SS1139 Unipolar Hall-Effect Digital Switch Features and Benefits Application Examples – – – – – – – – – − − − − − − − 3.8V to 24V Operation -40°C to 150°C Superior temperature operation Bipolar technology Open-collector 50 mA output Reverse battery protection Small Size SOT89 3L Solid-state reliability Resistant to 60V supply voltage Sensitivity of temperature compensation circuitry Automotive, Consumer and Industrial Solid-state switch Brushless DC motor commutation Speed detection Linear position detection Angular position detection Proximity detection 3 pin SOT89 (suffix SP) Functional Block Diagram VDD Voltage Regulator Output Amp Hall Plate GND 1 V3.10 Nov 1, 2013 SS1139 Unipolar Hall-Effect Digital Switch General Description temperature and supply voltage changes. Internal compensation characteristic makes the sensitivity increase slightly with temperature increasing, so that this IC is Particularly suitable to be used with the commonly low-cost magnets. If a magnetic flux density larger than threshold Bop, Output is turned on (low). When a magnetic flux density reversal falls below Brp, Output will be turned off (high). The SS1139 is a unipolar Hall-effect sensor IC fabricated from bipolar technology. The device integrates a voltage regulator, reverse battery protection diode, Hall sensor with dynamic offset cancellation system, temperature compensation circuitry, small signal amplifier, Schmitt trigger and an open-collector output to sink up to 50 mA. With suitable output pull up, they can be used with bipolar or CMOS logic circuits. Thanks to its wide operating voltage range, extended choice of temperature range and high reliability, it is quite suitable for use in automotive, industrial and consumer applications. These Hall-effect switches are monolithic integrated circuits with tighter magnetic specifications, designed to operate continuously over extended temperatures to +150°C,and are more stable with both Glossary of Terms MilliTesla (mT), Gauss Units of magnetic flux density: 1mT = 10 Gauss RoHS Restriction of Hazardous Substances Operating Point (BOP) Magnetic flux density applied on the branded side of the package which turns the output driver ON (VOUT = VDSon) Release Point (BRP) Magnetic flux density applied on the branded side of the package which turns the output driver OFF (VOUT = high) 2 V3.10 Nov 1, 2013 SS1139 Unipolar Hall-Effect Digital Switch Pin Definitions and Descriptions SOT Pin № Name Type 1 VDD Supply Supply Voltage pin 2 GND Ground Ground pin 3 OUT Output Open Collector Output pin Function Absolute Maximum Ratings Symbol Parameter Value Units Supply Voltage VDD 60 V Reverse Voltage VDD -24 V Output Voltage VOUT 30 V Output Current IOUT 50 mA Magnetic Flux Density B No limit Operating Temperature Range TA -40 to +150 °C Storage Temperature Range TS -65 to 170 °C Maximum Junction Temperature TJ +150 °C Lead Temperature(Solding, TL +250 °C PD 450 mW Value Units 5 sec) Package Power Dissipation Operating Temperature Range Symbol Temperature Suffix “E” TA -40 to 85 °C Temperature Suffix “K” TA -40 to 125 °C Temperature Suffix “L” TA -40 to 150 °C Exceeding the absolute maximum ratings may cause permanent damage. Exposure to absolute-maximum- rated conditions for extended periods may affect device reliability . 3 V3.10 Nov 1, 2013 SS1139 Unipolar Hall-Effect Digital Switch General Electrical Specifications DC Operating Parameters TA = 25°C, VDD= 3.8V to 24V (unless otherwise specified) Parameter Supply Voltage Supply Current Output Saturation Voltage Output Current Output Leakage Current Symbol Test Conditions Min VDD IDD VDSon ION IOFF Operating VDD=12V IOUT = 20mA, B > BOP B > BOP B < BRP VCC=12V, RL = 1.1KΩ, CL = 20pF VCC=12V, RL = 1.1KΩ, C L = 20pF 3.8 Output Rise Time tr Output Fall Time tf Typ Max Units 0.1 24 10 0.6 10 10 V mA V mA µA 0.2 1.5 µs 0.5 1.0 µs 5 0.45 Magnetic Specifications Package SP Parameter Operating Point Release Point Hysteresis Symbol BOP BRP BHYST Test Conditions Min Ta=25°C,Vdd=12V DC 75 25 Typ 50 Max Units 120 80 G G G Output Behavior versus Magnetic Pole DC Operating Parameters TA = -40°C to 150°C, VDD = 3.8V to 24V (unless otherwise specified) Test Conditions (SP) OUT B < BRP B > BOP High Low 4 V3.10 Nov 1, 2013 SS1139 Unipolar Hall-Effect Digital Switch Performance Characteristics Magnetic Switch Range versus Temperature 70 Bop 60 50 Brp 40 30 Bhys 20 10 0 -40 25 85 125 Temperature(℃) Magnetic Switch Range versus Temperature 140 Flux Density(Gauss) Flux Density(Gauss) 80 150 120 Bop 100 Brp 80 60 Bhys 40 20 0 -40 25 85 125 Temperature(℃) 150 SS1139 Application Information 5 V3.10 Nov 1, 2013 SS1139 Unipolar Hall-Effect Digital Switch Package SP, 3-Pin SOT-89: Ordering Information Part No. Pb-free Temperature Code Package Code Packing SS1139ESPT YES -40°C to 85°C SOT-89 7-in. reel, 3000 pieces/reel SS1139KSPT YES -40°C to 125°C SOT-89 7-in. reel, 3000 pieces/reel SS1139LSPT YES -40°C to 150°C SOT-89 7-in. reel, 3000 pieces/reel 6 V3.10 Nov 1, 2013