RS2135 High Precision CC/CV Primary-Side PWM Power Switch DESCRIPTION RS2135 is a high performance offline PWM Power switch for low power AC/DC charger and adaptor applications. It operates in primary-side sensing and regulation. Consequently, opto-coupler and 431 could be eliminated. Proprietary Constant Voltage (CV) and Constant Current (CC) control is integrated as shown in the Figure 1. In CC control, the current and output power setting can be adjusted externally by the sense resistor RS at CS pin. In CV control, multi-mode operations are utilized to achieve high performance and high efficiency. In addition, good load regulation is achieved by the built-in cable drop compensation. Device operates in PFM in CC mode as well at large load condition and it operates in PWM with frequency reduction at light/medium load. RS2135 offers power on soft start control and protection coverage with auto-recovery features including Cycle-by-Cycle current limiting, VDD OVP, VDD clamp and UVLO. Excellent EMI performance is achieved with Frequency Jiggling. FEATURES • 5% constant voltage regulation, 5% constant current regulation at universal AC input • Primary-side sensing and regulation without 431 and opto-coupler • Power on soft-start • Built-in Leading Edge Blanking (LEB) • Cycle-by-Cycle current limiting • VDD under voltage lockout with hysteresis (UVLO) • Programmable CV and CC regulation • Adjustable constant current and output power setting • Built-in secondary constant current control with primary side feedback • Built-in adaptive current peak regulation • Built-in primary winding inductance compensation • Program cable drop compensation • VDD OVP and VDD clamp • Available in an SOP-8 package • RoHS compliant and 100% Lead (Pb)-Free and Green (Halogen Free with Commercial Standard) APPLICATIONS • • • • • Cell phone charger Digital cameras charger Small power adaptor Auxiliary power for PC, TV etc. Linear regulator/RCC replacement Figure 1. Typical CC/CV Curve Tel: 886-66296288‧Fax: 886-29174598‧ http://www.princeton.com.tw‧2F, No. 233-1, Baociao Rd., Sindian Dist., New Taipei City 23145, Taiwan RS2135 BLOCK DIAGRAM APPLICATION CIRCUIT V1.0 2 March 2013 RS2135 ORDER INFORMATION Device RS2135 Y Z Device Code Y is package & Pin Assignments designator: S: SOP-8 Z is Lead Free designator: P: Commercial Standard, Lead (Pb) Free and Phosphorous (P) Free Package G: Green (Halogen Free with Commercial Standard) PIN CONFIGURATION SOP-8 PIN DESCRIPTION Pin Name VDD COMP INV CS DRAIN GND V1.0 Description Power supply Loop compensation for CV stability The voltage feedback from auxiliary winding. Connected to resistor divider from auxiliary winding reflecting output voltage. PWM duty cycle is determined by EA output and current sense signal at pin 4. Current sense input HV MOSFET drain pin. The Drain pin is connected to the primary lead of the transformer. Ground 3 Pin No. 1 2 3 4 5, 6 7, 8 March 2013 RS2135 FUNCTION DESCRIPTION RS2135 is a cost effective PWM power switch optimized for off-line low power AC/DC applications including battery chargers and adaptors. It operates in primary side sensing and regulation, thus opto-coupler and 431 are not required. Proprietary built-in CV and CC control can achieve high precision CC/CV control meeting most adaptor and charger application requirements. STARTUP CURRENT AND START UP CONTROL Startup current of RS2135 is designed to be very low so that VDD could be charged up above UVLO threshold and starts up quickly. A large value startup resistor can therefore be used to minimize the power loss in application. OPERATING CURRENT The Operating current of RS2135 is as low as 2.5mA. Good efficiency is achieved with the low operating current together with multi-mode control features. SOFT START RS2135 features an internal soft start to minimize the component electrical over-stress during power on startup. As soon as VDD reaches UVLO (OFF), the control algorithm will ramp peak current voltage threshold gradually from nearly zero to normal setting of 0.90V. Every restart is a soft start. CC/CV OPERATION RS2135 is designed to produce good CC/CV control characteristic as shown in the Figure 1. In charger applications, a discharged battery charging starts in the CC portion of the curve until it is nearly full charged and smoothly switches to operate in CV portion of the curve. In an AC/DC adapter, the normal operation occurs only on the CV portion of the curve. The CC portion provides output current limiting. In CV operation, the output voltage is regulated through the primary side control. In CC operation mode, RS2135 will regulate the output current constant regardless of the output voltage drop. PRINCIPLE OF OPERATION To support RS2135 proprietary CC/CV control, system needs to be designed in DCM mode for flyback system (Refer to Application Circuit). In the DCM flyback converter, the output voltage can be sensed via the auxiliary winding. During MOSFET turn-on time, the load current is supplied from the output filter capacitor CO. The current in the primary winding ramps up. When MOSFET turns off, the primary current transfers to the secondary at the amplitude of IS = NP × IP NS The auxiliary voltage reflects the output voltage as shown in Figure 2 and it is given by V AUX = N AUX × (VO + ΔV ) NS Where ΔV indicates the drop voltage of the output Diode. V1.0 4 March 2013 RS2135 Figure 2. Auxiliary voltage waveform Via a resistor divider connected between the auxiliary winding and INV (pin 3), the auxiliary voltage is sampled at the end of the demagnetization and it is hold until the next sampling. The sampled voltage is compared with VREF (2.0V) and the error is amplified. The error amplifier output COMP reflects the load condition and controls the PWM switching frequency to regulate the output voltage, thus constant output voltage can be achieved. When sampled voltage is below VREF and the error amplifier output COMP reaches its maximum, the switching frequency is controlled by the sampled voltage thus the output voltage to regulate the output current, thus the constant output current can be achieved. ADJUSTABLE CC POINT AND OUTPUT POWER In RS2135, the CC point and maximum output power can be externally adjusted by external current sense resistor RS at CS pin as illustrated in Application Circuit. The output power is adjusted through CC point change. The larger RS, the smaller CC point is, and the smaller output power becomes, and vice versa as shown in Figure 3. Figure 3. Adjustable output power by changing RS V1.0 5 March 2013 RS2135 OPERATION SWITCHING FREQUENCY The switching frequency of RS2135 is adaptively controlled according to the load conditions and the operation modes. No external frequency setting components are required. The operation switching frequency at maximum output power is set to 60KHz internally. For flyback operating in DCM, The maximum output power is given by Po MAX = 1 × LP × FSW × I P 2 2 Where LP indicate the inductance of primary winding and IP is the peak current of primary winding. Refer to the equation 3, the change of the primary winding inductance results in the change of the maximum output power and the constant output current in CC mode. To compensate the change from variations of primary winding inductance, the switching frequency is locked by an internal loop such that the switching frequency is FSW = 1 2TDEMAG Since TDEMAG is inversely proportional to the inductance, as a result, the product LP and FSW is constant, thus the maximum output power and constant current in CC mode will not change as primary winding inductance changes. Up to ±10% variation of the primary winding inductance can be compensated. FREQUENCY JIGGLING FOR EMI IMPROVEMENT The Frequency Jiggling (switching frequency modulation) is implemented in RS2135. The oscillation frequency is modulated so that the tone energy is spread out. The spread spectrum minimizes the conduction band EMI and therefore eases the system design. CURRENT SENSING AND LEADING EDGE BLANKING Cycle-by-Cycle current limiting is offered in RS2135 current mode PWM control. The switch current is detected by a sense resistor into the CS pin. An internal leading edge blanking circuit chops off the sensed voltage spike at initial internal power MOSFET on state so that the external RC filtering on sense input is no longer needed. The PWM duty cycle is determined by the current sense input voltage and the EA output voltage. GATE DRIVE The internal power MOSFET in RS2135 is driven by a dedicated gate driver for power switch control. Too weak the gate drive strength results in higher conduction and switch loss of MOSFET while too strong gate drive compromises EMI. A good tradeoff is achieved through the built-in totem pole gate design with right output strength control. PROGRAMMABLE CABLE DROP COMPENSATION In RS2135, cable drop compensation is implemented to achieve good load regulation. An offset voltage is generated at INV by an internal current flowing into the resister divider. The current is inversely proportional to the voltage across pin COMP, as a result, it is inversely proportional to the output load current, thus the drop due to the cable loss can be compensated. As the load current decreases from full-load to no-load, the offset voltage at INV will increase. It can also be programmed by adjusting the resistance of the divider to compensate the drop for various cable lines used. V1.0 6 March 2013 RS2135 PROTECTION CONTROL Good power supply system reliability is achieved with its rich protection features including Cycle-by-Cycle current limiting (OCP), VDD clamp, Power on Soft Start, and Under Voltage Lockout on VDD(UVLO). VDD is supplied by transformer auxiliary winding output. The output of RS2135 is shut down when VDD drops below UVLO(ON) limit and Switcher enters power on start-up sequence thereafter. V1.0 7 March 2013 RS2135 ABSOLUTE MAXIMUM RATINGS Parameter Drain voltage (off state) VDD voltage VDD Zener clamp continuous current COMP voltage CS input voltage INV input voltage Junction temperature Operating temperature range Storage temperature range Lead temperature (soldering, 10secs) Symbol ‐ ‐ ‐ ‐ ‐ ‐ TJ TOPR TSTG TLEAD Ratings ‐0.3V to Bvdss ‐0.3 to VDD_Clamp 10 ‐0.3 to 7 ‐0.3 to 7 ‐0.3 to 7 ‐20 to 150 ‐20 to +85 ‐40 to +150 260 Unit V V mA V V V ℃ ℃ ℃ ℃ Note: Stress beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. Exposure to absolute maximum‐ rated conditions for extended periods may affect device reliability. OUTPUT POWER TABLE Part No. RS2135S Package SOP-8 230VAC ±15% 6W 85 to 265VAC 5W ELECTRICAL CHARACTERISTICS (VDD=16V, TA=25℃, unless otherwise specified) Parameter Symbol Supply Voltage (VDD) Section Standby current IDD ST Operation current VDD under voltage lockout enter VDD under voltage lockout exit Over voltage protection voltage Maximum VDD operation voltage Current Sense Input Section LEB time Over current threshold OCP Propagation delay Input impedance Soft start time CV Section System nominal switch frequency Frequency jitter range Error Amplifier Section Reference voltage for EA DC gain of the EA Max. cable compensation current Power MOSFET Section MOSFET drain‐source breakdown voltage Static drain to source on resistance V1.0 Test Condition Min. Typ. Max. Unit VDD=13V Operation supply current INV=2V,CS=0V, VDD=20V VDD falling VDD rising Ramp up VDD until gate clock is off IDD=10mA - 5 20 μA - 2.5 3.5 mA 13.5 7.5 14.5 8.5 16.0 10 V V 27.5 29.5 31.5 V 30.5 32.5 34.5 V 870 - 540 900 150 50 10 930 - ns mV ns KΩ ms - 60 14 ±4 - KHZ KHZ % 1.97 - 2 60 42 2.03 - V dB μA BVdss - 650 - V RDS(on) - 12 15 Ω IDD_OP UVLO(ON) UVLO(OFF) OVP VDD Clamp TLEB Vth_oc Td_oc ZSENSE IN Tss Freq_Nom Freq_startup Δf/Freq INV=0V, Comp=5V VREF_EA Gdc I_COMP_MAX INV=2V, COMP=0V 8 March 2013 RS2135 PACKAGE INFORMATION 8-PIN, SOP Notes: 1. Refer to JEDEC MS-012 AA. 2. All dimensions are in millimeter. V1.0 9 March 2013 RS2135 IMPORTANT NOTICE Princeton Technology Corporation (PTC) reserves the right to make corrections, modifications, enhancements, improvements, and other changes to its products and to discontinue any product without notice at any time. PTC cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a PTC product. No circuit patent licenses are implied. Princeton Technology Corp. 2F, 233-1, Baociao Road, Sindian Dist., New Taipei City 23145, Taiwan Tel: 886-2-66296288 Fax: 886-2-29174598 http://www.princeton.com.tw V1.0 10 March 2013