PI74AVC164245

PI74AVC164245
16-Bit 1.2-2.5V to 3.3V Level Shifting
Transceiver with 3-State Outputs
Features
Description
ÎÎPI74AVC164245 is designed for low voltage operation:
Pericom Semiconductor’s PI74AVC164245, a 16-bit (dual-octal)
noninverting bus transceiver, contains two separate supply rails:
B port (VCCB), set at 3.3V, and A port (VCCA), set to operate
at 1.2-2.5V. This arrangement permits translation from a 1.2-2.5V
to 3.3V environment and vice versa.
1.2V - 2.5V to 3.3V
ÎÎIndustrial
operation at –40°C to +85°C
ÎÎPackaging
(Pb-free & Green):
– 48-pin plastic 300-mil SSOP (V)
– 48-pin plastic 240-mil TSSOP (A)
– 48-pin plastic 173-mil TVSOP (K)
The PI74AVC164245 is designed for asynchronous communication
between data buses.
To ensure the high impedance state during power up or power
down, the output-enable (OE) input should be tied to VCCB through
a pullup resistor: the minimum value of the resistor is determined
by the current-sinking capability of the driver.
Truth Table (each 8-bit section)
Inputs
Operation
OE
DIR
L
L
H
L
H
X
B data to A bus
A data to B bus
Isolation
Pin Configuration (28-Pin TQFN)
Block Diagram
1DIR
1
48
1A1
1OE
47
2
1B1
To Seven Other Channels
2DIR 24
25
2A1
2OE
36
13
2B1
To Seven Other Channels
12-0208
1
(3.3V LVTTL) 1DIR
1
48
1OE (3.3V LVTTL)
1B1
2
47
1A1
1B2
3
46
1A2
GND
4
45
GND
1B3
5
44
1A3
1B4
6
43
1A4
(3.3V) VCCB
7
42
VCCA (1.2V-2.5V)
1B5
8
41
1A5
1B6
9
40
1A6
GND
10
39
GND
1B7
11
38
1A7
1B8
12
37
1A8
2B1
13
36
2A1
2B2
14
35
2A2
GND
15
34
GND
2B3
16
33
2A3
2B4
17
32
2A4
(3.3V) VCCB
18
31
VCCA (1.2V-2.5V)
2B5
19
30
2A5
2B6
20
29
2A6
GND
21
28
GND
2B7
22
27
2A7
2B8
23
26
2A8
(3.3V LVTTL) 2DIR
24
25
2OE (3.3V LVTTL)
www.pericom.com P-0.107/18/12
PI74AVC164245
16-Bit 1.2-2.5V to 3.3V Level Shifting Transceiver with 3-State Outputs
Maximum Ratings
(Absolute maximum ratings over operating free-air temperature range from VCCB at 3.3V & VCCA at 1.5 - 2.5V, unless otherwise
Note:
Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating
only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this
specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability.
Supply Voltage Range
Input Voltage Range, VI
VCCA........................ –0.5V to 3.8V
VCCB....................... –0.5V to 4.6V
Continuous output current, IO......................................... ±50mA
Continuous current through each VCC or GND............ ±100mA
Package thermal impedance, 0JA(3): A package.............. 89°C/W
K package............................. 58°C/W
V package............................. 94°C/W
Storage temperature range, TSTG....................... –65°C to 150°C
Except I/O ports(1).. –0.5V to 4.6V
I/O port A(2)... –0.5V to VCCA+0.5V
I/O port B(1)... –0.5V to VCCB+0.5V
Input Clamp Current IIK(V1<0)................................. –50mA
Ouput Clamp Current IOK(VO<0).............................. –50mA
Recommended Operating Conditions for VCCB at 3.3V(4)
Min.
Max.
3.0
3.6
Units
VCCB
Supply voltage
VIH
High-level voltage
VIL
Low-level voltage
VIB
Input Voltage
0
VCCB
VOB
Output Voltage
0
VCCB
IOH
High-level output current
–12
IOL
Low-level output current
12
Dt/Dv
Input transition rise or fall rate
10
ns/V
TA
Operating free-air temperature
85
°C
12-0208
2
0.8
–40
2
V
mA
www.pericom.com P-0.107/18/12
PI74AVC164245
16-Bit 1.2-2.5V to 3.3V Level Shifting Transceiver with 3-State Outputs
Recommended Operating Conditions for VCCA at 2.5V(4)
Min.
Max.
2.3
2.7
VCCA
Supply voltage
VIH
High-level voltage
VCCA = 2.3V to 2.7V
VIL
Low-level voltage
VCCA = 2.3V to 2.7V
VIA
Input Voltage
0
VCCA
VOA
Output Voltage
0
VCCA
IOH
High-level output current
IOL
Low-level output current
Dt/Dv
Input transition rise or fall rate
TA
Operating free-air temperature
Units
1.7
V
0.7
VCCA = 2.3V
-8
VCCA = 2.7V
–12
VCCA = 2.3V
8
VCCA = 2.7V
12
–40
mA
10
ns/V
85
°C
Notes:
1. This value is limited to 4.6V maximum.
2. This value is limited to 3.8V maximum.
3. The package thermal impedance is calculated in accordance with JESD 51.
4. To ensure proper device operation, all unused device inputs must be held at the associated VCC or GND.Î
Î
Recommended Operating Conditions for VCCA at 1.8V(4)
Min.
Max.
1.65
1.95
VCCA
Supply voltage
VIH
High-level voltage
VCCA = 1.65V to 1.95V
VIL
Low-level voltage
VCCA = 1.65V to 1.95V
VIB
Input Voltage
0
VCCA
VOA
Output Voltage
0
VCCA
IOH
High-level output current
IOL
Low-level output current
Dt/Dv
Input transition rise or fall rate
TA
Operating free-air temperature
Units
0.65 x VCCA
0.35 x VCCA
VCCA = 1.65V
-4
VCCA = 1.95V
–8
VCCA = 1.65V
4
VCCA = 1.95V
8
–40
V
mA
10
ns/V
85
°C
Notes:
1. To ensure proper device operation, all unused device inputs must be held at the associated VCC or GND.
12-0208
3
www.pericom.com P-0.107/18/12
PI74AVC164245
16-Bit 1.2-2.5V to 3.3V Level Shifting Transceiver with 3-State Outputs
Electrical Characteristics (VCCB) (Over recommended operating free-air temperature range for VCCB = 3.3V)
Parameter
Test Conditions
VCCB
IOH = –100mA
VOH (A to B)
IOH = –12mA
IOL = –100mA
VOL (A to B)
IOL = –12mA
Min.
3.0V
2.8
3.6V
3.4
3.0V
2.2
3.6V
2.8
Typ.†
Max.
3.0V
0.2
3.6V
0.2
3.0V
0.5
3.6V
0.5
II
Control Inputs
VI = VCCB or GND
3.6V
±5
IOZ‡
A or B ports
VO = VCCB or GND
3.6V
±10
ICC
VI = VCCB or GND, IO = 0
3.6V
20
DICC*
One input at VCCB –0.6V, Other inputs at
VCCB or GND
3.0V to
3.6V
500
CI
Control Inputs VI = VCCB or GND
3.3V
4.5
CIO
A or B ports
3.3V
6.5
VO = VCCB or GND
Units
V
µA
pF
Notes:
† Typical values are measured at VCCB = 3.3V, TA = 25°C
‡ For I/O ports, the parameter IOZ includes the input leakage current.
* This is the increase in supply current for each input that is at one of the specified TTL voltage levels rather than at 0 or the associated VCC.
12-0208
4
www.pericom.com P-0.107/18/12
PI74AVC164245
16-Bit 1.2-2.5V to 3.3V Level Shifting Transceiver with 3-State Outputs
Electrical Characteristics (VCCA) (Over recommended operating free-air temperature range for VCCA = 2.5V)
Parameter
Test Conditions
VCCA
VOL (B to A)
Typ.†
Max.
Units
2.3V to 2.7V VCC - 0.1
IOH = –100mA
VOH (B to A)
Min.
2.3V
1.7
IOH = –8mA
2.3V
2.0
IOH = –12mA
2.7V
1.8
IOL = –100mA
2.3V to 2.7V
0.2
IOL = –8mA
2.3V
0.4
IOL = –12mA
2.7V
0.5
V
II
Control Inputs
VI = VCCA or GND
2.7V
±5
IOZ‡
A or B ports
VO = VCCB or GND
2.7V
±10
ICC
VI = VCCA or GND, IO = 0
2.7V
30
DICC*
One input at VCCA–0.6V,
Other inputs at VCCA or GND
2.3V to 2.7V
500
CI
Control Inputs VI = VCCA or GND
2.5V
4.5
CIO
A or B ports
2.5V
6.5
VO = VCCA or GND
µA
pF
Notes:
† Typical values are measured at VCCA = 2.5V, TA = 25°C
‡ For I/O ports, the parameter IOZ includes the input leakage current.
* This is the increase in supply current for each input that is at one of the specified TTL voltage levels rather than at 0 or the associated VCC.
12-0208
5
www.pericom.com P-0.107/18/12
PI74AVC164245
16-Bit 1.2-2.5V to 3.3V Level Shifting Transceiver with 3-State Outputs
Electrical Characteristics (VCCA) (Over recommended operating free-air temperature range for VCCA = 1.8V)
Parameter
Test Conditions
VCCA
Min.
Typ.** Max.
1.65V to
1.95V
VCC - 0.1
1.65V
1.3
1.95V
1.4
IOH = –8mA
1.95V
1.3
IOL = 100mA
1.65V
0.2
IOL = 4mA
1.95V
0.3
IOL = 8mA
1.95V
0.4
VO = VCCA or GND
1.95V
±5
ICC
VI = VCCA or GND, IO = 0
1.95V
±20
DICC*
One input at VCCA– 6V,
Other inputs at VCCA or GND
1.65V to
1.95V
300
IOH = –100mA
VOH (B to A)
IOH = –4mA
VOL (B to A)
IOZ***
A or B ports
V
CI
Control Inputs VI = VCCA or GND
1.8V
4.5
CIO
A or B ports
1.8V
6.5
VO = VCCA or GND
Units
µA
pF
Notes:
*
The increase in supply current for each input at one of the specified TTL voltage levels rather than at the associated VCC.
** Typical values are measured at VCCA = 1.8V, TA = 25°C
*** For I/O ports, the parameter IOZ includes the input leakage current.
12-0208
6
www.pericom.com P-0.107/18/12
PI74AVC164245
16-Bit 1.2-2.5V to 3.3V Level Shifting Transceiver with 3-State Outputs
Recommended Operating Conditions for VCCA at 1.2V
Min.
Typ.
Max.
Units
0.35 x VCCA
V
VCCA
Supply voltage
1.2V
VIH
High-level voltage
VCCA = 1.2V
VIL
Low-level voltage
VCCA = 1.2V
VIB
Input Voltage
0
VCCA
VOA
Output Voltage
0
VCCA
IOH
High-level output current
VCCA = 1.2V
-2
IOL
Low-level output current
VCCA = 1.2V
2
Dt/Dv
Input transition rise or fall rate
TA
Operating free-air temperature
0.65 x VCCA
–40
mA
10
ns/V
85
°C
Notes:
1. To ensure proper device operation, all unused device inputs must be held at the associated VCC or GND.
Electrical Characteristics (VCCA) (Over recommended operating free-air temperature range for VCCA = 1.2V)
Parameter
Test Conditions
VOH (B to A)
VOL (B to A)
IOZ**
A or B ports
ICC
VCCA
Min.
Typ.
Max.
IOH = –2mA
1.2V
1.1V
IOL = 100mA
1.2V
0.1
IOL = 2mA
1.2V
0.1
VO = VCCA or GND
1.2V
±5
VI = VCCA or GND, IO = 0
1.2V
10
CI
Control Inputs VI = VCCA or GND
1.2V
4.5
CIO
A or B ports
1.2V
6.5
VO = VCCA or GND
Units
µA
pF
Notes:
*
The increase in supply current for each input at one of the specified TTL voltage levels rather than at the associated VCC.
** For I/O ports, the parameter IOZ includes the input leakage current.
12-0208
7
www.pericom.com P-0.107/18/12
PI74AVC164245
16-Bit 1.2-2.5V to 3.3V Level Shifting Transceiver with 3-State Outputs
Switching Characteristics (CL = see Figures 1,2,3,4)
PI74AVC164245A
VCCB = 3.3V ±0.3V
VCCB = 3.3V ±0.3V
VCCA = 1.8V
±0.15V
VCCA = 2.5V
±0.2V
VCCA = 1.2V
VCCA = 1.8V
±0.15V
VCCA = 2.5V Units
±0.2V
From
(Input)
To
(Output)
Min.
Max.
Min.
Max.
Typ.
Min.
Max.
A
B
1.5
4.6
1.5
4.2
3.5
1.5
3.5
1.0
3.0
B
A
1.5
4.4
1.5
4.0
3.0
1.5
3.5
1.0
2.8
tEN
OE
B
1.7
5.5
1.7
4.5
2.8
1.7
4.5
1.2
3.5
tDIS
OE
B
1.5
5.5
1.5
4.5
2.2
1.5
4.5
1.0
3.5
tEN
OE
A
1.7
5.5
1.7
4.5
4.2
1.7
4.5
1.2
3.5
tDIS
OE
A
2.0
5.5
2.0
4.5
3.3
2.0
4.5
1.5
3.5
Parameter
tPD
t
PI74AVC164245
(1)
SK(O)
t
(1)
SK(b)
Min. Max.
0.5
0.3
0.3
0.25
ns
Notes:
1. This is the skew between any two outputs of the same package, and switching in the same direction. For tSK(O) ,Output 1 and Output 2 are any two
outputs. For tSK(b), Output 1 and Output 2 are on the same bank.
Operating Conditions for TA = 25 ºC
VCCA = 2.5V
VCCB = 3.3V
Test Conditions
Typical
Outputs Enabled (A or B)
CL = 30pF
56
Outputs Disabled
F = 10MHz
6
Parameters
CPD Power Dissipation Capacitance
12-0208
8
Units
pF
www.pericom.com P-0.107/18/12
PI74AVC164245
16-Bit 1.2-2.5V to 3.3V Level Shifting Transceiver with 3-State Outputs
Parameter Measurement Information, VCCO = 1.2V
VIN
From Output
Under Test
Open
GND
CL = 15pF
Test
S1
tPD
tPLZ/ tPZL
tPHZ/ tPZH
Open
2 x VCCO
2 × VCC
2000Ω
2000Ω
Output
Control
(low-level
enabling)
Input
VCCI/2
VCCI/2
tPHL
tPLH
Output
0V
tPZH
VOH
Output
Waveform 2
S1 at GND
VCCO/2
VOL
VCCO/2
VCCI/2
Output tPZL
Waveform 1
S1 at 2xVCCO
VCCI
GND
VCCI/2
tPLZ
VCCO/2
tPHZ
VCCO/2
VCCI
0V
VCCO
VOL+0.1V
VOL
VOH
VOH –0.1V
0V
Voltage Waveforms
Enable and Disable Times
Figure 1. Load Circuit and Voltage Waveforms
Notes:
CL includes probe and jig capacitance.
Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control.
All input pulses are supplied by generators having the following characteristics: PRR ≤10Mz, ZO = 50Ω, tR ≤ 2.5ns, tF ≤ 2.5ns.
The outputs are measured one at a time with one transition per measurement.
tPLZ and tPHZ are the same as tDIS.
tPZL and tPZH are the same as tEN.
tPLH and tPHL are the same as tPD.
12-0208
9
www.pericom.com P-0.107/18/12
PI74AVC164245
16-Bit 1.2-2.5V to 3.3V Level Shifting Transceiver with 3-State Outputs
Parameter Measurement Information, VCCO = 1.8V ± 0.15V
VIN
From Output
Under Test
2 × VCC
1000Ω
Open
Test
S1
tPD
tPLZ/ tPZL
tPHZ/ tPZH
Open
2 x VCCO
GND
CL = 30pF
1000Ω
Output
Control
(low-level
enabling)
VCCI
Input
VCCI/2
VCCI/2
tPHL
tPLH
Output
VCCI/2
VCCO/2
tPZH
tPHZ
Output
Waveform 2
S1 at GND
VCCO/2
VOL
VCCO/2
VCCI
VCCI/2
Output tPZL
Waveform 1
S1 at 2xVCCO
0V
VOH
GND
tPLZ
VCCO/2
0V
VCCO
VOL+0.15V
VOL
VOH
VOH –0.15V
0V
Voltage Waveforms
Enable and Disable Times
Figure 2. Load Circuit and Voltage Waveforms
Notes:
CL includes probe and jig capacitance.
Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control.
All input pulses are supplied by generators having the following characteristics: PRR ≤10Mz, ZO = 50Ω, tR ≤ 2.5ns, tF ≤ 2.5ns.
The outputs are measured one at a time with one transition per measurement.
tPLZ and tPHZ are the same as tDIS.
tPZL and tPZH are the same as tEN.
tPLH and tPHL are the same as tPD.
12-0208
10
www.pericom.com P-0.107/18/12
PI74AVC164245
16-Bit 1.2-2.5V to 3.3V Level Shifting Transceiver with 3-State Outputs
Parameter Measurement Information, VCCO = 2.5V ± 0.2V
VIN
From Output
Under Test
2 × VCC
500Ω
Open
Test
S1
tPD
tPLZ/ tPZL
tPHZ/ tPZH
Open
2 x VCCO
GND
CL = 30pF
500Ω
Output
Control
(low-level
enabling)
VCCI/2
VCCI/2
tPHL
tPLH
Output
0V
tPZH
VOH
Output
Waveform 2
S1 at GND
VCCO/2
VOL
VCCO/2
VCCI
VCCI/2
VCCI/2
Output tPZL
Waveform 1
S1 at 6V
VCCI
Input
GND
tPLZ
VCCO/2
tPHZ
VCCO/2
0V
VCCO
VOL+0.2V
VOL
VOH
VOH –0.2V
0V
Voltage Waveforms
Enable and Disable Times
Figure 3. Load Circuit and Voltage Waveforms
Notes:
CL includes probe and jig capacitance.
Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control.
All input pulses are supplied by generators having the following characteristics: PRR ≤10Mz, ZO = 50Ω, tR ≤ 2.5ns, tF ≤ 2.5ns.
The outputs are measured one at a time with one transition per measurement.
tPLZ and tPHZ are the same as tDIS.
tPZL and tPZH are the same as tEN.
tPLH and tPHL are the same as tPD.
12-0208
11
www.pericom.com P-0.107/18/12
PI74AVC164245
16-Bit 1.2-2.5V to 3.3V Level Shifting Transceiver with 3-State Outputs
Parameter Measurement Information, VCCO = 3.3V ± 0.3V
VIN
From Output
Under Test
500Ω
S1
6V
Open
Test
S1
tPD
tPLZ/ tPZL
tPHZ/ tPZH
Open
2 x VCCO
GND
CL = 30pF
500Ω
Output
Control
(low-level
enabling)
VCCI/2
VCCI/2
tPHL
tPLH
Output
VCCO/2
VCCI
VCCI/2
Output tPZL
Waveform 1
S1 2 x VCCO
VCCA
Input
0V
tPZH
VOH
Output
Waveform 2
S1 at GND
VCCO/2
VOL
GND
VCCI/2
tPLZ
VCCO/2
tPHZ
VCCO/2
0V
VCCI
VOL+0.3V
VOL
VOH
VOH –0.3V
0V
Voltage Waveforms
Enable and Disable Times
Figure 4. Load Circuit and Voltage Waveforms
Notes:
CL includes probe and jig capacitance.
Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control.
All input pulses are supplied by generators having the following characteristics: PRR ≤10Mz, ZO = 50Ω, tR ≤ 2.5ns, tF ≤ 2.5ns.
The outputs are measured one at a time with one transition per measurement.
tPLZ and tPHZ are the same as tDIS.
tPZL and tPZH are the same as tEN.
tPLH and tPHL are the same as tPD.
12-0208
12
www.pericom.com P-0.107/18/12
PI74AVC164245
16-Bit 1.2-2.5V to 3.3V Level Shifting Transceiver with 3-State Outputs
Packaging Mechanical: 48-Pin TSSOP (A)
DOCUMENT CONTROL NO.
PD - 1501
48
REVISION: G
DATE: 03/09/05
.236
.244
6.0
6.2
See Note 4
1
.488 12.4
.496 12.6
See Note 3
.047
1.20 Max
SEATING PLANE
1
.004 0.09
.008 0.20
X.XX
X.XX
DENOTES DIMENSIONS
IN MILLIMETERS
.0197
BSC
0.50
.002
.006
0.05
0.15
.007
.010
0.17
0.27
Note:
1. Controlling dimensions in millimeters.
2. Ref: JEDEC MO-153F/ED
3. Dimension does not include mold flash, protrusions or gate burrs. Mold flash, protrusions and gate burrs shall not exceed 0.15mm per side.
4. Dimension does not include interlead flash or protrusion. Interlead flash or protrusion
shall not exceed 0.25mm per side.
0.45 .018
0.75 .030
.319
BSC
8.1
Pericom Semiconductor Corporation
3545 N. 1st Street, San Jose, CA 95134
1-800-435-2335 • www.pericom.com
DESCRIPTION: 48-Pin 240-Mil Wide TSSOP
PACKAGE CODE: A
Pericom Semiconductor Corporation • 1-800-435-2336
12-0208
13
www.pericom.com P-0.107/18/12
PI74AVC164245
16-Bit 1.2-2.5V to 3.3V Level Shifting Transceiver with 3-State Outputs
Packaging Mechanical: 48-Pin TSSOP (V)
DATE: 09/27/11
Notes:
1. All dimensions are in inches
2. JEDEC outline : MO-118 AA.
3. Dimensions E and D do not include mold protrusion.
DESCRIPTION: 48-Pin, 300-Mil Wide, SSOP
PACKAGE CODE: V (V48)
DOCUMENT CONTROL #: PD-1401
REVISION:F
11-0197
12-0208
14
www.pericom.com P-0.107/18/12
PI74AVC164245
16-Bit 1.2-2.5V to 3.3V Level Shifting Transceiver with 3-State Outputs
Packaging Mechanical: 48-Pin TSSOP (K)
1
DATE: 08/29/08
DESCRIPTION: 48-Pin, 173mil wide TVSOP (TSSOP)
PACKAGE CODE:
K48
DOCUMENT CONTROL #: PD-1324
REVISION: D
08-0442
Ordering Information
Ordering Code
Package Code Speed Grade
Package Description
PI74AVC164245AE
A
Blank
Pb-free & Green, 48-pin 240-mil wide plastic TSSOP
PI74AVC164245KE
K
Blank
Pb-free & Green, 48-pin 173-mil wide plastic TVSOP
PI74AVC164245AAE
A
A
Pb-free & Green, 48-pin 240-mil wide plastic TSSOP
PI74AVC164245AVE
V
A
Pb-free & Green, 48-pin 300-mil wide plastic SSOP
PI74AVC164245AKE
K
A
Pb-free & Green, 48-pin 173-mil wide plastic TVSOP
Notes:
1. Thermal characteristics can be found on the company web site at www.pericom.com/packaging/
2.E = Pb-free and Green
3.X Suffix =Tape/Reel
12-0208
15
www.pericom.com P-0.107/18/12