Smallest Process Indicator & Controller

Smallest
Process Indicator & Controller
Panel Mount for Easy Installation!
IS-S0108 Process Indicator & Controller
Application program customized by NKK
Ideal for applications that require quick design cycles and ease of use.
Simply install and run.
Features:
• Panel mount for easy installation
• Onboard microprocessor for simple control applications
• Built-in display
• LCD 36 x 24 pixels
• Red, green, and amber backlighting
• Display graphics or up to 3 lines of text (6 characters each)
• Character generator (2 fonts)
• Store up to 35 images
• Built-in I/O
• Pushbutton switch (single pole momentary)
• 8 configurable inputs/outputs
– Up to 8 digital inputs/outputs
– Up to 4 analog inputs
– Serial communication
• Inputs and outputs connect via PCB solder points or 14 pin header
Specifications:
Bottom View
Size is a fraction of typical
process indicators and controllers
• Operating Temperature: 0°C ~ +40°C
• Input Voltage: 9 ~ 15V DC
Built-in
pushbutton
with display
Hardware Customization Options:
•
•
•
•
Higher current outputs
Extended temperature range (-20°C ~ +60°C)
Terminal blocks or other connections for I/O
OLED display (PCB mount)
I/O
points
Dimensions:
(27.6)
1.087
(23.2)
.913
(31.5)
1.240
(29.0)
1.142
Panel Height
Below: .751” (19.53mm)
Above: .079” (2.0mm)
Panel Thickness Range
.059 ~ .157"
(1.5mm ~ 4.0mm)
(23.7)
.933
SmartSwitch Just Got Smarter!
Now with MicroProcessor and Real World I/O
The Process Indicator & Controller can be used in
many applications. It excels in displaying analog
measurements such as music volume, water flow,
or illumination level. This device can be used in
a bank of displays where many measurements
can be viewed at once. If panel space is tight,
one device can display multiple measurements
in a sequence or the operator can scroll through
displays.
Medical Equipment
This device displays up to 35 images to provide
status and process condition information to
operators. At a glance, condition is shown
using the red, green, and amber backlighting.
Graphic images can display numeric values
in a variety of formats including dial gauges.
Output commands can be sent out automatically
based on pre-programmed values or input from
operators.
Heat Sensor
Function Examples
1. Display predefined images based on status of
up to 8 total inputs.
4. Display the status of up to 4 analog gauges as
bar graphs, percentages, or predefined images.
2. Change backlight colors based on inputs then
automatically toggle other devices based on
defined values.
5. Use digital input/output lines to turn device on
or off based on the status of input/outputs or
timer or counter.
3. Use device as a counter or timer and display
results.
6. Display process variables and conditions
by pressing the built-in pushbutton.
High End Camera
(Courtesy of Noventri)
Restaurant Equipment
Application Examples
Medical Packaging
Restaurant Equipment
Motor Monitoring
Controller is connected to
equipment which drops pills
into a bag. When the controller
counts a fixed number of pills, it
then triggers another device to
seal the bag, and send it to the
next station.
Controller is used as a food
timer where it is hooked up to
a heating element. When the
switch is pressed, the burger
is cooked for a fixed time until
the controller switches the
heating element off. It can also
be hooked up to a temperature
sensor indicating the burger is
cooked correctly.
Process indicator is hooked up
to a motor controller and a load
sensor. When the load becomes
too high, the indicator flashes
red, alerting the operator that
an action is required. The
process indicator then sends a
shut down signal to the motor
controller.
Smallest Process Indicator & Controller on the Market!
Phone 480.991.0942 • Toll Free 877.228.9655
www.nkkswitches.com
7850 East Gelding Drive • Scottsdale, Arizona 85260
0411