60 MHz SAW Filter 0.63 MHz bandwidth Part Number

60 MHz SAW Filter
0.63 MHz bandwidth
Part Number SF0060CN02289T
DESCRIPTION
•
•
•
60 MHz SAW bandpass filter with 0.63 MHz bandwidth.
35.1 x 20.6 mm DIP package.
RoHS compliant.
TYPICAL PERFORMANCE
Horizontal:
Vertical from Top:
S11
Frequency :
Relative Magnitude :
Relative magnitude :
Phase Linearity :
Group Delay Deviation :
1
10
1
2
50
MHz/div
dB/div
dB/div
deg/div
ns/div
S22
Spectrum Microwave
400 Nickerson Road, Marlborough, MA 01752, USA • Phone 1-508-251-6400 • Fax 1-508-251-6401
www.SpectrumMicrowave.com
DSSF0060CN02289T Rev A 9-Feb-2010
ECN 36650 Page 1 of 3
60 MHz SAW Filter
0.63 MHz bandwidth
Part Number SF0060CN02289T
SPECIFICATION
Parameter 1
Center Frequency (Fc) 1
1 dB Bandwidth 2
3 dB Bandwidth 2
55 dB Bandwidth 2
Device Delay
Average Insertion Loss (59.685-60.315 MHz)
Passband Amplitude Ripple 3
Passband Phase Ripple 3
Triple Travel and Spurious
Input VSWR at Fc (23˚C)
Output VSWR at Fc (23˚C)
Source and Load Impedance
Ambient Temperature
Notes:
Min
59.98
0.63
55
-
Typ
60.00
0.70
0.91
1.99
2.85
26.7
0.13
0.4
60
1.3
1.3
50
25
Max
60.02
0.96
2.10
3.00
34.0
0.50
4.0
1.5
1.5
-
Units
MHz
MHz
MHz
MHz
us
dB
dB p-p
deg p-p
dB
:1
:1
Ω
°C
1. Average of lower & upper 3 dB frequencies.
2. Referenced to the insertion loss of the device.
3. Defined as the difference between the highest and lowest levels in the minimum 1 dB bandwidth.
MAXIMUM RATINGS
Parameter
Storage Temperature Range
Operating Temperature Range
Input Power Level
Min
Max
-40
-25
-
85
85
13
Units
˚C
˚C
dBm
MATCHING CIRCUIT
Ls2
Ls1
3
Input
50 Ω
Single ended
Cp1
Rp1
Rp2
22
Typical component values:
(Minimum inductor Q = 40)
15
Ls1 = 240 nH
Cp1 = 33 pF
Rp1 = 200 Ω
Cp2
Output
50 Ω
Single ended
10
Ls2 = 240 nH
Cp2 = 33 pF
Rp2 = 200 Ω
Notes
• Suggest the use of 2% tolerance matching components.
• Tuning values shown are for reference only. Optimum values may change depending upon board layout.
Spectrum Microwave
400 Nickerson Road, Marlborough, MA 01752, USA • Phone 1-508-251-6400 • Fax 1-508-251-6401
www.SpectrumMicrowave.com
DSSF0060CN02289T Rev A 9-Feb-2010
ECN 36650 Page 2 of 3
60 MHz SAW Filter
0.63 MHz bandwidth
Part Number SF0060CN02289T
PACKAGE OUTLINE
Units: mm
Tolerances are ±0.15 mm except
for the overall length and width,
which are nominal values.
Pin Configuration:
Input:
3
Input Ground: 22
Output:
15
Output Ground: 10
Case Ground: All other pins
ISO 9001
Registered
All specifications are believed to be accurate and reliable. However, Spectrum Microwave reserves the right to make changes without notice.
© 2010 All rights reserved.
Spectrum Microwave
400 Nickerson Road, Marlborough, MA 01752, USA • Phone 1-508-251-6400 • Fax 1-508-251-6401
www.SpectrumMicrowave.com
DSSF0060CN02289T Rev A 9-Feb-2010
ECN 36650 Page 3 of 3