SM77D Series 3.3 V CMOS Clock Oscillators April 2014 • Pletronics’ SM77D Series is a quartz crystal controlled precision square wave generator with a CMOS output. • The SM77D series will directly interface TTL devices also. • The package is designed for high density surface m ount designs. • This is a low cost m ass produced oscillator. • Tape and Reel or cut tape packaging is available. • • • • 70 to 180 MHz 5 x 7 m m LCC Ceram ic Package Enable/Disable Function Disable function includes low standby power m ode • 3 rd Overtone Crystals used • Im proved circuit to m inim ize oscillator issues such as m ulti-m ode output signal. • Low Jitter • Capable of driving up to 50pF capacitive loads Pletronics Inc. certifies this device is in accordance with the RoHS 6/6 (2011/65/EC) and WEEE (2002/96/EC) directives. Pletronics Inc. guarantees the device does not contain the following: Cadm ium , Hexavalent Chrom ium , Lead, Mercury, PBB’s, PBDE’s W eight of the Device: 0.17 gram s Moisture Sensitivity Level: 1 As defined in J-STD-020C Second Level Interconnect code: e4 Absolute Maximum Ratings: Parameter Unit V CC Supply Voltage -0.5V to +7.0V Vi Input Voltage -0.5V to V CC + 0.5V Vo Output Voltage -0.5V to V CC + 0.5V Thermal Characteristics The m axim um die or junction tem perature is 155 oC The therm al resistance junction to board is 30 to 50 oC/W att depending on the solder pads, ground plane and construction of the PCB. P roduct inform ation is current as of publication date. T he product conform s to specifications per the term s of the P letronics standard warranty. Production processsing does not necessarily include testing of all param eters. Copyright © 2010, Pletronics Inc. SM77D Series 3.3 V CMOS Clock Oscillators April 2014 Part Number: SM77 45 D E V -125.0M -XX Packaging code or blank T250 = 250 per Tape and Reel T500 = 500 per Tape and Reel T1K = 1,000 per Tape and Reel Frequency in M Hz Supply Voltage V CC V = 3.3V _ + 10% Optional Enhanced OTR Blank = Tem p. range -10 to +70 oC C = Tem p. range -20 to +70 oC E = Tem p. range -40 to +85 oC Series M odel Frequency Stability 45 = + _ 50 ppm 44 = + _ 25 ppm 20 = + _ 20 ppm Series M odel Part Marking and Marking Legend: PLE SM 77 FF.FFF M C YMDxx PLE SM 77 FF.FFF M C YYWWxx 7xYW W xx FF.FFF M C PLE xxx PLE = Pletronics FF.FFF M = Frequency in MHz YYW W or YW W or YMD = Date of Manufacture (year and week, or year-m onth-day) All other m arking is internal factory codes Specifications such as frequency stability, supply voltage and operating tem perature range, etc. are not identified from the m arking. External packaging labels and packing list will correctly identify the ordered Pletronics part num ber. Codes for Date Code YM D Code 10 Code A 1 2 3 4 B C D E F G H J K L M Year 2010 2011 2012 2013 2014 Month JAN FEB MAR APR MAY JUN JUL AUG SEP OCT NOV DEC Code Day Code Day 1 1 H 17 2 2 J 18 www.pletronics.com 3 3 K 19 4 4 L 20 5 5 M 21 6 6 N 22 425-776-1880 7 7 P 23 8 8 R 24 9 9 T 25 A 10 U 26 B 11 V 27 C 12 W 28 D 13 X 29 E 14 Y 30 F 15 Z 31 2 G 16 SM77D Series 3.3 V CMOS Clock Oscillators April 2014 Electrical Specification for 3.30V + _ 10% over the specified temperature range Item Min Max Unit 70 180 MHz “45" -50 +50 ppm “44" -25 +25 “20" -20 +20 Frequency Range Frequency Accuracy Output Waveform Condition For all supply voltages, load changes, aging for 1 year, shock, vibration and temperatures CMOS Output High Level 90 - % Output Low Level - 10 % Output Symmetry 45 55 % - 0.6 pS RMS 12 KHz to 20 MHz from the output frequency - 2.5 pS RMS 10 Hz to 1 MHz from the output frequency 50 - Kohm V disable - 30 % V enable 70 - % -10 +10 uA -10 +10 uA Standby Current ICC - 3 uA Enable time - 2.0 mS Time for output to reach a logic state Disable time - 100 nS Time for output to reach a high Z state Start up time - 10 mS Time for output to reach specified frequency -10 +70 o C Standard Temperature Range -20 +70 o C Extended Temperature Range “C” Option -40 +85 o C Extended Temperature Range “E” Option -55 +125 o C Jitter Enable/Disable Internal Pull-up Output leakage VOUT = VCC VOUT = 0V Operating Temperature Range Storage Temperature Range of VCC (See load circuit) at 50% point of VCC (See load circuit) to VCC of VCC applied to pad 1 Pad 1 low, device disabled Typical phase-noise characteristics at 106.25MHz www.pletronics.com 425-776-1880 3 SM77D Series 3.3 V CMOS Clock Oscillators April 2014 Electrical Specification for 3.30V + _10% over the specified temperature range Item Min Typ Max Unit VOUT High (VOH) 2.5 2.7 - V VCC = 2.97V, IOH = +8 mA VOUT Low (VOL) - 0.3 0.4 V VCC = 2.97V, IOL = -8 mA Output TRISE and TFALL - 0.8 1.5 nS >130 MHz - 1.0 2.0 nS >110 MHz and < 130 MHz - 1.2 2.5 nS >80 MHz and < 110 MHz - 2.0 3.0 nS < 80 MHz - 1.2 2.0 nS >130 MHz - 1.3 2.5 nS >110 MHz and < 130 MHz - 1.4 3.0 nS >80 MHz and < 110 MHz - 2.0 4.0 nS < 80 MHz - 2.1 3.5 nS >110 MHz and < 130 MHz - 2.1 4.5 nS >80 MHz and < 110 MHz - 3.0 5.0 nS < 80 MHz - 30 70 mA >130 MHz - 25 60 mA >110 MHz and < 130 MHz - 20 50 mA >80 MHz and < 110 MHz - 18 40 mA < 80 MHz - 40 90 mA >130 MHz - 32 70 mA >110 MHz and < 130 MHz - 26 57 mA >80 MHz and < 110 MHz - 22 45 mA < 80 MHz - 44 80 mA >110 MHz and < 130 MHz - 34 65 mA >80 MHz and < 110 MHz - 29 50 mA < 80 MHz VCC Supply Current (ICC) Condition CLOAD = 15 pF 10% to 90% of VCC See Load Circuit CLOAD =30 pF 10% to 90% of VCC See Load Circuit CLOAD = 50 pF 10% to 90% of VCC See Load Circuit CLOAD = 15 pF CLOAD = 30 pF CLOAD = 50 pF Specifications with Pad 1 E/D open circuit www.pletronics.com 425-776-1880 4 SM77D Series 3.3 V CMOS Clock Oscillators April 2014 Load Circuit and Test Waveform Reliability: Environmental Com pliance Parameter Condition Mechanical Shock MIL-STD-883 Method 2002, Condition B Vibration MIL-STD-883 Method 2007, Condition A Solderability MIL-STD-883 Method 2003 Thermal Shock MIL-STD-883 Method 1011, Condition A ESD Rating Model Minimum Voltage Conditions Human Body Model 1500 MIL-STD-883 Method 3115 Charged Device Model 1000 JESD 22-C101 Package Labeling Label is 1" x 2.6" (25.4mm x 66.7mm) Font is Courier New Bar code is 39-Full ASCII www.pletronics.com Label is 1" x 2.6" (25.4mm x 66.7mm) Font is Arial 425-776-1880 5 SM77D Series 3.3 V CMOS Clock Oscillators April 2014 Mechanical: Inches A 0.276 _ +0.006 7.00 _ +0.15 B 0.197 _ +0.006 5.00 _ +0.15 C 0.068 _ +0.018 1.73 _ +0.44 D1 0.038 0.96 E1 0.200 5.08 1 0.004 0.10 G1 0.050 1.27 H1 0.055 1.40 I1 0.024 0.60 J1 0.004 0.10R K1 0.008 0.020R F The detents marked “L” on the package ends are optional Not to Scale 1 Typical dimensions mm Contacts (pads) : Gold 11.8 to 39.4 µinches (0.3 to 1.0 µm) over Nickel 50 to 350 µinches (1.27 to 8.89 µm) Pad Function Note 1 Output Enable/Disable When this pad is not connected the oscillator shall operate. When this pad is logic low the output will be inhibited (high impedance state.) Recommend connecting this pad to VCC if the oscillator is to be always on. 2 Ground (GND) 3 Output 4 Supply Voltage (VCC) Recommend connecting appropriate power supply bypass capacitors as close as possible. Layout and application information For • • • • Optim um Jitter Perform ance, Pletronics recom m ends: a ground plane under the device no large transient signals (both current and voltage) should be routed under the device do not layout near a large m agnetic field such as a high frequency switching power supply do not place near piezoelectric buzzers or m echanical fans. www.pletronics.com 425-776-1880 6 SM77D Series 3.3 V CMOS Clock Oscillators April 2014 Reflow Cycle (typical for lead free processing) The part m ay be reflowed 3 tim es without degradation. Tape and Reel: available for quantities of 250 to 1000 per reel (< 250 = cut tape) Constant Dimensions Table 1 Tape Size D0 8mm D1 Min E1 P0 1.0 12mm 1.5 16mm +0.1 -0.0 24mm P2 S1 Min T Max 0.6 0.6 T1 Max 2.0 +0.05 _ 1.5 1.75 4.0 1.5 _ +0.1 _0.1 + 0.1 2.0 _ +0.1 1.5 Variable Dimensions Table 2 Tape Size B1 Max E2 Min F P1 T2 Max W Max Ao, Bo & Ko 16 mm 12.1 14.25 7.5 _ +0.1 8.0 _ +0.1 8.0 16.3 Note 1 Note 1: Embossed cavity to conform to EIA-481-B Dimensions in mm Not to scale REEL DIMENSIONS A B inches 7.0 10.0 13.0 mm 177.8 254.0 330.2 inches 2.50 4.00 3.75 mm 63.5 101.6 95.3 Tape Width 16.4 +2.0 -0.0 16.0 C mm D mm 13.0 +0.5 / -0.2 16.4 +2.0 -0.0 16.4 +2.0 -0.0 Reel dimensions may vary from the above www.pletronics.com 425-776-1880 7 SM77D Series 3.3 V CMOS Clock Oscillators April 2014 IM PORTANT NOTICE Pletronics Incorporated (PLE) reserves the right to m ake corrections, im provem ents, m odifications and other changes to this product at anytim e. PLE reserves the right to discontinue any product or service without notice. Custom ers are responsible for obtaining the latest relevant inform ation before placing orders and should verify that such inform ation is current and com plete. All products are sold subject to PLE’s term s and conditions of sale supplied at the tim e of order acknowledgm ent. PLE warrants perform ance of this product to the specifications applicable at the tim e of sale in accordance with PLE’s lim ited warranty. Testing and other quality control techniques are used to the extent PLE deem s necessary to support this warranty. Except where m andated by specific contractual docum ents, testing of all param eters of each product is not necessarily perform ed. PLE assum es no liability for application assistance or custom er product design. Custom ers are responsible for their products and applications using PLE com ponents. To m inim ize the risks associated with the custom er products and applications, custom ers should provide adequate design and operating safeguards. PLE products are not designed, intended, authorized or warranted to be suitable for use in life support applications, devices or system s or other critical applications that m ay involve potential risks of death, personal injury or severe property or environm ental dam age. Inclusion of PLE products in such applications is understood to be fully at the risk of the custom er. Use of PLE products in such applications requires the written approval of an appropriate PLE officer. Questions concerning potential risk applications should be directed to PLE. PLE does not warrant or represent that any license, either express or im plied, is granted under any PLE patent right, copyright, artwork or other intellectual property right relating to any com bination, m achine or process which PLE product or services are used. Inform ation published by PLE regarding third-party products or services does not constitute a license from PLE to use such products or services or a warranty or endorsem ent thereof. Use of such inform ation m ay require a license from a third party under the patents or other intellectual property of the third party, or a license from PLE under the patents or other intellectual property of PLE. Reproduction of inform ation in PLE data sheets or web site is perm issible only if the reproduction is without alteration and is accom panied by associated warranties, conditions, lim itations and notices. Reproduction of this inform ation with alteration is an unfair and deceptive business practice. PLE is not responsible or liable for such altered docum ents. Resale of PLE products or services with statem ents different from or beyond the param eters stated by PLE for that product or service voids all express and im plied warranties for the associated PLE product or service and is an unfair or deceptive business practice. PLE is not responsible for any such statem ents. Contacting Pletronics Inc. Pletronics Inc. Tel: 425-776-1880 19013 36 th Ave. W est Fax: 425-776-2760 Lynnwood, W A 98036-5761 USA E-m ail: ple-sales@ pletronics.com URL: www.pletronics.com Copyright © 2006, 2007, 2010, Pletronics Inc. www.pletronics.com 425-776-1880 8