PME-xxxxTLF Mainzer Straße 151–153 D-55299 Nackenheim Tel. +49 6135 7026-0 Fax: +49 6135 931070 www.peak-electronics.de [email protected] PSD-SERIES Rev.04-2009 1 Watt Unregulated Single Output SMD Case – Full Pin 1 kV DC I/O Isolation Low Ripple and Noise The PSD series is a family of cost effective 1 W single output DC/DC converters. These converters are in an ultra miniature SMD full-pin case. Devices are encapsulated. High performance features: 1000VDC input/output isolation, industrial standard pinout, high power density, no heat sink required All specifications typical at Ta=25°C, nominal input voltage and full load unless otherwise specified Input Specifications Voltage Range Input Filter ± 10% Capacitors Output Specifications Voltage Accuracy Short Circuit Protection Line Regulation Ripple and Noise (20Mhz bandwidth) Temperature Coefficient ± 3% Short Term ± 1.5%, max. (For Vin Change of 1%) ± 1.2%, max. (For Vin Change of 1%) 20%, max. 15%, max. 10%, max. 75 mV pk-pk, max. ± 0.03% / °C General Specifications Efficiency I/O Isolation Voltage (3 sec.) I/O Isolation Resistance (Tested at 500 VDC) Switching Frequency Humidity Reliability Calculated MTBF (MIL-HDBK-217F) See Table 1000 VDC 1000 M Ohm 100 kHz, typ (5, 12 Vin); 500 kHz (24Vin) 95% rel H > 3500 khrs Physical Specifications Case Material Potting Material Weight Non Conductive Black Plastic (UL94V-0 rated) Epoxy (UL94V-0 rated) ~ 1.4g, max. Load Regulation (10% - 100%) 3.3 Vout Others 3.3 Vout 5 Vout 9, 12, 15, 24 Vout Environment Specifications Operating Temperature Storage Temperature Cooling Soldering RoHS Conform -40 to +85°C (ambient) -55 to +125°C Free Air Convection (10mm distance required) Not usable for heat steam soldering PSD-Series – PME-xxxxTLF – Single Output – SMD - Plastic Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 1/4 Selection Guide Single Output ) ) mA (mA ) DC) ax. in. ( V DC ( m m V t t ( e (%) rren rren ltag tage ncy t Vo t Cu t Cu Vol e u u u t i p p p c u t t t i Inp Ou Ou Ou Eff Order # SINGLE OUTPUT PME-3R33R3TLF PME-3R305TLF PME-053R3TLF PME-0505TLF PME-0509TLF PME-0512TLF PME-0515TLF PME-1205TLF PME-1209TLF PME-1212TLF PME-1215TLF PME-243R3TLF PME-2405TLF PME-2409TLF PME-2412TLF PME-2415TLF PME-2424TLF 3.3 3.3 5 5 5 5 5 12 12 12 12 24 24 24 24 24 24 3.3 5 3.3 5 9 12 15 5 9 12 15 3.3 5 9 12 15 24 303 200 303 200 111 84 67 200 111 84 67 300 200 110 83 67 42 30 20 30 20 12 9 7 20 12 9 7 30 20 11 8 7 4 73 74 72 77 76 79 78 69 73 73 74 69 70 72 75 76 77 If you need other specifications, please enquire. Notes: PSD-Series – PME-xxxxTLF – Single Output – SMD - Plastic Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 2/4 Package / Pinning / Derating PIN CONNECTIONS # SINGLE 1 - Vin 2 +Vin 4 - Vout 5 +Vout Others N.C. Reflow: P eak.Temp 2 60℃ 10 S ec Max 250 Temperat ure (℃ ) 220℃ 200 90 S ec Max (> 220℃) 150 100 50 0 Tim e (sec.) PSD-Series – PME-xxxxTLF – Single Output – SMD - Plastic Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 3/4 App Notes Requirement on output load To ensure this module can operate efficiently and reliably, during operation, the minimum output load is not less than 10% of the full load, and that this product should never be operated under no-load! If the actual output power is very small, please connect a resistor with proper resistance at the output end in parallel to increase the load. Recommended testing circuit If you want to further decrease the input/output ripple, an “LC” filtering network may be connected to the input and output ends if the DC/DC converter, see Figure on the right hand side. It should also be noted that the inductance and the frequency of the “LC” filtering network should be staggered with the DC/DC frequency to avoid mutual interference. However, the capacitance of the output filter capacitor must be proper. If the capacitance is too big, a start-up problem might arise. For every channel of output, provided the safe and reliable operation is ensured, the greatest capacitance of its filter capacitor sees (see Table). EXTERNAL CAPACITOR TABLE Output Voltage Regulation and Vin Vout Cin (uF) Cout (uF) Over-voltage (VDC) (VDC) Protection Circuit 3.3 / 5 4.7 3.3 / 5 10 The simplest device for output voltage 12 2.2 9 4.7 regulation, over-voltage and over24 0.47 12 2.2 current protection is a linear voltage --15 1 regulator with overheat protection that --24 0.47 is connected to the input or output It’s not recommend to connect any external end in series. capacitor in the application field with less than 0.5 watt output. Overload Protection Under normal operating conditions, the output circuit of these products has no protection against over-current and short-circuits. The simplest method is to connect a self-recovery fuse in series at the input end or add a circuit breaker to the circuit. No parallel connection or plug and play. PSD-Series – PME-xxxxTLF – Single Output – SMD - Plastic Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 4/4