PT5101 4CH DSC Motor Driver DESCRIPTION FEATURES The PT5101 is a monolithic 4-Channel CMOS H-bridge motor driver. It can drive one stepper motor, two DCM and two coils. There also are several other flexible system solutions left to be utilized. The current consumption can be hold at quite low level during standby or operation. And the active power supply voltage range is from 2.7~5.5V. So the device is ideal for portable and battery powered applications. • Independent 4channel H-bridge, 3 full-swing drivers and 1 constant-current driver, all of those drivers with brake function. • Versatile and flexible control mode - DC/stepper motor alternative, Full-swing/ Constant-Voltage/ Constant-Current selected • Special Exclusive Control mode optional • Constant-Voltage set by DAC: 1.8V~4.8V 0.2V/Bit Accuracy ± 5% • Constant current set by DAC: 150mV~300mV 10mV/Bit Accuracy±5% • Under voltage lockout circuit - Shut down the internal circuit at VCC=1.8V (Typ.) • Thermal shut down circuit - Shut down the internal circuit at 150℃ Hysteresis 30℃ • Available in small package HLA24 (3mm × 3mm) The PT5101 is available in HLA24 (3mm × 3mm) package. Performance is specified for -20℃ to +85℃ temperature range. APPLICATIONS • DSC BLOCK DIAGRAM Vcc Power supply VM Power supply VCC BIAS Low voltage detection TSD VREF (1.25V), POR H bridge C.V./Full ON IN123 Serial Interface Logic 12 SDA CS RESET RESET Serial Interface 4Bit DAC VM12 VC12 H bridge C.V./Full ON OUT2A OUT2B PGND12 PI1 PI2 MCU OUT1B Logic 3 Serial Interface Level Shift & Pre Driver PI3 Serial Interface H bridge C.V./Full ON 4Bit DAC OUT3A OUT3B ZOOM/IRIS (DCM/COIL) PGND3 VC3 ZOOM/IRIS (DCM/COIL) VM34 IN4A Control signal IN4B Logic 4 Serial Interface Serial Interface Level Shift & Pre Driver 4Bit DAC ZOOM/IRIS(STM-2) SCL Serial Interface Serial control signal Level Shift & Pre Driver OUT1A AutoFocus(STM-1) Control signal Exclusive 1 VC4 H bridge 4A:C.V./C.C./ Full ON 4B:C.C. Exclusive 2 OUT4A OUT4B SHUTTER (COIL) RNF4 Notes: 1. FS=Full-swing 2. CV= Constant-Voltage 3. CC=Constant-Current Tel: 886-66296288‧Fax: 886-29174598‧ http://www.princeton.com.tw‧2F, 233-1, Baociao Road, Sindian, Taipei 23145, Taiwan PT5101 ORDER INFORMATION Valid Part Number PT5101 Package Type 24 pins, HLA Top Code PT5101 PIN CONFIGURATION Note: The Exposed PAD must be connect to GND PIN DESCRIPTION Pin Name RESET CS SDA SCL OUT2B OUT3A PGND3 PI3 PGND12 OUT2A OUT3B VM34 VM12 OUT1B OUT4A RNF4 VCC PI1 OUT1A OUT4B IN123 IN4A IN4B PI2 PGND12 V1.0 I/O I I I I O O GND OUT GND O O Power Supply Power Supply O O I/O Power Supply OUT O O I I I OUT GND Description Logic reset Serial data latch control Serial data input Serial clock input CH2 output B CH3 output A CH3 Power GND PI3 Output CH12 Power GND CH2 output A CH3 output B CH3/4 Power supply CH1/2 Power supply CH1 output B CH4 output A CH4 current sense input or Power GND Small signal power supply PI1 Output CH1 output A CH4 output B CH1/CH2/CH3 Input Control Pin CH4 Input Control Pin CH4 Input Control Pin PI2 Output CH1/2 Power GND and pre driver GND 2 Pin No. A1 A2 A3 A4 A5 B1 B2 B3 B4 B5 C1 C2 C4 C5 D1 D2 D3 D4 D5 E1 E2 E3 E4 E5 Bottom March 2010