DC-DC Converter SIP-Package DBV-1 SERIES, 1WATT, REGULATED WITH 2:1 INPUT RANGE FEATURES: Wide (2:1) input voltage range 1500Vdc isolation voltage Regulated isolated twin output models Continuous short circuit protection Operating temperature range -40 3 year warranty Model Input voltage (Vdc) ℃ to +85 ℃ Output voltage (Vdc) Output current (mA) Min. Max. Efficiency Typ. DBV1-0501 5, 5 10 100 80% DBV1-0502 9, 9 5.5 55 80% 12, 12 4.0 40 80% DBV1-0504 15, 15 3.3 33 80% DBV1-0505 24, 24 2.1 21 80% DBV1-1201 5, 5 10 100 80% DBV1-1202 9, 9 5.5 55 80% 12, 12 4.0 40 80% DBV1-1204 15, 15 3.3 33 80% DBV1-1205 24, 24 2.1 21 80% DBV1-2401 5, 5 10 100 80% DBV1-2402 9, 9 5.5 55 80% 12, 12 4.0 40 80% DBV1-2404 15, 15 3.3 33 80% DBV1-2405 24, 24 2.1 21 80% DBV1-0503 DBV1-1203 DBV1-2403 5(4.5~9) 12(9~18) 24(18~36) Notes: other input and output models may available on request. ELECTRICAL Line regulation --- ±0.2% Load regulation 10% ~ 100% full load ±0.5% Ripple and noise --- 100mVp-p max. Isolation voltage --- 1500Vdc Short circuit protection --- Continuous short circuit protection Operating temperature range --- MTBF --- 1000KHrs Weight --- 4.5g www.pairuigroup.com ℃ -40 Page: 1/3 to +85 ℃ Date: 07/31/2014 DC-DC Converter SIP-Package DBV-1 SERIES, 1WATT, REGULATED WITH 2:1 INPUT RANGE ELECTRICAL Notes: All the parameters are measured at 25℃ ambient temperature, humidity < 75%, nominal input voltage, full load and after warm-up, unless otherwise specified. MECHANICAL CONNECTION PIN # ISOLATED TWIN 1 GND 2 +Vin 6 +Vo1 7 -Vo1 8 CS 9 -Vo2 10 +Vo2 Note: * Unit is mm(inch). TEMPERATURE PROFILE www.pairuigroup.com Page: 2/3 Date: 07/31/2014 DC-DC Converter SIP-Package DBV-1 SERIES, 1WATT, REGULATED WITH 2:1 INPUT RANGE CAPACITIVE LOADS SELECTION Single Output Cin (Vdc) (μF) 5 4.7-100 5 560 ±5 270 12 4.7-100 9 470 ±9 220 24 4.7-100 12 470 ±12 220 - - 15/24 330 ±15/±24 150/100 Voltage Cout Dual Output Vin (μF) (Vdc) Voltage (Vdc) Cout (μF) NOTES RECOMMENDED TEST AND APPLICATION CIRCUIT In order to ensure the efficiency and dependability of the module, the minimum specified load must be less than 10% of rated load. If the output power is low, we recommend to add an external 10% loading resistor in parallel. FUSE: depends on the actual input current; TVS: depends on the actual input voltage; Recommended capacitor:C1, C2, C5,about 0.1uF; for C6,C7,C9, please check the capacitive load; C3,C4:2KV/1nF. www.pairuigroup.com Page: 3/3 Date: 07/31/2014