Technical Guidance

TX7-503CM-SQ-CoSa
Analogue Temperature Compensated Xtal Oscillator
COSPAS SARSAT compliant CMOS TCXO
Application:
Emergency beacon Class 1 & 2
Standard frequencies
10.000 MHz, 12.678303 MHz
12.800 MHz, 16.384, 20.000 MHz
Frequency stability:
vs. temperature
reference to (FMAX+FMIN)/2
vs. supply voltage
vs. load
vs. aging
Frequency tolerance @ +25 °C
Frequency tolerance after reflow
Allan variance (ADEV)
≤ ±0.2 ppm
≤ ±0.2 ppm
≤ ±0.1 ppm
≤ ±0.1 ppm
≤ ±1.0 ppm
≤ ±3.0 ppm
≤ ±0.5 ppm
≤ ±0.5 ppm
0.1 ppb (1x10-10 )
-20 ~ +55 °C
-40 ~ +55 °C
±5 %
±5 %
1st year
10 years
Class 2 beacon
Class 2 beacon
@  = 0.1 ~ 1.0 sec
Medium-term stability:
Mean slope F/dt after 15 min power-up:
steady state
during temperature ramp
Residual F (r.m.s.) from slope
IAW C/S T.007 and C/S IP TCXO
≤ ±0.7 ppb/min.
≤ ±1.7 ppb/min.
≤ 2.0 ppb
T = const.
T/dt = ± 5 °C/hour
over 18 points
Supply voltage
Supply current
Output signal
Output load
Symmetry (Duty)
+3.3 V
4 mA
CMOS
15 pF
45 % ~ 55 %
±5 %
Max.
VOH > 0.9Vdc
±5 %
@ ½ Vdc
<-90 dBc/Hz
<-115 dBc/Hz
<-130 dBc/Hz
<-140 dBc/Hz
<-145 dBc/Hz
@
@
@
@
@
-20 ~ +55 °C
-40 ~ +55 °C
-55 ~ +125 °C
Class 2 beacon
Class 1 beacon
Phase noise @ 12.678303 MHz
Operating temperature range
Storage temperature range
Pin function
#1
#4
#5
#8
VOL < 0.1Vdc
10 Hz
100 Hz
1 kHz
10 kHz
100 kHz
Solder pattern
Do not connect
GND
OUTPUT
Vdc
Do not connect: #2, #3, #6 &, #7
IR reflow soldering temperature
2011/65/EU RoHS compliant
QuartzCom AG
Bischmattstrasse 11
CH 2544 Bettlach
Switzerland
Fax
Tel
E-Mail
+41 32 644 24 05
+41 32 644 24 00
[email protected]
www.quartzcom.com
Page 1 of 2
24 Jan. 14
TX7-503CM-SQ-CoSa
Analogue Temperature Compensated Xtal Oscillator
COSPAS SARSAT compliant CMOS TCXO
Application:
Emergency beacon Class 1 & 2
Medium term stability
Frequency stability measurement procedure according the COSPAS-SARSAT T.001
Note #1:
Tmin
TON
Tmeas
= -20 °C (Class 2 beacon)
= beacon turn-ON time after 2 hours “cold soak”
= start time of frequency stability measurement (TON + 15 min)
Note: #2
The 2h and 1h warm-up and stabilisation times are for type approval test of complete beacon.
For testing of TCXO these times may be shortened accordingly.
Environmental
Reference STD.
Test condition
Vibration
sinusoidal
IEC 60028-2-6
IEC 60679-15.6.7
Shock
IEC 60028-2-27
IEC 60679-15.6.8
Solderability
IEC 60028-2-20
IEC 60028-2-58
IEC 60679-5.6.3
Test Fc, 30 min per axis
10 Hz – 55 Hz 0.75mm, 55 Hz – 2 kHz 10
g
Test Ea, 3 x per axes 100 g,
6 ms half-sine pulse
Test Ta (235 ±2) °C Method 1
Test Tb Method 1A, 5s
2011/65/EU RoHS compliant
QuartzCom AG
Bischmattstrasse 11
CH 2544 Bettlach
Switzerland
Fax
Tel
E-Mail
+41 32 644 24 05
+41 32 644 24 00
[email protected]
www.quartzcom.com
Page 2 of 2
24 Jan. 14