NJM41010 2-Input 1-Output Video Driver Q GENERAL DESCRIPTION The NJM41010 is a 2-Input 1-Output general-purpose video switch. It includes 6dB amplifier and 75ohm driver circuit. The NJM41010 is suitable for a variety of AV equipment because of a small package and wide operating temperature range. Q PACKAGE OUTLINE NJM41010F1 Q FEATURES O Operating Voltage 4.5 to 9.5V O Operating temperature range -40 to +85 °C* O 2-Input 1-Output Video Switch O 6dB Amplifier, 75Ω Driver Circuit O Frequency Characteristics 0dB at 10MHz O Sync-tip Clamp O Bipolar Technology O Small Package SOT-23-6 (MTP6) * NJM41010F1T : Wide operating temperature range type (-40 to +105°C) Q PIN CONFIGURATION 1.OUT 2.GND 1 6 2 5 3 4 3.VCC 4.VIN1 5.VIN2 6.VSW Q BLOCK DIAGRAM VCC GND IN1 CLAMP 6dB 75Ω Driver OUT IN2 CLAMP VSW Ver.8.1 -1- NJM41010 Q ABSOLUTE MAXIMUM RATINGS (Ta=25°C) PARAMETERS Supply Voltage Power Dissipation SYMBOL RATINGS UNIT Vcc PD Topr Tstg 11.0 510 (Note1) -40 to +85(Note2) -40 to +150 V mW Operating Temperature Range °C Storage Temperature Range °C (Note 1) At on a board of EIA/JEDEC specification. (114.3 x 76.2 x 1.6mm 2 layers, FR-4) (Note 2) It has high operating temperature range product.(-40 to +105°C) Q RECOMMENDED OPEARATING CONDITION (Ta= 25 °C) PARAMETER Operating Voltage SYMBOL TEST CONDITION Vopr MIN. TYP. MAX. UNIT +4.5 +5.0 +9.5 V MIN. TYP. MAX. UNIT - 8.0 15 mA QELECTRICAL CHARACTERISTICS (Vcc= 5.0V, RL= 150Ω, Ta= 25°C) PARAMETER SYMBOL TEST CONDITION Operating Current ICC No signal Voltage Gain Gv Vin=1MHz, 1.0Vp-p Sine-wave 5.5 6.0 6.5 dB Maximum Output Voltage Swing Vom Vin=100kHz, Sine-wave, THD=1% 2.2 - - Vp-p Frequency Characteristics Gf Vin=10MHz/1MHz, 1.0Vpp Sine-wave -1.0 0 1.0 dB Channel Cross talk CT Vin=4.43MHz, 1.0Vp-p, Sine-wave - -60 -50 dB Differential Gain DG Vin=1.0Vpp 10step Video signal - 0.5 - % Differential Phase DP Vin=1.0Vpp 10step Video signal - 0.2 - deg ISWH V=5V - - 300 µA ISWL V=0.3V - - 30 µA VthH VSW 2.0 - V+ V VthL VSW 0 - 1.0 V Switch inflow current High Level Switch inflow current Low Level Switch Change Voltage High Level Switch Change Voltage Low Level Q SWITCH FUNCTION PIN VSW (Output signal select) -2- MODE NOTES H IN2 output L IN1 output OPEN IN1 output NJM41010 Q TERMINAL FUNCTION PIN No. PIN NAME FUNCTION EQUIVALENT CIRCUIT DC VOLTAGE VCC 8.01kΩ 1 OUT OUTPUT 1.3V GND 2 GND GND - - 3 VCC VCC - - VCC 270Ω 4 IN1 270Ω INPUT 1 1.56V GND VCC 270Ω 5 IN2 270Ω INPUT 2 1.56V GND 16kΩ 6 VSW SWITCH VOLTAGE INPUT 8kΩ GND -3- NJM41010 Q TEST CIRCUIT 75Ω + 1 OUT VSW 6 2 GND IN2 5 1000µF 75Ω 0.1µF 3 VCC 0.1µF + 75Ω IN1 4 0.1µF 47µF 75Ω Q APPLICATION CIRCUIT1 75Ω + 1 OUT VSW 6 2 GND IN2 5 470µF 0.1µF 3 VCC 0.1µF + 75Ω IN1 4 0.1µF 47µF 75Ω Q APPLICATION CIRCUIT2 (Two-line driving circuit) 75Ω 470µF 75Ω + 1 OUT VSW 6 2 GND IN2 5 0.1µF 3 VCC 0.1µF + 47µF 75Ω IN1 4 0.1µF 75Ω Note This circuit drives two-line of 150Ω. However, it may cause to lose synchronization by an input signal of large APL change (100% white signals more than 1Vp-p). Confirm the large APL change waveform (100% white signals more than 1Vp-p) and evaluate sufficiently. -4- NJM41010 ♦Clamp circuit 1. Operation of Sync-tip-clamp Input circuit will be explained. Sync-tip clamp circuit (below the clamp circuit) operates to keep a sync tip of the minimum potential of the video signal. Clamp circuit is a circuit of the capacitor charging and discharging of the external input Cin. It is charged to the capacitor to the external input Cin at sync tip of the video signal. Therefore, the potential of the sync tip is fixed. And it is discharged charge by capacitor Cin at period other than the video signal sync tip. This is due to a small discharge current to the IC. In this way, this clamp circuit is fixed sync tip of video signal to a constant potential from charging of Cin and discharging of Cin at every one horizontal period of the video signal. The minute current be discharged an electrical charge from the input capacitor at the period other than the sync tip of video signals. Decrease of voltage on discharge is dependent on the size of the input capacitor Cin. If you decrease the value of the input capacitor, will cause distortion, called the H sag. Therefore, the input capacitor recommend on more than 0.1uF. signal input Cin charge current Vin Clamp circuit diccharge current < Clamp circuit > A. Cin is large B. Cin is small (H sag experience) clamp potential clamp potential charge period discharge period charge period charge period discharge period charge period < Waveform of input terminal > 2. Input impedance The input impedance of the clamp circuit is different at the capacitor discharge period and the charge period. The input impedance of the charging period is a few kΩ. On the other hand, the input impedance of the discharge period is several MΩ. Because is a small discharge-current through to the IC. Thus the input impedance will vary depending on the operating state of the clamp circuit. 3. Impedance of signal source Source impedance to the input terminal, please lower than 200Ω. A high source impedance, the signal may be distorted. If so, please to connect a buffer for impedance conversion. -5- NJM41010 Q TYPICAL CHARACTERISTICS Operating Current vs. Supply Voltage Voltage Gain vs. Supply Voltage 1.0Vpp, 1MHz Sine Signal Input 6.50 10.0 8.0 6.25 Voltage Gain [dB] Operating Current [mA] IN1 IN2 6.0 4.0 6.00 5.75 2.0 0.0 5.50 4 6 8 10 4 12 5 6 Supply Voltage [V] 8 9 10 12 Frequency Characteristic vs. Supply Voltage Total Harmonic Distortion=1%, 100kHz 1.0Vpp, 10MHz/1MHz 10.0 1.00 Frequency Characteristic [dB] IN1 IN2 8.0 6.0 4.0 2.0 IN1 IN2 0.50 0.00 -0.50 -1.00 4 5 6 7 8 9 10 11 12 4 5 6 7 8 9 10 11 Supply Voltage [V] Supply Voltage [V] Cross Talk vs. Supply Voltage Differential Gain vs. Supply Voltage 1.0Vpp 4.43MHz, Sine Signal Input 12 1.0Vpp, 10step Video Signal Input -50 2.0 IN1 IN2 IN1 IN2 Differential Gain [%] -55 Cross Talk [dB] 11 Supply Voltage [V] Maximam Output Voltage Swing vs. Supply Voltage Maximam Output Voltage Swing [V] 7 -60 -65 -70 1.5 1.0 0.5 0.0 4 5 6 7 8 9 10 Supply Voltage [V] 11 12 4 5 6 7 8 9 Supply Voltage [V] 10 11 12 Ver.8.1 -6- NJM41010 Differential Phase vs. Supply Voltage Signal to Noise Ratio vs. Suppply Voltage 1.0Vpp, 10step Video Signal Input 1.0Vpp, 100% White Video Signal Input 2.0 100.0 IN1 IN2 Signal to Noise Ratio [dB] Differential Phase [deg] IN1 IN2 1.5 1.0 0.5 0.0 80.0 70.0 60.0 4 5 6 7 8 9 10 11 12 4 5 6 8 9 10 11 12 Supply Voltage [V] Switching Voltage Level vs. Supply Voltage Switch Terminal Current vs. Supply Voltage 300 Switch Terminal Current [uA] High Level Low Level 4.0 3.0 2.0 1.0 0.0 High Level Low Level 250 200 150 100 50 0 4 5 6 7 8 9 10 11 12 4 5 6 Supply Voltage [V] 7 8 9 10 11 12 Supply Voltage [V] Offset Voltage vs. Supply Voltage Terminal Voltage vs. Supply Voltage 5.0 0.10 IN1 IN2 OUT 0.08 Offset Voltage [V] 4.0 Terminal Voltage [V] 7 Supply Voltage [V] 5.0 Switching Voltage Level [V] 90.0 3.0 2.0 1.0 0.06 0.04 0.02 0.0 0.00 4 5 6 7 8 9 Supply Voltage [V] 10 11 12 4 5 6 7 8 9 10 11 12 Supply Voltage [V] -7- NJM41010 Voltage Gain vs. Temperature Operating Current vs. Temperature 1.0Vpp, 1MHz Sine Signal Input 10.0 6.50 8.0 6.25 Voltage Gain [dB] Operating Current [mA] IN1 IN2 6.0 4.0 5.75 2.0 0.0 6.00 -50 0 50 100 5.50 150 -50 o 0 50 100 150 o Ambient Temperature [ C] Ambient Temperature [ C] Maximam Output Voltage Swing vs. Temperature Frequency Characteristic vs. Temperature Total Harmonic Distortion=1%, 100kHz 1.0Vpp, 10MHz/1MHz 1.00 IN1 IN2 3.5 3.0 2.5 2.0 -50 0 50 100 Frequency Characteristic [dB] Maximam Output Voltage Swing [V] 4.0 IN1 IN2 0.50 0.00 -0.50 -1.00 150 -50 o 50 100 150 o Ambient Temperature [ C] Ambient Temperature [ C] Differential Gain vs. Temperature Cross Talk vs. Temperature -50 0 1.0Vpp 10step Video Signal Input 1.0Vpp 4.43MHz, Sine Signal Input 2.0 IN1 IN2 Differential Gain [%] Cross Talk [dB] -55 -60 -65 -70 -50 0 50 100 o Ambient Temperature [ C] -8- IN1 IN2 150 1.5 1.0 0.5 0.0 -50 0 50 100 150 o Ambient Temperature [ C] NJM41010 Signal to Noise Ratio vs. Temperature Differential Phase vs. Temperature 1.0Vpp, 100% White Video Signal Input 1.0Vpp 10step Video Signal Input 100 Differential Phase [%] IN1 IN2 1.5 1.0 0.5 0.0 -50 0 50 100 Signal to Noise Ratio [dB] 2.0 IN1 IN2 90 80 70 60 150 -50 Switching Voltage Level vs. Temperature 150 4.00 3.00 2.00 1.00 Switch Terminal Curren [uA] 300 High Level Low Level Switching Voltage Level [V] 100 Switch Terminal Current vs. Temperature 5.00 0.00 High Level Low Level 250 200 150 100 50 0 -50 0 50 100 150 -50 o 0 50 100 150 o Ambient Temperature [ C] Ambient Temperature [ C] Terminal Voltage vs. Temperature Offset Voltage vs. Temperature 0.05 3.0 IN1 IN2 OUT 0.04 Offset Voltage [V] 2.5 Terminal Voltage [V] 50 Ambient Temperature [ C] Ambient Temperature [ C] 2.0 1.5 1.0 0.03 0.02 0.01 0.5 0.0 0 o o -50 0 50 100 o Ambient Temperature [ C] 150 0.00 -50 0 50 100 150 o Ambient Temperature [ C] -9- NJM41010 Voltage Gain vs. Freqency 1.0Vpp, Sine Signal Input 10 IN1 IN2 Voltage Gain [dB] 5 0 -5 -10 -15 -20 0.1 1 10 100 Frequency [MHz] [CAUTION] The specifications on this databook are only given for information , without any guarantee as regards either mistakes or omissions. The application circuits in this databook are described only to show representative usages of the product and not intended for the guarantee or permission of any right including the industrial rights. - 10 -