DOS(H)30 SERIES POINT OF LOAD DC-DC CONVERTER FEATURES APPLICATIONS Wireless Network Telecom/Datacom Industry Control System Distributed Power Architectures Semiconductor Equipment Microprocessor Power Applications T E C H N I C A L S P E C I F I C AT I O N • OUTPUT CURRENT UP TO 30A • SMALL SIZE AND LOW PROFILE : DOS30-05T:1.30 X 0.53 X 0.37 INCH , DOH30-05T:2.00 X 0.50 X 0.37 INCH DOS30-12T:1.30 X 0.53 X 0.31 INCH , DOH30-12T:2.00 X 0.50 X 0.31 INCH • HIGH EFFICIENCY UP TO 93%@5VIN, 3.3VOUT, FULL LOAD • DOS(H)30-05T : 4.5VDC TO 5.5VDC INPUT, 0.8VDC TO 3.63VDC OUTPUT DOS30-12T : 6.0VDC TO 14.0VDC INPUT, 0.8VDC TO 3.63VDC OUTPUT DOH30-12T : 6.0VDC TO 14.0VDC INPUT, 0.8VDC TO 5.5VDC OUTPUT OUTPUT VOLTAGE PROGRAMMABLE VIA EXTERNAL RESISTOR • SMD PACKAGE QUALIFIED FOR LEADFREE REFLOW SOLDER PROCESS ACCORDING IPC J-STD-020D • FIXED SWITCHING FREQUENCY (300kHZ) • MONOTONIC START-UP INTO PRE-BIASED OUTPUT • OUTPUT VOLTAGE SEQUENCING • PARALLEL OPERATION WITH ACTIVE CURRENT SHARING • SAFETY MEETS UL60950-1, EN60950-1, & IEC60950-1 • CE MARK MEETS 2006/95/EC, 2011/95/EC and 2004/108/EC • COMPLIANT TO RoHS II & REACH OPTIONS POSITIVE LOGIC REMOTE ON/OFF, CURRENT SHARE, EXTRA GND PIN, LONG PINS DESCRIPTION □□ All specifications are typical at nominal input, 3.3Vo, full load and 25ºC otherwise OUTPUT SPECIFICATIONS DOS30-05T 30A max. DOH30-05T 30A max. DOS30-12T 0.8≦Vout≦2.75VDC 30A max. Output current 2.75<Vout≦3.63VDC 20A max. DOH30-12T 0.8≦Vout≦2.75VDC 30A max. 2.75<Vout≦5.5VDC 25A max. Voltage accuracy ± 1.5%Vout(set) Minimum load 0% Vin=Vin(min.) to Vin(max.) Line regulation ± 0.1%Vout(set) at Full Load Load regulation No Load to Full Load ± 0.4%Vout(set) Ripple and noise (Note 2) 20MHz bandwidth 75mVp-p Temperature coefficient ±0.5% ΔIout/t = 5A/µs ,Vin(nom) Peak deviation 350mV Dynamic load Setting time Load change step response (50% to 100% or (Vout<10%peak 25µs (Note 2) 100% to 50% of Iout(max.)) deviation) ΔIout/t = 5A/µs ,Vin(nom) Peak deviation 250mV Dynamic load Load change step Setting time response (50% to 100% or (Vout<10%peak 40µs (Note 3) 100% to 50% of Iout(max.)) deviation) Output current limit 150% Output short-circuit current Hiccup, Automatics recovery ESR≧1mΩ 2000µF,max. External load capacitance ESR≧10mΩ 10000µF,max. Vin=Vin(min.) to Output voltage overshoot-startup 3%Vout(set), max. Vin(max.) and F.L. DOS30-05T 0.8VDC ~ 3.63VDC Voltage adjustability (see fig.1) DOH30-05T 0.8VDC ~ 3.63VDC (Note 4) 0.8VDC ~ 3.63VDC DOS30-12T 0.8VDC ~ 5.5VDC DOH30-12T GENERAL SPECIFICATIONS □□ DOS30T (SMD type), DOH30 T (SIP type) are non-isolated DC/DC converters that can deliver up to 30A of output current with full load efficiency of 93% at 5.0V input and 3.3V output. INPUT SPECIFICATIONS DOS30-05T DOH30-05T Vin(nom) =5VDC DOS30-12T DOH30-12T Vin(nom) =12VDC Input voltage range 4.5 ~ 5.5VDC Vin,min.=Vout(set)+1.5VDC 6.0 ~ 14.0VDC Vin,min.=Vout(set)+2.4VDC Input filter (Note 5) Input under-voltage lockout Input reflected ripple current C filter Start-up voltage Shutdown voltage 4.4VDC 4.3VDC 5~20MHz, 1uH source impedance 100mAp-p ENVIRONMENTAL SPECIFICATIONS Operating ambient temperature Storage temperature range -40ºC ~ +85ºC(with derating) -55ºC ~ +125ºC Thermal shock MIL-STD-810F Vibration MIL-STD-810F Relative humidity(non-condensing) 5% to 95% RH Lead-free reflow solder process Moisture sensitivity level(MSL) Over temperature protection IPC J-STD-020D IPC J-STD-033B Level 2a 125ºC FEATURE SPECIFICATIONS Sequencing delay time (Note 6) 10ms, min. Tracking accuracy ∣VSEQ -Vout∣ Power-up (2V/ms) 100mV Vin(min) to Vin(max), Iout(min.) Power-down (1V/ms) to Iout(max.), VSEQ < Vout. 200mV Active load share (option) Accuracy 10% Iout (Note 7) Number of units in parallel 5pcs,max. Remote ON/OFF (Note 8) Negative logic(standard)ON = Open or -0.3V < Vr < 1.2V IIN=200µA,max. OFF = 3.0V < Vr < Vin(max.) IIN=3.3mA,max. Positive logic(option) ON = Open or 3.0V < Vr < Vin(max.) IIN=200µA,max. OFF= -0.3V < Vr < 1.2V IIN=3.3mA,max. Remote sense range 0.5V, max. Efficiency See table Isolation voltage None Switching frequency 300kHz±13% Safety meets IEC60950-1, UL60950-1, & EN60950-1 DOS30-05T 1.30X0.53X0.37 Inch (33.0X13.5X9.4 mm) 1.30X0.53X0.31 Inch (33.0X13.5X7.8 mm) DOS30-12T Dimensions Rise time Time for Vout to rise from 10% to 90%of Vout(set) 10ms, max. DOH30-05T 2.00X0.50X0.37 Inch (50.8X12.7X9.4 mm) Case 1 (Note 9) 2.5ms 2.00X0.50X0.31 Inch (50.8X12.7X7.8 mm) Turn-on delay time DOH30-12T Case 2 (Note 10) 2.5ms 6.0g(0.21oz) SMD Weight 7.0g(0.25oz) SIP MIL-HDBK-217F 1.258 x 106 hrs MTBF (Note 1) Page 1 of 3 www.pduke.com 2014/6/20 DOS(H)30 SERIES POINT OF LOAD DC-DC CONVERTER Efficiency No Load Current Vin(nom),3.3VDC, Min. Load Max. Load Vin(nom),3.3VDC Full Load Output Current Model Name Package DOS30-05T SMD DOH30-05T SIP DOS30-12T SMD DOH30-12T SIP Input Voltage Output Voltage 4.5 ~ 5.5VDC Vin,min.=Vout(set)+1.5V 0.8 ~ 3.63VDC 0A 30A 180mA 93% 0.8 ~ 3.63VDC 0A 30A 180mA 93% 200mA 92% 200mA 92% 0.8 ≦Vout≦ 2.75VDC 6.0 ~ 14.0VDC 2.75 <Vout≦ 3.63VDC Vin,min.=Vout(set)+2.4V 0.8 ≦Vout≦ 2.75VDC 2.75 <Vout≦ 5.5VDC 30A 20A 30A 25A 0A 0A Note 1. MIL-HDBK-217F @Tc=70 ºC, Full load. 2. External with Cout = 1µF ceramic//10µF tantalum capacitors. 3. External with Cout = 2×150µF polymer capacitors. 4. Output voltage programmable from 0.8V to 5.0V by connecting a single resistor (shown as Rtrim in Table 1) between the TRIM and GND pins of the module. To calculate the value of the resistor Rtrim for a particular output voltage Vout, use the following equation: 5. 1200 - 100 Ω Rtrim = Vout - 0.80 To make sure the module is stable, input external capacitors is necessary that minimize input ripple voltage of the module. Delay from Vin,min. to application of voltage on SEQ pin. Selecting current share function that the regulations may not meet listed specification. The On/Off signal is referenced to ground. The standard remote On/Off logic of the device is negative logic. Adding a device code suffix “-P” is option for positive logic of remote On/Off. 9. Case 1 :On/Off input is set to logic low (module on) and then input power is applied (delay from instant at which Vin=Vin(min.) until Vout=10% of Vout(set)) 10. Case 2 :Input power is applied for at least one second and then the On/Off input is set to logic low (delay form instant at which Von/off=0.3V until Vout=10% of Vout(set)) 6. 7. 8. CAUTION: This power module is not internally fused. An input line fuse must always be used. Figure 1 DOS30-05T, Vout=3.3V Page 2 of 3 Table 1. Derating Curve www.pduke.com Trim Table Vout(set) (V) Rtrim (Ω) 0.8 Open 1.2 2900 1.5 1614 1.8 1100 2.5 605 3.3 380 5.0 185 Table 2. Device Options Option Suffix Remote On/Off -P Positive Logic Current Share -S Extra GND pin 2 extra GND pins -E only for SMD TYPE Long Pins -L 5.08mm±0.25mm only for SIP TYPE 2014/6/20 DOS(H)30 SERIES MECHANICAL DRAWING POINT OF LOAD ： DC-DC CONVERTER SIP TYPE PIN CONNECTION PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 DEFINE +OUTPUT +OUTPUT +SENSE +OUTPUT GND GND SHARE(option) GND + INPUT + INPUT SEQ TRIM CTRL SMD TYPE PIN CONNECTION PIN 1 2 3 4 5 6 7 8 9 10 DEFINE CTRL GND(option) SHARE(option) +SENSE TRIM +OUTPUT GND SEQ GND(option) + INPUT 1. All dimensions in Inch (mm) Tolerance: X.XX±0.02 (X.X±0.5) X.XXX±0.01 (X.XX±0.25) 2. Pin pitch tolerance ±0.01 (0.25) 3. Pin dimension tolerance ±0.004 (0.1) Page 3 of 3 www.pduke.com 2014/6/20