FDC15 SERIES 15 WATTS DC-DC CONVERTER FEATURES • 15 WATTS OUTPUT POWER • OUTPUT CURRENT UP TO 3A • STANDARD 2.00 X 1.60 X 0.40 INCH PACKAGE • HIGH EFFICIENCY UP TO 82% • 4:1 WIDE INPUT VOLTAGE RANGE • SIX-SIDED CONTINUOUS SHIELD • FIXED SWITCHING FREQUENCY • CE MARK MEETS 2006/95/EC, 2011/95/EC AND 2004/108/EC • SAFETY MEETS UL60950-1, EN60950-1 AND IEC60950-1 • ISO9001 CERTIFIED MANUFACTURING FACILITIES • COMPLIANT TO RoHS EU DIRECTIVE 2011/65/EU DESCRIPTION The FDC15 series offer 15 watts of output power from a 2.00 x 1.60 x 0.40 inch package. The FDC15 series have 4:1 wide input voltage of 9~36VDC and 18~75VDC. The FDC15 features 1600VDC of isolation, short-circuit and over-voltage protection. APPLICATIONS Wireless Network Telecom/Datacom Industry Control System Measurement Equipment Semiconductor Equipment T E C H N I C A L S P E C I F I C AT I O N All specifications are typical at nominal input, full load and 25ºC otherwise noted INPUT SPECIFICATIONS OUTPUT SPECIFICATIONS Output power 15 Watts, max. Voltage accuracy ± 1% Minimum load (Note 6) See Table Voltage adjustability Line regulation LL to HL at Full Load Single Load regulation Min. load to Full load Dual Cross regulation (Dual) Asymmetrical load 25% / 100% FL Ripple and noise 20MHz bandwidth Short circuit protection Input filter Pi type ± 0.2% ± 0.5% ± 1% ± 5% Input reflected ripple current 250µs 6.2VDC 15VDC 18VDC 150%, max. Continuous, automatics recovery 20mAp-p Nominal input and Start up time 20ms Power up constant resistive load Remote ON/OFF (Note 7) (Positive logic) DC-DC ON Open or 3.5V < Vr < 12V DC-DC OFF Short or 0V < Vr < 1.2V Input current of remote control pin Nominal input -0.5mA~+0.5mA Remote off state input current Nominal input 20mA ENVIRONMENTAL SPECIFICATIONS Operating ambient temperature Maximum case temperature Efficiency Input to Output Input(Output) to Case See table 1600VDC, min. 1minute 1600VDC, min. 1minute Thermal impedance (Note 8) -40ºC ~ +85ºC (with derating) 100ºC Storage temperature range GENERAL SPECIFICATIONS 9 ~ 36VDC 18 ~ 75VDC 50VDC 100ms, max. 100VDC 100ms, max. 24VDC input 48VDC input Input surge voltage See table Transient response recovery time 25% load step change 5VDC output Over voltage protection 12VDC output Zener diode clamp 15VDC output Over load protection % of FL at nominal input 24VDC nominal input 48VDC nominal input ± 10% ±0.02% / ºC, max. Temperature coefficient Input voltage range -55ºC ~ +125ºC Natural convection 10ºC/Watt Natural convection with heat-sink 8.24ºC/Watt Thermal shock MIL-STD-810F 9 Vibration MIL-STD-810F Isolation capacitance 300pF, max. Relative humidity Switching frequency 270kHz±10% EMC CHARACTERISTICS Isolation voltage Isolation resistance 500VDC Design meet safety standard 10 ohms, min. IEC60950-1, UL60950-1, EN60950-1 Case material Nickel-coated copper Base material Non-conductive black plastic Potting material Dimensions Epoxy (UL94-V0) 2.00 X 1.60 X 0.40 Inch (50.8 X 40.6 X 10.2 mm) Weight MTBF (Note 1) Page 1 of 3 48g (1.69oz) BELLCORE TR-NWT-000332 MIL-HDBK-217F 6 2.041 x 10 hrs 9.140 x 105 hrs EMI 5% to 95% RH EN55022 Class A, Class B ESD EN61000-4-2 Air ± 8kV Perf. Criteria B Contact ± 6kV Radiated immunity EN61000-4-3 10 V/m Perf. Criteria A Fast transient (Note 9) EN61000-4-4 ± 2kV Perf. Criteria B Surge (Note 9) EN61000-4-5 ± 1kV Perf. Criteria B Conducted immunity EN61000-4-6 10 Vr.m.s Perf. Criteria A www.pduke.com 2013/5/3 FDC15 SERIES 15 WATTS DC-DC CONVERTER (2) (3) Output Current Output Output No load Voltage Min. load Full load Ripple & Noise Input Current Model Number Input Range FDC15-24S05 FDC15-24S12 FDC15-24S15 FDC15-24D05 FDC15-24D12 FDC15-24D15 FDC15-48S05 FDC15-48S12 FDC15-48S15 FDC15-48D05 FDC15-48D12 FDC15-48D15 9 ~ 36 VDC 9 ~ 36 VDC 9 ~ 36 VDC 9 ~ 36 VDC 9 ~ 36 VDC 9 ~ 36 VDC 18 ~ 75 VDC 18 ~ 75 VDC 18 ~ 75 VDC 18 ~ 75 VDC 18 ~ 75 VDC 18 ~ 75 VDC 5 VDC 12 VDC 15 VDC ± 5 VDC ± 12 VDC ± 15 VDC 5 VDC 12 VDC 15 VDC ± 5 VDC ± 12 VDC ± 15 VDC 210mA 100mA 80mA ± 105mA ± 50mA ± 40mA 210mA 100mA 80mA ± 105mA ±50mA ± 40mA 3000mA 1250mA 1000mA ± 1500mA ± 625mA ± 500mA 3000mA 1250mA 1000mA ± 1500mA ± 625mA ± 500mA 75mVp-p 75mVp-p 75mVp-p 75mVp-p 75mVp-p 75mVp-p 75mVp-p 75mVp-p 75mVp-p 75mVp-p 75mVp-p 75mVp-p (4) Eff (%) Capacitor (5) Load max 80 82 82 80 82 82 80 82 82 80 82 82 6800µF 890µF 570µF ± 1700µF ± 300µF ± 200µF 6800µF 890µF 570µF ± 1700µF ± 300µF ± 200µF 20mA 10mA 20mA 20mA 20mA 20mA 15mA 15mA 10mA 10mA 20mA 15mA Note 1. 2. 3. 4. 5. 6. 7. 8. 9. BELLCORE TR-NWT-000332. Case 1: 50% Stress, Temperature at 40ºC. MIL-HDBK-217F Notice2 @Ta=25 ºC, Full load(Ground, Benign, controlled environment). Typical value at nominal input and full load. (20MHZ BW.) Typical value at nominal input and no load. Typical value at nominal input and full load. Test by minimum input and constant resistive load. The output requires a minimum loading on the output to maintain specified regulation. Operation under no-load condition will not damage these devices, however they may not meet all listed specification. The CTRL pin voltage is reference to -INPUT. Heat-sink is optional and P/N: 7G-0011C-F. An external input filter capacitor is required if the module has to meet EN61000-4-4, EN61000-4-5. The filter capacitor Power Mate suggest: Nippon chemi-con KY series, 220µF /100V. FDC15-48S05 Derating Curve 120 120 O U T P U T P O W E R (% ) O U T P U T P O W E R (% ) CAUTION: This power module is not internally fused. An input line fuse must always be used. 100 80 60 40 20 0 -40 -20 0 20 62.5 40 60 80 100 120 100 80 60 40 20 0 AMBIENT TEMPERATURE(℃) -40 E F F IC IE N C Y (% ) E F F IC IE N C Y (% ) 82% 80% 78% 76% 74% 72% 70% 40 44 48 52 56 60 64 -20 0 20 40 60 69.1 80 100 120 90 100 AMBIENT TEMPERATURE(℃ ) FDC15-48S05 Efficiency VS Input Voltage 36 FDC15-48S05 Derating Curve With Heatsink (Note (Note 68)) 68 72 INPUT VOLTAGE (V) 95 90 85 80 75 70 65 60 55 50 45 FDC15-48S05 Efficiency VS Output Load 10 20 30 40 50 60 70 80 OUTPUT LOAD (% of Full Load) Page 2 of 3 www.pduke.com 2013/5/3 FDC15 SERIES 15 WATTS DC-DC CONVERTER MECHANICAL DRAWING 1. All dimensions in Inch (mm) Tolerance: X.XX±0.02 (X.X±0.5) X.XXX±0.01 (X.XX±0.25) 2. Pin pitch tolerance ±0.01(0.25) 3. Pin dimension tolerance ±0.004 (0.1) PIN CONNECTION Page 3 of 3 PIN SINGLE DUAL 1 +INPUT +INPUT 2 -INPUT -INPUT 4 CTRL CTRL 5 NO PIN +OUTPUT 6 +OUTPUT COMMON 7 -OUTPUT -OUTPUT 8 TRIM TRIM EXTERNAL OUTPUT TRIMMING Output can be externally trimmed by using the method shown below. ( ) for dual output trim TRIM UP TRIM DOWN 7(7) 8(8) RU 8(8) www.pduke.com RD 6(5) 2013/5/3