DC-DC Converter SIP-Package DBE-1 SERIES, 1WATT, 1KVDC, UNREGULATED FEATURES: 1000Vdc isolation voltage Compact size Operating temperature range -40 3 year warranty Model Input voltage (Vdc) ℃ to +85 ℃ Output voltage (Vdc) Output current (mA) Min. Max. Efficiency Typ. DBE1-0310 3.3 30 300 80% DBE1-0311 5 20 200 80% 9 11 110 80% 12 8.3 83 80% DBE1-0314 15 6.8 68 80% DBE1-0315 24 4.2 42 80% DBE1-0510 3.3 30 300 80% DBE1-0511 5 20 200 80% 9 11 110 80% 12 8.3 83 80% DBE1-0514 15 6.8 68 80% DBE1-0515 24 4.2 42 80% DBE1-1210 3.3 30 300 80% DBE1-1211 5 20 200 80% 9 11 110 80% 12 8.3 83 80% DBE1-1214 15 6.8 68 80% DBE1-1215 24 4.2 42 80% DBE1-2410 3.3 30 300 80% DBE1-2411 5 20 200 80% 9 11 110 80% 12 8.3 83 80% DBE1-2414 15 6.8 68 80% DBE1-2415 24 4.2 42 80% DBE1-0312 DBE1-0313 DBE1-0512 DBE1-0513 DBE1-1212 DBE1-1213 DBE1-2412 DBE1-2413 3.3(2.97~3.63) 5(4.5~5.5) 12(10.8~13.2) 24(21.6~26.4) Notes: 1. other input and output models may available on request; 2. Add suffix “P” for short circuit protection. www.pairuigroup.com Page: 1/3 Date: 12/06/2014 DC-DC Converter SIP-Package DBE-1 SERIES, 1WATT, 1KVDC, UNREGULATED ELECTRICAL Output voltage accuracy --- ±5% max. Line regulation --- ± 1.2% Load regulation 10% ~ 100% full load Switching frequency --- 100KHz Ripple and noise --- 100mVp-p max. Isolation voltage --- 1000Vdc Short circuit protection Only available for "DBE1-xx1xP" product Operating temperature range --- Storage temperature range 5%~95%, non-condensing Temperature coefficient --- MTBF MIL-HDBK-217F@25 Weight --- 15% max. Continuous, auto-recovery ℃ to +85℃ -40℃ to +85℃ ±0.03%/℃ -40 ℃ 3500KHrs 1.3g Notes: All the parameters are measured at 25℃ ambient temperature, humidity < 75%, nominal input voltage, full load and after warm-up, unless otherwise specified. MECHANICAL CONNECTION PIN # SINGLE 1 GND 2 +Vin 3 -Vo 4 +Vo Note: * Unit is mm(inch). TEMPERATURE PROFILE www.pairuigroup.com Page: 2/3 Date: 12/06/2014 DC-DC Converter SIP-Package DBE-1 SERIES, 1WATT, 1KVDC, UNREGULATED CAPACITIVE LOADS SELECTION Single Output Cin (Vdc) (μF) 3.3/5 4.7 5 10 ±5 4.7 12 2.2 9 4.7 ±9 2.2 24 1 12 2.2 ±12 1 - - 15/24 1 ±15 0.47 Voltage Cout Dual Output Vin (μF) (Vdc) Cout Voltage (μF) (Vdc) NOTES RECOMMENDED TEST AND APPLICATION CIRCUIT In order to ensure the efficiency and dependability of the module, the minimum specified load must be less than 10% of rated load. If the output power is low, we recommend to add an external 10% loading resistor in parallel. FUSE: depends on the actual input current; TVS: depends on the actual input voltage; Recommended capacitor:C1, C2, C5,about 0.1uF; for C6,C7,please check the capacitive load; C3,C4:2KV/1nF. www.pairuigroup.com Page: 3/3 Date: 12/06/2014