3.7 'R/W low Set P3.6 'CS2 Set P3.4 'E P1 = A Reset P3.4 Reset P3.6 Reset P3.7 End Sub Sub Writedata Set P3.0 'A0 high Reset P3.7 'R/W low Set P3.6 'CS2 Set P3.4 'E P1 = A Reset P3.4 Reset P3.6 Reset P3.7 End Sub '‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐ [10] Quality Information Test Item Content of Test High Temperature storage Endurance test applying the high storage temperature for a long time. Endurance test applying the low storage temperature for a long time. Endurance test applying the electric stress (voltage & current) and the high thermal stress for a long time. Endurance test applying the electric stress (voltage & current) and the low thermal stress for a long time. Endurance test applying the electric stress (voltage & current) and the high thermal with high humidity stress for a long time. Endurance test applying the electric stress (voltage & current) during a cycle of low and high thermal stress. Endurance test applying vibration to simulate transportation and use. Low Temperature storage High Temperature Operation Low Temperature Operation High Temperature / Humidity Operation Thermal Shock resistance Vibration test Static electricity test Test Condition Endurance test applying electric static discharge. 2 ‐30⁰C , 48hrs 1,2 +70⁰C 48hrs 2 ‐20⁰C , 48hrs 1,2 +40⁰C , 90% RH , 48hrs 1,2 ‐0⁰C,30min ‐> 25⁰C,5min ‐> 50⁰C,30min = 1 cycle 10 cycles 10‐55Hz , 15mm amplitude. 60 sec in each of 3 directions X,Y,Z For 15 minutes VS=800V, RS=1.5kΩ, CS=100pF One time Note 1: No condensation to be observed. Note 2: Conducted after 4 hours of storage at 25⁰C, 0%RH. Note 3: Test performed on product itself, not inside a container. Precautions for using LCDs/LCMs See Precautions at www.newhavendisplay.com/specs/precautions.pdf Warranty Information and Terms & Conditions http://www.newhavendisplay.com/index.php?main_page=terms [11] Note +80⁰C , 48hrs 3