Lead Free POWER SOLUTION - DBL TO126 20W HIGH POWER RESISTORS RNP-10S Features and Applications Small 20Watt high power resistor in TO-126 package with 5.9 C/W heat resistance from hot spot to flange. Non-Inductive, fit for high speed SW power sources, high precision CRT and high-speed pulse handling circuits. Thin style in small package suits high density installation of electronic instruments. Superior vibration durability with heat sink mounting. Complete thermal flow design available. Color video amplifier of CRTs, emitter resistors of power SW circuits, snubber circuits, VHF amplifiers, load resistor of pulse generators. dia.3.1 3.1 101 CF 4X Between flange and resistor are insulated. 15.2 8.5 12.0 3.8 Dimensions Leads, Tin plated Cu Molding, epoxy Conductor, Cu Resistor, NiCr Substrate, Alumina Flange, Ni plated Cu 1.9 0.5 15.0 0.6 5.08 12.0 1.4 (mm) Specifications and Performances Items Rating Power Rating Power Hear resistance Resistance Range Nominal Resistance TCR Tolerance Operation Temp. Range Withstanding Voltage Load Life Humidity Soldering Heat Solder ability Insulation Resistance Vibration Specification-Performance 20 Watts 1 Watt 5.9 C/W 1.0-9.1ohm 10-220ohm E24 E24 +/-100 ppm/C(A) +/-50 ppm/C(C) +/-5%(J) +/-1%(F) -55 C to +155 C 2000 Volt DC +/-(1.0 %+0.05ohm) +/-(1.0 %+0.05ohm) +/-(1.0 %+0.05ohm) Over 3/4 of surface Over 1000 Meg ohm +/-(0.25 %) Test Conditions Flange temperature of -55 C to +25 C Free air (without heat sink). From hot spot to flange. Up to 51kohm resistance are available. Note(6) Flange temperature -55 to +155 C 60 seconds, between terminals and flange. 25C, 90 min.ON, 30min.OFF, 1000hours. 60C, 90 to 95%RH, DC0.1W, 1000hours. 350+/-5C, 3seconds, 230+/-5C, 3seconds. Between terminals and flange. DB LECTRO Inc. 3600 boul. Matte suite i Brossard Qc J4Y-2Z2 tel:(450)-444-1424 fax:(450)-444-4714 www.dblectro.com Lead Free POWER SOLUTION – DBL RNP-10S HIGH POWER RESISTORS Ordering Information Identification RNP10SC500F000 RNP10SC500FZ00 RNP10SC101F010 RNP10SC101FZ10 RNP10SA0R1J000 Type RNP10S RNP10S RNP10S RNP10S RNP10S TC C(50ppm/C) C(50ppm/C) C(50ppm/C) C(50ppm/C) A(100ppm/C) Derating Curve Resistance 50ohm 50ohm 100ohm 100ohm 0.1ohm Tolerance F(1%) F(1%) F(1%) F(1%) J(5%) Code 000 Z00 (Z: Lead-free) 010 Z10(Z: Lead-free) 000 Temperature Rise at flange Temperature(C) 140 Rating Power(W), with 2.8K/W heat sink. 120 10 100 +25C 8 80 6 60 4 40 2 20 +155C 0 -50 0 50 100 150 0 200 0 10 Power (W) Flange Temperature (C) Frequency Characteristics One time rectangular impulse. Impedance (ohm) 1K RNP-10S C1K0F Pulse Peak Watt (Watts) 10K RNP-10CS100F 100 10 1 RNP-10S C101F 1K RNP-10S C500F RNP-10S C100F 100 RNP-10S C5R0F 100k 1M 10M 20 100M 1G Frequency(Hz) 10G 10 1µ 10µ 100µ 1m 10m 100m Pulse Width (seconds) Notes (1) Insulating material will not be used between flange and resistors, because flange and resistor are separated by alumina substrate. (2) Using heat conduction grease on surface of tab is recommended. (3) Heat resistance between resistor and tab is 3.6K/W, heat design will be performed as resistor temperature shall be under 155 C in operation. (4) 0.1% tolerance resistors are available, please call factory. (5) For application to r-f circuit, RMP10S (smd) or lead formed RNP10S are prepared, RNP10S or RMP10S are screw mount style. When soldering mount is better, please use RMP20S. (6) At resistance from 220 to 51kohms rating power shall be restricted in 10W. 20050212 DB LECTRO Inc. 3600 boul. Matte suite i Brossard Qc J4Y-2Z2 tel:(450)-444-1424 fax:(450)-444-4714 www.dblectro.com