Toggles Series JL Rockers General Specifications Electrical Capacity (Resistive Load) Pushbuttons 50mA @ 24V DC Other Ratings Programmable Illuminated PB Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Nominal Operating Force: Total Travel: Materials & Finishes Rotaries Keylocks Actuator: Case: Base: Movable Contact: Stationary Contacts: Switch Terminals: Lamp Terminals: 50 milliohms maximum 500 megohms minimum @ 250V DC 250V AC minimum for 1 minute minimum 1,000,000 operations minimum 1,000,000 operations minimum 3.0N .030” (0.75mm) Polycarbonate Glass fiber reinforced polyamide Glass fiber reinforced polybutylene terephthalate (PBT) Stainless steel Brass with silver plating Brass with silver plating Brass with tin plating Environmental Data Slides Tactiles Tilt Touch Low/Logic Level: J Operating Temperature Range: –25°C through +50°C (–13°F through +122°F) Humidity: 90 ~ 95% humidity for 240 hours @ 40°C (104°F) Vibration: 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours Shock: 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) PCB Processing Soldering: Cleaning: Standards & Certifications Wave Soldering: See Profile A in Supplement section. Manual Soldering: See Profile A in Supplement section. These devices are not process sealed. Hand clean locally using alcohol based solution. The JL Series tactiles have not been tested for UL recognition or CSA certification. These switches are designed for use in a low-voltage, low-current circuit. When used as intended, the results do not produce hazardous energy. Supplement Accessories Indicators Illuminated Ultra-Thin Tactiles J46 www.nkk.com Series JL Toggles Illuminated Ultra-Thin Tactiles Rockers Distinctive Characteristics Pushbuttons Bright, full face illumination with choice of red, green, or amber LEDs. Programmable Illuminated PB Multiple LED arrays and interior reflectors enhance illumination of the large, .75” (19mm) square actuator surface. Distinctive design allows full face illumination in extra low profile of 0.31” (7.85mm) from PCB to top of switch. Keylocks Dome contact gives crisp tactile and audible feedback with short stroke and assures high reliability and long life of 1,000,000 operations. Crimped terminals provide a spring type action to ensure secure mounting and prevent dislodging during the soldering process. Rotaries Actual Size Slides Streamlined housing dimensions provide for compact, side-by-side mounting on a standard grid. Common Bus Matrix X-Y Matrix These single pole, single throw switches can be used in a keyboard matrix and, using strapped terminals, achieve a common bus electrical configuration on a single-sided PC board. 7 8 9 3 11 8 A B 0 1 2 12 6 2 7 8 9 6 A B 0 7 = ON 5 7 Red = PCB Trace 4 Tilt 3 Black = Switch Circuit www.nkk.com Touch Indicators 6 4 5 4 P C Te r m i na t i ons 1 2 3 4 5 6 7 1 2 3 4 5 6 7 8 9 0 A B = ON Accessories 10 1 Supplement 6 1 2 3 4 5 6 7 8 9 0 A B 3 2 1 P C Te r m i n a t i o n s 1 2 3 4 5 6 7 8 9 10 11 12 13 Keys (Switches) 5 13 Keys (Switches) 3 2 4 These single pole, single throw switches can be arranged on a single-sided PC board matrix with strapped terminals to achieve an X-Y type electrical interconnection. 9 5 1 J Tactiles Terminal spacing conforms to standard .100” (2.54mm) PCB grid. J47 Series JL Toggles Illuminated Ultra-Thin Tactiles TYPICAL SWITCH ORDERING EXAMPLE Pushbuttons Rockers JL 15 SK S Pole & Circuit 15 SPST OFF C C Terminals Actuator Shape S (ON) Square Programmable Illuminated PB Housing & Color Actuator Colors Keylocks Square Black Silver Contacts Straight PC P2 ( ) = Momentary SK P2 LED Colors B White C Red C Red D Amber D Amber F Green F Green DESCRIPTION FOR TYPICAL ORDERING EXAMPLE Rotaries JL15SKSCCP2 Tactiles Slides Red Square Actuator with Red LED Square Black Housing SPST OFF-(ON) Circuit Silver Contacts Straight PC Terminals J POLE & CIRCUIT Tilt Actuator Position ( ) = Momentary Touch Normal Pole Model SP JL15 Switch Throw & Schematic 1 SPST OFF LED Schematic Down 1a (+) 1 1a (ON) Indicators HOUSING & COLOR Accessories SK (-) Note: Terminal markings “1”, “1a”, “–”, and “+” are shown on the switch. ACTUATOR SHAPE & COLORS Square Black Housing S .748” (19.0mm) Square Actuator Actuator Colors Available: Supplement B J48 www.nkk.com White C Red D Amber F Green Series JL Toggles Illuminated Ultra-Thin Tactiles LED COLORS & SPECIFICATIONS (–) Amber & Green models (+) each have 8 LEDs. (–) D Red Amber F Green Pushbuttons (+) C Color Forward Peak Current I FM 75mA 100mA 100mA Typical Forward Current IF 60mA 80mA 80mA Forward Voltage VF 4.0V 4.2V 4.2V Reverse Peak Voltage VRM 8V 8V 8V Current Reduction Rate Above 25°C ∆I F 0.98mA/°C 1.31mA/°C 1.31mA/°C Programmable Illuminated PB 1-color, 1-element LEDs grouped in arrays of 6 or 8. –25°C ~ +50°C Ambient Temperature Range TERMINALS Silver Contacts Straight PC Additional details in Typical Switch Dimensions Keylocks P2 Square Actuator (0.8) Typ .031 (0.3) Typ .012 1 1a 1a 1 + (20.32) .800 Slides (19.0) Sq .748 – (20.32) .800 (0.8) Dia .031 1 (0.15) .006 (7.85) .309 1a 1a (10.16) .400 (15.24) .600 (3.6) .142 J 1 (10.16) .400 (15.24) .600 (1.0) Dia Typ .039 Tilt (20.4) Sq .803 (22.0) Sq .866 Rotaries TYPICAL SWITCH DIMENSIONS Tactiles Red LED model has 6 LEDs. Rockers LEDs are an integral part of the switch. The electrical specifications shown are determined at a basic temperature of 25°C. If the source voltage exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by using the formula in the Supplement. JL15SKSCCP2 Touch LEGENDS Recommended Print Methods: Engraving is not recommended as an additional method for legends. Screen Print or Pad Print. (17.48) Sq .688 (19.0) Sq .748 (0.76) Typ .030 Epoxy based ink is recommended. www.nkk.com Contact factory if engraving is required; it must be done before the actuator is assembled. J49 Accessories Additional Method Supplement ER W PO Shaded area is printable area. Indicators NKK Switches can provide custom legends for caps. Contact factory for more information.