PFC Series

PFC Series
Thick Film Power SMD Resistors
•
•
•
•
•
•
•
D-PAK Foot Pattern
Very Low Profile
Resistances from 0.1 Ohm to 51kOhms
Power Rating to 25 Watts
Resistance Tolerances to ±1%
TCR to ±100ppm/°C
Isolated Back Plate
SPECIFICATIONS
Type
PFC10
Power Rating with heatsink
25W
( 2.5W on Simple Foot Print )
Short Time Overload
35 W
Thermal Resistance Rthj-c
3.6 K/W
Resistance Range
0.1 - 51K Ohms E24+
(includes 2.5, 4.0, 5.0, 8.0, and 16)
Tolerances (others upon request)
1% / 5%
Temperature Coefficient
100 ppm/K
Operating Temperature
-55°C to 155°C
Max Operating Voltage
P*R
Capacitance
1.44 pF
Inductance
8.38 nH
Withstanding Voltage
1500 VAC
Insulation Resistance
Over 1,000 Megohm
Resistor Material
Thick Film
Test Conditions
Results
Load Life
±1%
90 min ON, 30 min OFF, 1000 hrs @ 25C
Humidity
±1%
90-95% RH, 0.1W, 1000 hrs @ 40C
Temperature Cycle
±0.25%
-55C for 30 min, +155C for 30 min, 5 cycles
Solder Heat
±0.1%
350C ±5C for 3 seconds
Lead Solderability
Vibration
Over 95% of surface
±0.25%
230 ±5C for 3 seconds
IEC60068-2-6
Ordering Information
Part Description: Part Type - Resistance - Tolerance
PFC10 10 Ohms 1%
Note: PFC10 can operate 35W rating with back solder pad temperature of 25°C
Riedon Inc.
300 Cypress Avenue
Alhambra CA 91801
www.riedon.com
(626) 284-9901
(626) 284-1704
PFC Series
Thick Film Power SMD Resistors
DIMENSIONS
Solder Pad Layout
H
C
A
G
B
I
F
L
E
K
D
J
Note: Back solder pad is isolated from both pins.
Dimension
mm
tol.
(±mm)
inches
tol.
(±inches)
A
8.2
0.2
0.323
0.008
B
12.0
0.2
0.472
0.008
C
1.0
0.05
0.039
0.002
D
5.08
0.1
0.200
0.004
E
0.75
0.05
0.030
0.002
F
1.8
0.05
0.070
0.002
G
8.5
-
0.335
-
H
8.8
-
0.346
-
I
14.1
-
0.555
-
J
5.08
-
0.200
-
K
2.0
-
0.079
-
L
3.8
-
0.150
-
CHIP CONSTRUCTION (EXPLODED VIEW)
Riedon Inc.
300 Cypress Avenue
Alhambra CA 91801
www.riedon.com
(626) 284-9901
(626) 284-1704
PFC Series
Thick Film Power SMD Resistors
MOUNTING
Derating
Power Derating Curve
Power Rating Notes °C
Power ( % )
The PFC Series Resistors must be attached to a suitable heatsink. The maximum internal resistor temperature is 155°C.
To specify an appropriate heatsink use the following formula :
RHH =
Where:
°C
Heatsink Temperature (°C)
TMAX - (P * RHR) - TA
P
RθH = Thermal Resistance of Heatsink ( K/W )
RθR = Thermal Resistance of Resistor ( K/W )
TMAX = Maximum Temperature of Resistor
TA = Ambient Temperature of Heatsink ( °C )
P = Power Through Resistor ( W )
Copper Insert
Copper insert improves thermal conductivity to heatsink. Power ratings
of 35W can be achieved through active cooling of the heatsink. For
more general information on heatsinking please see our training module on heatsinking by clicking here.
Via-Holes
Plastic Tape Specifications
Standard Package contains 500 pcs/reel, diameter 254mm reel in paper box.
Digikey Package contains 500 pcs/reel, diameter 254mm reel in paper box.
Riedon Inc.
300 Cypress Avenue
Alhambra CA 91801
www.riedon.com
(626) 284-9901
(626) 284-1704