Classification
Issue No.
20091134
REFERENCE SPECIFICATION
Part Name
LIGHT TOUCH SWITCH
Part No.
EVQP0N02B
1/9
1. Notification Items
1.1 Law and the regulation which are applied
①This product has not been manufactured with ozone depleting chemical controlled under
the Montreal Protocol.
②This product complies with the RoHS Directive (Restriction of the use of certain
Hazardous Substance) in electical and electronic equipment (DIRECTIVE 2002/95/EC).
③All the materials used in this part are registered material under the Law Concerning
the Examination and Regulation of Manufacture etc. or Chemical Substances.
④Permission must be obtained from the Japanese government if the product that is subject
to the "Foreign Exchange and Foreign Trade Law" is to be exported or taken out of Japan.
1.2 Application Limits
This product was designed and manufactured for general electronics devices household
appliances, office equipment, data and communication equipment.
For the following applications in which high reliability and safety are required, or for
the applications in which the failure or malfunction of the products may directly
jeopardize life or cause threat of personal asset, please contact us beforehand.
･Aircraft and aerospace equipment, anti-disaster or anti-crime equipment, medical
equipment, transport equipment(automotives, trains, boat etc), high public
information processing devices or the other equipments or devices that are
equivalent to the above mentioned.
1.3 Handling of reference specification.
・Since the contents of this reference specification are subjected to change without
prior notifications,please request us a formal specification again for your
investigations before using.
1.4 Manufacturing Sites
① The country of manufacture : Malaysia
Panasonic Electronic Devices Malaysia Sdn. Bhd.
2. Summary
2.1 This specifications applies to the following types of switch.
Push-ON type S.P.S.T
2.2 This specifications is a constituent document of contract for business concluded between
your company and Panasonic Corporation.
2.3 Items not particularly specified in this specifications shall be in conformance with
JIS Standards.
Panasonic Electronic Devices Malaysia Sdn. Bhd.
REFERENCE ONLY
Classification
Issue No.
20091134
REFERENCE SPECIFICATION
Part Name
LIGHT TOUCH SWITCH
Part No.
EVQP0N02B
3. Dimension・Marking・Circuit diagram
Date code are indicated in the product.
Panasonic Electronic Devices Malaysia Sdn. Bhd.
2/9
Classification
Issue No.
20091134
REFERENCE SPECIFICATION
Part Name
LIGHT TOUCH SWITCH
Part No.
3/9
EVQP0N02B
4. General specification
4.1 Switch rating
DC 15 V 20 mA(max.) DC 2V 10μA(min.)
4.2 Operation temperature range -40
℃ ～ +85 ℃
4.3 Preservative temperature range Single condition：-40～+85 ℃
Taping condition：-20～+60 ℃
4.4 Standard conditions
Unless otherwise specified, the test and measurements shall be carried out as follows.
Ambient temperature :5～35 ℃
Relative humidity :45～85 %
Air pressure
:86～106 kPa
However, if doubt arises on the decision based on the measured values
under the above-mentioned conditions, the following conditions shall be
employed.
Ambient temperature :20± 2℃
Relative humidity :65±5 %
Air pressure
:86～106 kPa
5. Performance
5.1 Electrical characteristics
No.
ITEM
TEST CONDITION
PERFORMANCE
5.1.1 Contact
resistance
Push force
: {Operation force} × 2
Measurement tool : Contact resistance meter
(Capable of 10 μA ～ 10 mA)
100 mΩ max.
5.1.2 Insulation
resistance
DC 100 V (Between terminals)
100 MΩ min.
5.1.3 Withstand
voltage
AC 250 V for 1 minute. (Between terminals)
No insulation
destruction
5.1.4 Bouncing
Operation speed : 3～4 times/s
ON
10 ms max.
OFF
10 ms max.
Panasonic Electronic Devices Malaysia Sdn. Bhd.
Classification
Issue No.
20091134
REFERENCE SPECIFICATION
Part Name
LIGHT TOUCH SWITCH
Part No.
4/9
EVQP0N02B
5.2 Mechanical characteristics
No.
ITEM
TEST CONDITION
5.2.1 Operation
force
PERFORMANCE
Push force
0.6 +-
0.20
0.20
N
Return force
0.1 N min.
5.2.2 Travel to
closure
0.30
5.2.3 Push
strength
5.2.4 Vibration
test
50 N
for 60 sec.
1) Amplitude : 1.5 mm
2) Sweep rate : 10-55-10Hz for 1 minute
3) Sweep method : Logarithmic frequency
sweep rate
4) Vibration direction : X,Y,Z(3 directions)
+ 0.15
mm
- 0.15
No damage
(Electrical and
mechanical)
No.5.1 and
5.2.1 to 5.2.2 shall
be satisfied.
5) Time : Each direction 2 hours
(Total 6 hours)
5.2.5 Soldering
heat test
Mount the switch on P.W.B by adhesive.
1) Reflow process 2 times.
(Refer to section 6.1)
2) Standard conditions after test : 1 hours
No.5.1 and
No.5.2.1 to 5.2.2
shall be satisfied.
5.2.6 Solderbility
After spreading flux, the terminal is immersed
in solder with following condition.
Solder ber : M705/Sn-3.0Ag-0.5Cu
(Senju Metal Indusry Co.,Ltd.)
Flux : CF-110VH-2A (tamura kaken)
Soldering temperture : 260±5℃
Soldering time : 2±0.5 sec.
95% or more of surface
area(Excluding ruptured
surface)where is
immersed in solder
shall be covered by new
solder.
Panasonic Electronic Devices Malaysia Sdn. Bhd.
Classification
Issue No.
20091134
REFERENCE SPECIFICATION
Part Name
LIGHT TOUCH SWITCH
Part No.
5/9
EVQP0N02B
5.3 Climatic characteristics
No.
ITEM
TEST CONDITION
PERFORMANCE
5.3.1 Cold test
1)
2)
3)
4)
Temperature : -40±2 ℃
Duration of test : 500 h
Take off a drop water.
Standard conditions after test : 1 h
Contact resistance
200 mΩ max.
No.5.1.2 to 5.1.4 and
No.5.2.1 to 5.2.2
shall be satisfied.
5.3.2 Heat test
1) Temperature : 85±2 ℃
2) Duration of test : 500 h
3) Standard conditions after test : 1 h
Contact resistance
200 mΩ max.
No.5.1.2 to 5.1.4 and
No.5.2.1 to 5.2.2
shall be satisfied.
5.3.3 Heat shock
test
1) Test cycles : 20 cycles
2) Standard conditions after test : 1 h
Contact resistance
200 mΩ max.
No.5.1.2 to 5.1.4 and
No.5.2.1 to 5.2.2
shall be satisfied.
A:+85±2 ℃
B:-40±2 ℃
C:1 hour
D:5 minutes max.
E:1 hour
F:5 minutes max.
5.3.4 Humidity test
1)
2)
3)
4)
5)
Temperature : 60±2 ℃
Relative humidity : 90～95 %
Duration of test : 500 h
Take off a drop water.
Standard conditions after test : 1 h
5.3.5 Endurance
(Switching
action)
1) DC 15 V 20 mA Resistance load
2) Operation speed : 2～3 times/s
3) Push force : Maximum value of operation
force
4) Operation number : 2,000,000 times
Contact resistance
2000m Ω max.
Bouncing : 10 ms max.
Variation rate of
operation force shall
be within ±30 % to the
value before testing
No.5.1.2 and 5.2.2
shall be satisfied.
5.3.6 Withstand H 2 S
1)
2)
3)
4)
5)
Contact resistance
200 mΩ max.
No.5.1.2 to 5.1.4 and
No.5.2.1 to 5.2.2
shall be satisfied.
Density : 3±1 ppm
Temperature : 40±2 ℃
Relative humidity : 80～85 %
Duration of test : 24 h
Standard conditions after test : 1 h
Contact resistance
200 mΩ max.
No.5.1.2 to 5.1.4 and
No.5.2.1 to 5.2.2
shall be satisfied.
Panasonic Electronic Devices Malaysia Sdn. Bhd.
Classification
Issue No.
20091134
REFERENCE SPECIFICATION
Part Name
LIGHT TOUCH SWITCH
Part No.
6/9
EVQP0N02B
6. Prohibitions and precaution for handling
6.1 Reflow soldering condition
1) Two times max. with directing the switch mounting side of P.W.B up.
2) Re-soldering by soldering iron shall be allowed under 350℃ max. 3 sec. max. 1 time only
and the tip of iron must not touch to terminals.
Soldering iron for re-soldering have to be 60W max.
6.2 Design instructions
1) Please refer to the land pattern plan Panasonic recommends on the 2nd page.
2) The key top shall have flat area on the top as Dia 2mm or greater than it.
3) The deflection of key top when switch is actuated shall be whithin 10° as fig-1.
4) The center of key top for switch operation needs to locate within 1mm max.
5) Pre-load on the switch between key top and switch shall be 0.2mm max. as fig-2.
If you have any question about above instruction and any devation
per our recommendation,let us know.
6.3
1)
2)
3)
fig-1
fig-2
Notes
Please be cautions not to give excessive static load or shock to switches.
Please be careful not to pile up P.W.B. after switches were soldered.
Preservation under high temperature and high humidity or corrosive gas should be avoided
especially. When you need to preserve for a long period, do not open the carton.
4) Cleaning
･If flux or solder is scattered on the surface of P.W.B when soldering, characteristics
of this product may be damaged.
･Cleaning after soldering is not allowed.When cleaning is required this switch should be
soldered after the cleaning.
5) Avoid the use of the switch under pushed ON condition is continued for a long time.
6) There is a possibility the flux from solder paste infiltrates into the body if plenty of
solder paste was applied by switch on the P.W.B.
So we recommend to use our proposed land design in order to prevent above problem.
Also please avoid putting additional land by the switch on the P.W.B.
Panasonic Electronic Devices Malaysia Sdn. Bhd.
Classification
Issue No.
20091134
REFERENCE SPECIFICATION
Part Name
LIGHT TOUCH SWITCH
Part No.
EVQP0N02B
7. Packing specification
Panasonic Electronic Devices Malaysia Sdn. Bhd.
7/9
Classification
Issue No.
20091134
REFERENCE SPECIFICATION
Part Name
LIGHT TOUCH SWITCH
Part No.
EVQP0N02B
SECTIONAL DRAWING
PART LIST
Panasonic Electronic Devices Malaysia Sdn. Bhd.
8/9
Classification
Issue No.
20091134
REFERENCE SPECIFICATION
Part Name
LIGHT TOUCH SWITCH
Part No.
EVQP0N02B
9/9
<Prohibitions and precaution for handling>
【Prohibited items on fire and smoking】
・Absolutely avoid use of a product beyond its rated range because doing so may cause a fire.
If misuse or abnormal use may result under conditions in which the product is used out of its
rated range,take proper measures such as current interruption using a protective circuit.
・The grade of nonflammability for resin used in product is "94HB," which is based on UL94
Standards (flammability test for plastic materials). Prohibit use in a location where a
spreading fire may be generated or prepare against a spreading fire.
【For use in equipment for which safety is requested】
・Although care is taken to ensure product quality,inferior characteristics,short circuits,
and open circuits are some problems that might be generated, To design an equipment which
places maximum emphasis on safety,review the effect of any single fault of a product
in advance and perform virtually fail-safe design to ensure maximum safety by:
･Preparing a protective circuit or a protective device to improve system safety,and equipment.
･Preparing a redundant circuit to improve system safety so that the single fault
of a product does not cause a dangerous situation.
【Attentions required for storage condition】
・When this product is to be stored in the following circumstances and conditions,it may
affect on the performance deteriorations and solderability etc.,avoid storing in the
following conditions.
(1)A place where the temperature is -10℃ max.,+40℃ min. and the humidity is 85% min.
(2)In the corrosive gas atmosphere.
(3)Long-term storage for 6 months min.
(4)A place where the product is exposed to direct sunlight.
・Store in packed condition so that the load stress is not applied.
・Please use this product as soon as possible,our recommendation is within 3 months and the
1imitation is 6 months.
・If any remainder left after packing is opened,store it with proper moistureproofing and
gasproofing,etc.,
Panasonic Electronic Devices Malaysia Sdn. Bhd.