Toggles Series CB Rockers General Specifications Pushbuttons Electrical Capacity (Resistive Load) Low/Logic Level: 50mA @ 24V DC maximum Programmable Illuminated PB Other Ratings Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Nominal Operating Force: Total Travel: 100 milliohms maximum 100 megohms minimum @ 250V DC 250V AC minimum between contacts & between contacts & case for 1 minute minimum 100,000 operations minimum 100,000 operations minimum 1.57N .010” (.250mm) Keylocks Materials & Finishes Rotaries Slides Tactiles Tilt Touch 6mm Process Sealed Tactiles Actuator: Case: Seal: Base: Movable Contacts: Stationary Contacts: Terminals: Glass fiber reinforced polyamide (UL94V-0) Stainless steel Polytetrafluoroethylene Polyphthalamide (UL94V-0) Beryllium copper with silver plating Brass with silver plating Brass with silver plating Environmental Data J Operating Temperature Range: Humidity: Vibration: Shock: –25°C through +70°C (–13°F through +158°F) 90 ~ 95% humidity for 96 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) PCB Processing Soldering: Wave Soldering Recommended. See Profile A in Supplement section. Manual Soldering: See Profile A in Supplement section. Cleaning: Automated cleaning. See Cleaning specifications in Supplement section. Flammability Standards: UL94V-0 actuator & base The CB Series tactiles have not been tested for UL recognition or CSA certification. These switches are designed for use in a low-voltage, low-current, logic-level circuit. When used as intended in a logic-level circuit, the results do not produce hazardous energy. Supplement Accessories Indicators Standards & Certifications J4 www.nkk.com Toggles Series CB 6mm Process Sealed Tactiles Rockers Distinctive Characteristics Programmable Illuminated PB Pushbuttons Sealed construction prevents contact contamination and allows automated soldering and cleaning. .244” (6.2mm) square body allows compact mounting. Actuator and base meet UL flammability rating of 94V-0. Rotaries Keylocks Dome contact gives crisp tactile feedback to positively indicate circuit transfer and assures high reliability and long life – more than 100,000 operations. Insert molded terminals lock out flux, solvents, and other contaminants. J Indicators Touch Tilt Packaged in stick tube or partitioned tray. Tactiles Slides Crimped terminals ensure secure mounting and prevent dislodging during wave soldering. Supplement Accessories Actual Size www.nkk.com J5 Series CB Toggles 6mm Process Sealed Tactiles TYPICAL SWITCH ORDERING EXAMPLE 15 F P Programmable Illuminated PB Pushbuttons Rockers CB Actuator Pole & Circuit 15 SPST OFF F (ON) Packaging Terminals P Flat Button S Stick-Tube 50 Pieces/Tube No Code Partitioned Tray Straight PC ( ) = Momentary Keylocks DESCRIPTION FOR TYPICAL ORDERING EXAMPLE CB15FP Rotaries Flat Button SPST OFF-(ON) Circuit Slides Straight PC Terminals Tactiles POLE & CIRCUIT Actuator Position ( ) = Momentary J Normal Tilt Pole Switch Throw & Schematic Down Model SPST CB15 OFF 3 2 4 (ON) Touch SP 1 Note: Terminal numbers are not actually on the switch. TYPICAL SWITCH DIMENSIONS Accessories Indicators Single Pole • Single Throw (3.0) Dia .118 (0.3) Typ .012 (6.2) .244 (6.5) .256 Supplement (4.35) Dia .171 (6.2) .244 (0.65) .026 (3.1) .122 3 2 (3.5) .138 CB15FP J6 1 www.nkk.com 4 (4.0) .157 (0.7) Typ .028 3 1 4 2 (4.0) .157 (6.5) .256 (1.0) Dia Typ .039 Series CB Toggles 6mm Process Sealed Tactiles PACKAGING Rockers Stick-Tube Pushbuttons Switches must be ordered in 50-piece increments when stick-tube packaging is selected. Programmable Illuminated PB Partitioned Tray If ordered in less than 50-piece increments, the switches are packaged in a partitioned tray. (340.0) 13.386 Rotaries (12.0) .472 Slides (11.0) .433 KEYBOARD MATRIX Common Bus Matrix X-Y Matrix These single pole, single throw switches can be used in a keyboard matrix and, using strapped terminals, achieve a common bus electrical configuration on a single-sided PC board. 10 6 4 7 8 9 3 11 8 A B 0 1 2 12 1 5 4 6 2 7 8 9 6 A B 0 7 = ON 5 7 Red = PCB Trace 4 Tilt P C Te r m i na t i ons 1 2 3 4 5 6 7 1 2 3 4 5 6 7 8 9 0 A B = ON 3 Supplement 6 1 2 3 4 5 6 7 8 9 0 A B 3 2 1 P C Te r m i n a t i o n s 1 2 3 4 5 6 7 8 9 10 11 12 13 Keys (Switches) 5 4 13 Keys (Switches) 3 2 Black = Switch Circuit www.nkk.com Touch 9 5 1 J These single pole, single throw switches can be arranged on a single-sided PC board matrix with strapped terminals to achieve an X-Y type electrical interconnection. Tactiles Each stick-tube contains 50 switches Keylocks Stick-Tube Dimensions Indicators No Code Accessories S J7