PMA-xxxxTLF Mainzer Straße 151–153 D-55299 Nackenheim Tel. +49 6135 7026-0 Fax: +49 6135 931070 www.peak-electronics.de [email protected] PSD-SERIES Rev.04-2009 1 Watt Unregulated Dual Output – Full Pin SMD Case 1 kV DC I/O Isolation Low Ripple and Noise The PMA-xxxxZLF series is a family of cost effective 1 W dual output DC/DC converters. These converters are in an ultra miniature SMD 10-pin case. Devices are encapsulated. High performance features: 1000VDC input/output isolation, industrial standard pinout, high power density, no heatsink required All specifications typical at Ta=25°C, nominal input voltage and full load unless otherwise specified Input Specifications Voltage Range ± 10% Output Specifications Voltage Accuracy Short Circuit Protection Line Regulation Load Regulation (10% - 100%) ± 5%, typ. Short Term ± 1.2%, max. (For Vin Change of 1%) 5 Vout 15%, max. 9, 12, 15, 24 Vout 10%, max. Ripple and Noise (20Mhz bandwidth) 75 mV pk-pk, max. Temperature Coefficient ± 0.03% / °C General Specifications Efficiency I/O Isolation Voltage (3 sec.) I/O Isolation Resistance (Tested at 500 VDC) Switching Frequency Humidity Reliability Calculated MTBF (MIL-HDBK-217F) See Table 1000 VDC 1000 M Ohm 100 kHz, typ (5, 12 Vin); 500 kHz (24Vin) 95% rel H > 3500 khrs Physical Specifications Case Material Potting Material Weight Non Conductive Black Plastic (UL94V-0 rated) Epoxy (UL94V-0 rated) ~ 1.7g, typ. Environment Specifications Operating Temperature Storage Temperature Cooling Soldering RoHS Conform -40 to +85°C (ambient) -55 to +125°C Free Air Convection (10mm distance required) Not usable for heat steam soldering PSD-Series – PMA-xxxxTLF – Dual Output – SMD - Plastic Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 1/4 Selection Guide Dual Output lta t Vo Inpu Order # SINGLE OUTPUT PMA-0505TLF PMA-0509TLF PMA-0512TLF PMA-0515TLF PMA-1205TLF PMA-1209TLF PMA-1212TLF PMA-1215TLF PMA-2405TLF PMA-2409TLF PMA-2412TLF PMA-2415TLF PMA-2424TLF 5 5 5 5 12 12 12 12 24 24 24 24 24 VD ge ( C) put Out ta Vol ±5 ±9 ± 12 ± 15 ±5 ±9 ± 12 ± 15 ±5 ±9 ± 12 ± 15 ± 24 ) ) mA (m A ax. in. ( m m t t rren rren (%) nc y t Cu t Cu e u u i p p c t t i Ou Ou Eff ) VDC ge ( ± 100 ± 56 ± 42 ± 33 ± 100 ± 56 ± 42 ± 33 ± 100 ± 56 ± 42 ± 33 ± 21 ± 10 ±6 ±5 ±4 ± 10 ±6 ±5 ±4 ± 10 ±6 ±5 ±4 ±2 71 77 78 78 71 73 74 74 72 74 76 77 78 If you need other specifications, please enquire. Notes: PSD-Series – PMA-xxxxTLF – Dual Output – SMD - Plastic Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 2/4 Package / Pinning / Derating 10.16 (0.40) 10 9 8 7 0.60 (0.02) 6 6.50 (0.25) PEAK Modelcode Datecode 1 2 3 4 5 2.54 (0.10) 15.24 (0.60) All dimensions are typical in millimeters (inches). - Pin pitch tolerance: +/-0.35 (+/-0.014) - Case tolerance +/-0.5 (+/-0.02) PSD-Series Specification may change without notice. PIN CONNECTIONS # DUAL 1 - Vin 2 +Vin 4 Common 5 - Vout 7 +Vout 10 N.C. Others N.C. Reflow: P eak.Temp 2 60℃ 10 S ec Max 250 Temperat ure (℃ ) 220℃ 200 90 S ec Max (> 220℃) 150 100 50 0 Tim e (sec.) PSD-Series – PMA-xxxxTLF – Dual Output – SMD - Plastic Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 3/4 App Notes Requirement on output load To ensure this module can operate efficiently and reliably, during operation, the minimum output load is not less than 10% of the full load, and that this product should never be operated under no-load! If the actual output power is very small, please connect a resistor with proper resistance at the output end in parallel to increase the load. Recommended testing circuit If you want to further decrease the input/output ripple, an “LC” filtering network may be connected to the input and output ends if the DC/DC converter, see Figure on the right hand side. It should also be noted that the inductance and the frequency of the “LC” filtering network should be staggered with the DC/DC frequency to avoid mutual interference. However, the capacitance of the output filter capacitor must be proper. If the capacitance is too big, a start-up problem might arise. For every channel of output, provided the safe and reliable operation is ensured, the greatest capacitance of its filter capacitor sees (see Table). EXTERNAL CAPACITOR TABLE Vin Vout Cin (uF) Cout (uF) (VDC) (VDC) 5 4.7 ±5 4.7 12 2.2 ±9 2.2 24 1 ± 12 1 --± 15 1 It’s not recommended to connect any external capacitor in the application field with less than 0.5 watt output. Output Voltage Regulation and Over-voltage Protection Circuit The simplest device for output voltage regulation, over-voltage and over-current protection is a linear voltage regulator with overheat protection that is connected to the input or output end in series. Overload Protection Under normal operating conditions, the output circuit of these products has no protection against over-current and short-circuits. The simplest method is to connect a self-recovery fuse in series at the input end or add a circuit breaker to the circuit. No parallel connection or plug and play. PSD-Series – PMA-xxxxTLF – Dual Output – SMD - Plastic Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 4/4