ULQ Models
www.murata-ps.com
Single Output, Low-Profile, Quarter-Brick
8-25 Amp Isolated DC-DC Converters
Typical units
Features
■
Standard quarter-brick package/pinout
in through-hole or SMT version
■
Low cost; Low profile, 0.35" (8.9mm)
■
24V and 48V nominal inputs
■
Output current: 8 to 25 Amps
■
Output voltages: 1.2/1.5/1.8/2/2.5/3.3/5/12V
■
Interleaved synchronous-rectifier topology
· Ultra high efficiency
· No output reverse conduction
■
Outstanding thermal performance
■
On/off control, trim & sense functions
■
Fully isolated, 2250Vdc (BASIC)
■
Output overvoltage protection
■
Fully I/O protected; Thermal shutdown
■
UL/EN/IEC60950 safety approvals
■
Qual/HALT/EMI tested
For applications requiring improved electrical and thermal perfomance at reduced cost DATEL's
new ULQ Series "Quarter-Brick" DC-DC Converters suit perfectly. They measure just 1.45 x 2.30 x
0.35 inches (36.8 x 58.4 x 8.9mm) and fit the industry-standard footprint. You can also "pick-andplace" the ULQ-SMT version optimizing your automated SMT process.
From an 18-36V or 36-75V input, ULQ's deliver outputs of 1.2, 1.5, 1.8, or 2V fully rated at 15 or
25A, 2.5 or 3.3V at 15 or 20A, 5V at 15A and 12V at 8-10A. They
employ an interleaved, synchronous-rectifier topology that exploits 100% of their duty cycle. They
simultaneously achieve ultra-high efficiency (to 91%), tight line/load regulation (±0.125/0.25%), low
noise (25-70mVp-p), and quick step response (200µsec).
A state of the art, single-board, open-frame design with reduced component count, high
efficiency, low-on-resistance FET's, and planar magnetics embedded in heavy-copper pc boards all
contribute to impressive thermal derating.
The ULQ's feature set includes high isolation (2250Vdc), input pi filters, input undervoltage shutdown, output overvoltage protection, current limiting, short-circuit protection and thermal shutdown.
The standard footprint carries on/off control (positive or negative logic), output trim (+10/–20%) and
output sense functions.
All ULQ quarter-bricks are designed to meet the BASIC-insulation requirements of UL/EN/
IEC60950 and they will carry the CE mark. Safety certifications, EMC compliance testing and qualification testing (including HALT) are currently in progress. Contact DATEL for latest updates.
+SENSE
(7)
+VOUT
(8)
+VIN
(1)
SWITCH
CONTROL
–VOUT
(4)
–VIN
(3)
–SENSE
(5)
PWM
CONTROLLER
INPUT UNDERVOLTAGE, INPUT
OVERVOLTAGE, AND OUTPUT
OVERVOLTAGE COMPARATORS
REMOTE
ON/OFF
CONTROL*
(2)
OPTO
ISOLATION
REFERENCE &
ERROR AMP
VOUT
TRIM
(6)
* Can be ordered with positive (standard) or negative (optional) polarity.
Figure 1. Simplified Schematic
Typical topology is shown.
For full details go to
www.murata-ps.com/rohs
www.murata-ps.com/support
Typical
topology is shown
MDC_ULQ-15A.E02 Page 1 of 17
ULQ Models
Single Output, Low-Profile, Quarter-Brick
8-25 Amp Isolated DC-DC Converters
Performance Specifications and Ordering Guide ➀
ORDERING GUIDE
Output
VOUT
IOUT ➁ R/N (mVp-p) ➁
(Volts) (Amps) Typ.
Max.
Root Model ➄
ULQ-1.5/15-D48N-C
ULQ-1.5/25-D24P-C
ULQ-1.5/25-D48N-C
ULQ-1.8/15-D48N-C
ULQ-1.8/25-D24P-C
ULQ-1.8/25-D48N-C
ULQ-2/15-D48N-C
ULQ-2/25-D24P-C
ULQ-2/25-D48N-C
ULQ-2.5/15-D48N-C
ULQ-3.3/15-D48NM-C
ULQ-3.3/20-D24PM-C
ULQ-3.3/20-D48NM-C
ULQ-5/15-D24PM-C
ULQ-5/15-D48NM-C
ULQ-12/8-D24PM-C
ULQ-12/10-D48NM-C
ULQ-3.3/15-D48N-C
ULQ-3.3/20-D24P-C
ULQ-3.3/20-D48N-C
ULQ-5/15-D24P-C
ULQ-5/15-D48N-C
ULQ-12/8-D24P-C
ULQ-12/10-D48N-C
1.5
1.5
1.5
1.8
1.8
1.8
2
2
2
2.5
3.3
3.3
3.3
5
5
12
12
3.3
3.3
3.3
5
5
12
12
15
25
25
15
25
25
15
25
25
15
15
20
20
15
15
8
10
15
20
20
15
15
8
10
25
50
45
25
50
70
25
50
70
35
45
50
45
50
50
95
90
45
50
45
50
50
95
90
50
100
75
50
100
100
50
100
100
55
75
100
75
100
100
130
130
75
100
75
100
100
130
130
➀ Typical at TA = +25°C under nominal line voltage and full-load conditions. All models are
specified with an external 1µF multi-layer ceramic and 10µF capacitors across their output pins.
➁ Ripple/Noise (R/N) measured over a 20MHz bandwidth.
➂ Devices have no minimum-load requirements and will regulate under no-load conditions.
Regulation specifications describe the output voltage deviation as the line voltage or load is
varied from its nominal/midpoint value to either extreme. (Load step = 50%.)
Input
Regulation (Max.) VIN Nom. Range
IIN ➃
Line
Load ➂ (Volts) (Volts) (mA/A)
±0.125%
±0.125%
±0.125%
±0.125%
±0.125%
±0.25%
±0.125%
±0.125%
±0.25%
±0.125%
±0.125%
±0.125%
±0.125%
±0.25%
±0.1%
±0.25%
±0.25%
±0.125%
±0.125%
±0.125%
±0.25%
±0.1%
±0.25%
±0.25%
±0.25%
±0.25%
±0.25%
±0.25%
±0.25%
±0.25%
±0.25%
±0.25%
±0.25%
±0.25%
±0.25%
±0.25%
±0.25%
±0.25%
±0.4%
±0.25%
±0.25%
±0.25%
±0.25%
±0.25%
±0.25%
±0.4%
±0.25%
±0.25%
48
24
48
48
24
48
48
24
48
48
48
24
48
24
48
24
48
48
24
48
24
48
24
48
36-75
18-36
36-75
36-75
18-36
36-75
36-75
18-36
36-75
36-75
36-75
18-36
36-75
18-36
36-75
18-36
36-75
36-75
18-36
36-75
18-36
36-75
18-36
36-75
35/0.5
50/1.8
30/0.9
35/0.6
90/2.2
45/1.1
45/0.6
50/2.4
50/1.2
45/0.9
45/1.2
80/3.1
45/1.6
50/3.5
50/1.7
90/4.4
80/2.9
45/1.2
80/3.1
45/1.6
50/3.5
50/1.7
90/4.4
80/2.9
Min.
Typ.
Package
(Case,
Pinout)
87%
85.5%
85%
87.5%
85.5%
85.5%
87%
86%
86%
88%
88.5%
87.5%
88%
89%
89%
89%
88%
88.5%
87.5%
88%
89%
89%
89%
88%
89%
87.5%
87%
89%
87.5%
87.5%
89%
88%
88%
89.5%
90.5%
89.5%
90%
91%
91%
90.5%
90%
90.5%
89.5%
90%
91%
91%
90.5%
90%
C37, P32
C37, P32
C37, P32
C37, P32
C37, P32
C37, P32
C37, P32
C37, P32
C37, P32
C37/C40, P32
C37/C40, P32
C37/C40, P32
C37/C40, P32
C37/C40, P32
C37/C40, P32
C37/C40, P32
C37/C40, P32
C37/C40, P32
C37/C40, P32
C37/C40, P32
C37/C40, P32
C37/C40, P32
C37/C40, P32
C37/C40, P32
Efficiency
➃ Nominal line voltage, no load/full load condition.
➄ Please refer to the Part Number Structure when ordering.
➅ Not all model number combinations are available. Consult Murata Power Solutions.
PART NUMBER STR UCTURE
U LQ - 3.3 / 20 - D48 N M Lx - C
Output
Configuration
RoHS-6 compliant
Pin Length Option
Quarter-Brick Package
Nominal Output Voltage
Maximum Rated Output
Surface-Mount Package
(see list above)
Remote On/Off Control Logic
Input Voltage Range
See page 16 for complete Part Number Structure.
www.murata-ps.com/support
MDC_ULQ-15A.E02 Page 2 of 17
ULQ Models
Single Output, Low-Profile, Quarter-Brick
8-25 Amp Isolated DC-DC Converters
Performance/Functional Specifications
Typical @ TA = +25°C under nominal line voltage, full-load conditions, unless noted. (1)
Input
Input Voltage Range: (2)
D24 Models
D48 Models
18-36 Volts (24V nominal)
36-75 Volts (48V nominal)
Overvoltage Shutdown
D24 Models
D48 Models
37-41 Volts (39V typical)
None (3)
Start-Up Threshold: (4)
D24 Models
D48 Models
16-18 Volts (17.5V typical)
34-36 Volts (35V typical)
Undervoltage Shutdown:
D24 Models
D48 Models
Calculated MTBF:
Operating Temperature (Ambient):
See derating curves
PCB Temperature: (4) (7)
Maximum Allowable
Thermal Shutdown
(4)
15.5-17.5 Volts (16.75V typical)
32.5-34.5 Volts (33.5V typical)
Input Current:
Normal Operating Conditions
Inrush Transient
Short Circuit
Standby Mode:
Off, UV, Thermal Shutdown
Internal Input Filter Type
Pi
1 minute duration, 5A maximum
Remote On/Off Control (Pin 2): (6)
Positive Logic ("P" Suffix Models)
On = open, open collector or
3.5-13V applied
Off = pulled low to 0-0.8V IIN = 6mA max.
Negative Logic ("N" Suffix Models)
On = pulled low to 0-0.8V IIN = 6mA max.
Off = open, open collector or
3.5-13V applied
Output
Minimum Loading
No load
VOUT Accuracy (Full Load):
Initial
Temperature Coefficient
Extreme (8)
±1.25% maximum
±0.02% per °C
±3%
VOUT Trim Range (9)
+10%, –20%
Remote Sense Compensation (4)
+10%
Ripple/Noise (20MHz BW)
See Ordering Guide
Line/Load Regulation
See Ordering Guide
Efficiency
See Ordering Guide
Isolation Voltage: Input-to-Output
2000Vdc minimum, D24 models
2250Vdc minimum, D48 models
Isolation Resistance
100MΩ
Isolation Capacitance
470pF
Current Limit Inception (98% VOUT) (10)
After warmup
+125% of maximum rated current
Short Circuit: (4)
Current
Duration
Hiccup with auto-restart
Continuous
Overvoltage Protection: (4)
OVP method
–40 to +85°C with derating
+100°C
+105 to 120°C, +115°C typical
Physical
Dimensions
See Mechanical Dimensions
Pin Material (through-hole)
Gold-plated copper alloy with nickel
underplate
Pad Material (SMT)
Copper alloy, pure tin over nickel underplate
Weight:
1 ounce (28 grams)
EMI Conducted and Radiated
FCC Part 15, EN55022 may require
external filter
Safety
UL/IEC/EN60950-1 CSA-C22.2 No. 234
4-10mA
8-50mAp-p
Reverse-Polarity Protection
(4) (14)
Primary-to-Secondary Insulation Level Basic
See Ordering Guide
0.05A2 sec maximum
50-100mA
Input Reflected Ripple Current (5)
(3)
Environmental
TBD million hours
(13)
VOUT nominal +20%
Comparator magnetic feedback
Dynamic Characteristics
Dynamic Load Response (11)
(50% Load Step)
60-300µsec, model dependent
Start-Up Time: (4) (12)
VIN to VOUT; On/Off to VOUT
30msec typical, 50msec maximum
Switching Frequency
160-300kHz, model dependent
Maximum Capacitive Load
4700 to 10,000µF, model dependent
All models are tested and specified with external output capacitors (1µF ceramic in parallel
with 10µF tantalum), unless otherwise noted. These converters have no minimum-load requirements and will effectively regulate under no-load conditions.
(2) Contact Murata Power Solutions for input voltage ranges other than those listed.
(3) See Absolute Maximum Ratings for allowable input voltages.
(4) See Technical Notes/Performance Curves for additional explanations and details.
(5) Input Ripple Current is tested/specified over a 5-20MHz bandwidth with an external 33µF input
capacitor and a simulated source impedance of 220µF and 12µH. See I/O Filtering, Input
Ripple Current and Output Noise for details.
(6) The On/Off Control is designed to be driven with open-collector (or equivalent) logic or the
application of appropriate voltages (referenced to –Input (pin 1)). See Remote On/Off Control
for more details.
(7) All models are fully operational and meet published specifications, including "cold start," at –40°C.
(8) Extreme Accuracy refers to the accuracy of either trimmed or untrimmed output voltages over
all normal operating ranges and combinations of input voltage, output load and temperature.
(9) See Output Trimming for detailed trim equations.
(10) The Current-Limit Inception point is the output current level at which the ULQ’s power-limiting
circuitry drops the output voltage 2% from its initial value. See Output Current Limiting and
Short-Circuit Protection for more details.
(11) See Performance Curves for additional information.
(12) For the Start-Up Time specifications, output settling is defined by the output voltage having
reached ±1% of its final value.
(13) MTBF’s are calculated using Telcordia (Bellcore) Method 1 Case 3, ground fixed conditions,
+40°C case temperature, and full-load conditions.
(1)
Absolute Maximum Ratings
Input Voltage:
Continuous:
Transient (100msec):
D24V Models
See OVP
NA
D48V Models
81 Volts
100 Volts
Input Reverse-Polarity Protection
Input Current must be <5A. 1 minute
duration. Fusing recommended.
Output Current
Current limited. Devices can withstand
an indefinite output short circuit.
On/Off Control (Pin 2) Max. Voltages
Referenced to –Input (pin 1)
–0.3 to +13.6 Volts
Storage Temperature
–55 to +125°C
Lead Temperature
Through-hole Soldering
SMT Soldering
+300°C, 10 seconds
Refer to solder profile
These are stress ratings. Exposure of devices to any of these conditions may adversely
affect long-term reliability. Proper operation under conditions other than those listed in the
Performance/Functional Specifications Table is not implied, nor recommended.
www.murata-ps.com/support
MDC_ULQ-15A.E02 Page 3 of 17
ULQ Models
Single Output, Low-Profile, Quarter-Brick
8-25 Amp Isolated DC-DC Converters
TECHNICAL NOTES
Input Fusing
Certain applications and/or safety agencies may require the installation of
fuses at the inputs of power conversion components. Fuses should also be
used if the possibility of sustained, non-current-limited, input-voltage polarity
reversals exists. For DATEL ULQ series DC-DC converters, we recommend
the use of a time delay fuse, installed in the ungrounded input supply line,
with a value no greater than 20 Amps.
As a rule of thumb however, we recommend the use of a normal-blow or
slow-blow fuse with a typical value about twice the maximum input current,
calculated at low line with the converter's minimum efficiency.
All relevant national and international safety standards and regulations must
be observed by the installer. For system safety agency approvals, the
converters must be installed in compliance with the requirements of the enduse safety standard, i.e. IEC/EN/UL60950.
Input Reverse-Polarity Protection
If the input voltage polarity is accidentally reversed, an internal diode will
become forward biased and likely draw excessive current from the power
source. If this source is not current limited or the circuit appropiately fused, it
could cause permanent damage to the converter.
Input Undervoltage Shutdown and Start-Up Threshold
Under normal start-up conditions, devices will not begin to regulate properly
until the ramping-up input voltage exceeds the Start-Up Threshold Voltage.
Once operating, devices will not turn off until the input voltage drops below
the Undervoltage Shutdown limit. Subsequent re-start will not occur until the
input is brought back up to the Start-Up Threshold. This built in hysteresis
prevents any unstable on/off situations from occurring at a single input
voltage.
A built-in hysterisis for all models will not allow the converter to restart until
the input voltage is sufficiently reduced.
All 48VIN models have the overvoltage shutdown function disabled, based
on requirements to withstand brief input surges and transients to 100V for
up to 100msec without voltage interruption. Contact DATEL to have input
overvoltage shutdown for 48VIN models enabled.
Input Source Impedance
The input of ULQ converters must be driven from a low ac-impedance
source. The DC-DC's performance and stability can be compromised by the
use of highly inductive source impedances. The input circuit shown in Figure
2 is a practical solution that can be used to minimize the effects of inductance in the input traces. For optimum performance, components should be
mounted close to the DC-DC converter.
I/O Filtering, Input Ripple Current, and Output Noise
All models in the ULQ Series are tested/specified for input reflected ripple
current and output noise using the specified external input/output components/circuits and layout as shown in the following two figures. External input
capacitors (CIN in Figure 2) serve primarily as energy-storage elements,
minimizing line voltage variations caused by transient IR drops in conductors
from backplane to the DC-DC. Input caps should be selected for bulk capacitance (at appropriate frequencies), low ESR, and high rms-ripple-current
ratings. The switching nature of DC-DC converters requires that dc voltage
sources have low ac impedance as highly inductive source impedance
can affect system stability. In Figure 2, CBUS and LBUS simulate a typical dc
voltage bus. Your specific system configuration may necessitate additional
considerations.
TO
OSCILLOSCOPE
Start-Up Time
The VIN to VOUT Start-Up Time is the time interval between the point at which
the ramping input voltage crosses the Start-Up Threshold and the fully loaded
output voltage enters and remains within its specified accuracy band. Actual
measured times will vary with input source impedance, external input capacitance, and the slew rate and final value of the input voltage as it appears at
the converter. The ULQ Series implements a soft start circuit to limit the duty
cycle of its PWM controller at power up, thereby limiting the input inrush current.
The On/Off Control to VOUT start-up time assumes the converter has its
nominal input voltage applied but is turned off via the On/Off Control pin. The
specification defines the interval between the point at which the converter is
turned on (released) and the fully loaded output voltage enters and remains
within its specified accuracy band.
Similar to the VIN to VOUT start-up, the On/Off Control to VOUT start-up
time is also governed by the internal soft start circuitry and external load
capacitance. The difference in start up time from VIN to VOUT and from On/Off
Control to VOUT is therefore insignificant.
Input Overvoltage Shutdown
All 24VIN ULQ DC-DC's are equipped with input overvoltage protection. Input
voltages exceeding the input overvoltage shutdown specification listed in the
Performance/Functional Specifications will cause the device to shutdown.
1
+VIN
LBUS
+
VIN
CURRENT
PROBE
CBUS
CIN
–
3
–VIN
CIN = 33μF, ESR < 700mΩ @ 100kHz
CBUS = 220μF, ESR < 100mΩ @ 100kHz
LBUS = 12μH
Figure 2. Measuring Input Ripple Current
In critical applications, output ripple/noise (also referred to as periodic and
random deviations or PARD) may be reduced below specified limits using filtering techniques, the simplest of which is the installation of additional external output capacitors. They function as true filter elements and should be
selected for bulk capacitance, low ESR and appropriate frequency response.
All external capacitors should have appropriate voltage ratings and be
located as close to the converter as possible. Temperature variations for all
relevant parameters should also be taken carefully into consideration. The
most effective combination of external I/O capacitors will be a function of
line voltage and source impedance, as well as particular load and layout
conditions. Our Applications Engineers can recommend potential solutions
and discuss the possibility of our modifying a given device's internal filtering
to meet your specific requirements. Contact our Applications Engineering
Group for additional details.
www.murata-ps.com/support
MDC_ULQ-15A.E02 Page 4 of 17
ULQ Models
Single Output, Low-Profile, Quarter-Brick
8-25 Amp Isolated DC-DC Converters
+SENSE
+VOUT
7
8
C1
C2
SCOPE
RLOAD
4
–VOUT
tion, the output voltage will decrease proportionately with increases in output
current, thereby maintaining somewhat constant power dissipation. This is
commonly referred to as power limiting. Current limit inception is defined as
the point at which the full-power output voltage falls below the specified tolerance. See Performance/Functional Specifications. If the load current, being
drawn from the converter, is significant enough, the unit will go into a short
circuit condition as described below.
Short Circuit Condition
5
–SENSE
C1 = 1μF
C2 = 10μF TANTALUM
LOAD 2-3 INCHES (51-76mm) FROM MODULE
Figure 3. Measuring Output Ripple/Noise (PARD)
Floating Outputs
Since these are isolated DC-DC converters, their outputs are "floating" with
respect to their input. Designers will normally use the –Output (pin 4) as the
ground/return of the load circuit. You can however, use the +Output (pin 8) as
ground/return to effectively reverse the output polarity.
Minimum Output Loading Requirements
ULQ converters employ a synchronous-rectifier design topology and all
models regulate within spec and are stable under no-load to full load conditions. Operation under no-load conditions however might slightly increase the
output ripple and noise.
Thermal Shutdown
The ULQ converters are equipped with thermal-shutdown circuitry. If environmental conditions cause the temperature of the DC-DC converter to rise
above the designed operating temperature, a precision temperature sensor
will power down the unit. When the internal temperature decreases below the
threshold of the temperature sensor, the unit will self start. See Performance/
Functional Specifications.
Output Overvoltage Protection
The ULQ output voltage is monitored for an overvoltage condition using a
comparator. The signal is optically coupled to the primary side and if the
output voltage rises to a level which could be damaging to the load, the sensing circuitry will power down the PWM controller causing the output voltage
to decrease. Following a time-out period the PWM will restart, causing the
output voltage to ramp to its appropriate value. If the fault condition persists,
and the output voltage again climbs to excessive levels, the overvoltage
circuitry will initiate another shutdown cycle. This on/off cycling is referred to
as "hiccup" mode.
When a converter is in current-limit mode, the output voltage will drop as
the output current demand increases. If the output voltage drops too low, the
magnetically coupled voltage used to develop primary side voltages will also
drop, thereby shutting down the PWM controller. Following a time-out period,
the PWM will restart causing the output voltage to begin ramping to their
appropriate value. If the short-circuit condition persists, another shutdown
cycle will be initiated. This on/off cycling is referred to as "hiccup" mode.
The hiccup cycling reduces the average output current, thereby preventing
internal temperatures from rising to excessive levels. The ULQ Series is
capable of enduring an indefinite short circuit output condition.
FEATURES AND OPTIONS
Remote Sense
Note: The Sense and VOUT lines are internally connected through low-value
resistors. Nevertheless, if the sense function is not used for remote regulation
the user should connect the +Sense to +VOUT and -Sense to –VOUT at the
DC-DC converter pins.
ULQ series converters employ a sense feature to provide point of use regulation, thereby overcoming moderate IR drops in pcb conductors or cabling.
The remote sense lines carry very little current and therefore require minimal
cross-sectional-area conductors. The sense lines, which are capacitively
coupled to their respective output lines, are used by the feedback control-loop
to regulate the output. As such, they are not low impedance points and must
be treated with care in layouts and cabling. Sense lines on a pcb should be
run adjacent to dc signals, preferably ground. In cables and discrete wiring
applications, twisted pair or other techniques should be implemented.
ULQ series converters will compensate for drops between the output voltage
at the DC-DC and the sense voltage at the DC-DC provided that:
[VOUT(+) –VOUT(–)] – [Sense(+) –Sense (–)] ≤ 10% VOUT
1
+VOUT
+VIN
+SENSE
7
IOUT
Sense Current
2
ON/OFF
CONTROL
TRIM
Current Limiting
6
LOAD
Sense Return
–SENSE
As soon as the output current increases to approximately 130% of its rated
value, the DC-DC converter will go into a current-limiting mode. In this condi-
Contact and PCB resistance
losses due to IR drops
8
5
IOUT Return
3
–VIN
–VOUT
4
Contact and PCB resistance
losses due to IR drops
Figure 4. Remote Sense Circuit Configuration
www.murata-ps.com/support
MDC_ULQ-15A.E02 Page 5 of 17
ULQ Models
Single Output, Low-Profile, Quarter-Brick
8-25 Amp Isolated DC-DC Converters
Output overvoltage protection is monitored at the output voltage pin, not the
Sense pin. Therefore, excessive voltage differences between VOUT and Sense
in conjunction with trim adjustment of the output voltage can cause the overvoltage protection circuitry to activate (see Performance Specifications for
overvoltage limits). Power derating is based on maximum output current and
voltage at the converter's output pins. Use of trim and sense functions can
cause output voltages to increase, thereby increasing output power beyond
the conveter's specified rating, or cause output voltages to climb into the
output overvoltage region. Therefore, the designer must ensure:
(VOUT at pins) × (IOUT) ≤ rated output power
Trimming Output Voltage
ULQ converters have a trim capability (pin 6) that enables users to adjust
the output voltage from +10% to –20% (refer to the trim equations and trim
graphs that follow). Adjustments to the output voltage can be accomplished
via a trim pot (Figure 5) or a single fixed resistor as shown in Figures 6 and 7.
A single fixed resistor can increase or decrease the output voltage depending
on its connection. Resistors should be located close to the converter and
have TCR's less than 100ppm/°C to minimize sensitivity to changes in
temperature. If the trim function is not used, leave the trim pin open.
A single resistor connected from the Trim pin (pin 6) to the +Sense (pin 7) will
increase the output voltage. A resistor connected from the Trim Pin (pin 6) to
the –Sense (pin 5) will decrease the output voltage.
Trim adjustments greater than the specified +10%/–20% can have an
adverse affect on the converter’s performance and are not recommended.
Excessive voltage differences between VOUT and Sense, in conjunction with
trim adjustment of the output voltage, can cause the overvoltage protection
circuitry to activate (see Performance Specifications for overvoltage limits).
Temperature/power derating is based on maximum output current and voltage at the converter's output pins. Use of the trim and sense functions can
cause output voltages to increase, thereby increasing output power beyond
the converter's specified rating, or cause output voltages to climb into the
output overvoltage region. Therefore:
(VOUT at pins) x (IOUT) ≤ rated output power
The Trim pin (pin 6) is a relatively high impedance node that can be susceptible to noise pickup when connected to long conductors in noisy environments. In such cases, a 0.22µF capacitor can be added to reduce this long
lead effect.
Trim Equations
ULQ-1.2/15-D48 & ULQ-1.2/25-D48
RT UP (kΩ) =
1
+VIN
+VOUT
+SENSE
2
ON/OFF
CONTROL
TRIM
–SENSE
3
–VIN
–VOUT
8
+VIN
+VOUT
+SENSE
2
ON/OFF
CONTROL
TRIM
6
5-22
TURNS
LOAD
RT UP (kΩ) =
5
3
–VIN
–VOUT
–1.413
RTDOWN (kΩ) =
1.037
1.2 – VO
–1.413
6.23(VO – 1.226)
VO – 1.5
–10.2
RTDOWN (kΩ) =
7.64
1.5 – VO
–10.2
ULQ-1.8/15-D48, ULQ-1.8/25-D24 & D48
4
RT UP (kΩ) =
7.44(VO – 1.226)
VO – 1.8
–10.2
RTDOWN (kΩ) =
9.12
1.8 – VO
–10.2
ULQ-2/15-D48, ULQ-2/15-D24 & D48
RT UP (kΩ) =
8
7
8.28(VO – 1.226)
VO – 2
–10.2
RTDOWN (kΩ) =
10.15
2 – VO
–10.2
ULQ-2.5/15-D48, ULQ-2.5/20-D24 & D48
6
LOAD
RTRIM UP
–SENSE
VO – 1.2
ULQ-1.5/15-D48, ULQ-1.5/25-D24 & D48
7
Figure 5. Trim Connections Using A Trimpot
1
1.308(VO – 0.793)
RT UP (kΩ) =
10(VO – 1.226)
VO – 2.5
–10.2
RTDOWN (kΩ) =
12.26
2.5 – VO
–10.2
5
ULQ-3.3/15-D48, ULQ-3.3/20-D24 & D48
4
RT UP (kΩ) =
Figure 6. Trim Connections To Increase Output Voltages Using Fixed Resistors
13.3(VO – 1.226)
VO – 3.3
–10.2
RTDOWN (kΩ) =
16.31
3.3 – VO
–10.2
ULQ-5/15-D24, -D48
1
+VIN
+VOUT
+SENSE
2
ON/OFF
CONTROL
TRIM
–VIN
RT UP (kΩ) =
–VOUT
20.4(VO – 1.226)
VO – 5
–10.2
RTDOWN (kΩ) =
25.01
5 – VO
–10.2
7
ULQ-12/8-D24, ULQ-12/10-D48
6
LOAD
RTRIM DOWN
–SENSE
3
8
5
RT UP (kΩ) =
49.6(VO – 1.226)
VO – 12
–10.2
RTDOWN (kΩ) =
60.45
12 – VO
–10.2
4
Figure 7. Trim Connections To Decrease Output Voltages Using Fixed Resistors
Note: Resistor values are in kΩ. Adjustment accuracy is subject to resistor
tolerances and factory-adjusted output accuracy. VO = desired output voltage.
www.murata-ps.com/support
MDC_ULQ-15A.E02 Page 6 of 17
ULQ Models
Single Output, Low-Profile, Quarter-Brick
8-25 Amp Isolated DC-DC Converters
Trim-Up Resistance vs. Percentage Increase in Output Voltage
Model ULQ-1.5
1 x 107
Model ULQ-2.5
1 x 107
1 x 106
RESISTANCE
RESISTANCE
1 x 106
1 x 105
1 x 105
1 x104
1 x104
1 x103
0
1
2
3
4
5
6
7
8
9
0
10
1
2
3
4
5
6
7
8
9
10
VOUT INCREASE (%)
VOUT INCREASE (%)
Model ULQ-1.8
1 x 107
1 x 106
1 x 106
Model ULQ-3.3
RESISTANCE
RESISTANCE
1 x 107
1 x 105
1 x 105
1 x104
1 x104
0
1
2
3
4
5
6
7
8
9
0
10
1
2
3
5
6
7
8
9
10
Trim-Down Resistance vs. Percentage Decrease
in Output Voltage
Model ULQ-2
1 x 107
4
VOUT INCREASE (%)
VOUT INCREASE (%)
1 x 107
Model ULQ-1.5
Model ULQ-1.8
Model ULQ-2
Model ULQ-2.5
Model ULQ-3.3
RESISTANCE
1 x 106
RESISTANCE
1 x 106
1 x 105
1 x 105
1 x104
0
1
2
3
4
5
6
7
8
9
10
1 x104
VOUT INCREASE (%)
0
2
4
6
8
10
12
14
16
18
20
VOUT DECREASE (%)
www.murata-ps.com/support
MDC_ULQ-15A.E02 Page 7 of 17
ULQ Models
Single Output, Low-Profile, Quarter-Brick
8-25 Amp Isolated DC-DC Converters
On/Off Control ("P" or "N" suffix)
The input-side, remote On/Off Control function (pin 2) can be ordered to
operate with either logic type:
1
"P" suffix: Standard models are equipped with Positive-logic and these
devices are enabled when pin 2 is left open (or is pulled high, applying +3.5V
to +13 with respect to –Input, pin 1) as per Figure 8. Positive-logic devices
are disabled when pin 2 is pulled low (0 to 0.8V with respect to –Input).
+VIN
+VCC
2
ON/OFF
CONTROL
"N" suffix: Optional Negative-logic devices are off when pin 2 is left open (or
pulled high, applying +3.5V to +13V), and on when pin 2 is pulled low (0 to
0.8V) with respect to –Input as shown in Figure 9.
3
–VIN
Figure 9. Driving the Negative Logic On/Off Control Pin
1
+VIN
Dynamic control of the remote on/off function is best accomplished with
a mechanical relay or an open-collector/open-drain drive circuit (optically isolated if appropriate). The drive circuit should be able to sink appropriate current (see Performance Specifications) when activated and withstand appropriate voltage when deactivated. Applying an external voltage to pin 2 when
no input power is applied to the converter can cause permanent damage
to the converter.
13V CIRCUIT
2
ON/OFF
CONTROL
3
5V CIRCUIT
–VIN
Figure 8. Driving the Positive Logic On/Off Control Pin
Surface-Mount Package ("M" suffix)
DATEL is not exempted from the Laws of Physics. And we do not have magic
solders no one else has. Nevertheless, we have a simple and practical,
straightforward approach that works. We assemble our SMT DC-DC's on
a hightemperature, plastic lead-frame (nylon 46, UL94V-0 rated) using a
high-temperature (+216°C), lead-free alloy (Sn96.2%, Ag2.5%, Cu0.8%,
Sb0.5%). The lead-frame ensures coplanarity (to within 0.004 in.) of the unit's
tin-plated (150 microinches) copper leads and also supports a removable
heat shield.
DATEL's ULQ series SMT DC-DC converters are the only higher-power (to
66W) DC-DC's that can be automatically "pick-and-placed" using standard
vacuum-pickup equipment and subsequently reflowed using high-temperature, lead-free solder.
Virtually all SMT DC-DC's today are unprotected "open-frame" devices
assembled by their vendors with high-temperature solder (usually Sn96.5/
Ag3.5 with a melting point +221°C) so that you may attach them to your
board using low-temperature solder (usually Sn63/Pb37 with a melting point
of +183°C). Conceptually straightforward, this "stepped" solder approach has
its limitations . . . and is clearly out of step with an industry trending toward
the broad use of lead-free solders. No need to experiment and develop reflow
profiles that ensure the components on their DC-DC never exceed 215216°C. If those components get too hot, "double-reflow" could compromise
the reliability of their solder joints. Virtually all these devices demand you
"cool down" the Sn63 profile you are likely using today.
The disposable heat shield, which has a cutaway exposing the package
leads, provides thermal insulation to internal components during reflow and
also doubles as the vacuum pick-up location. The insulation properties of the
heat shield are so effective that temperature differentials as high as 50°C
develop inside-to-outside the shield. Oven temperature profiles with peaks of
250-260°C and dwell times exceeding 2 minutes above 221°C (the melting
point of Sn96.5/Ag3.5) are easily achieved. DATEL's new-generation SMT
units are shipped in stackable, JEDEC-style plastic.
250
Degrees Celsius
200
Heat Shield
Test Board
Air Under Shield
150
100
50
Z1
Z2
100
Figure 10. ULQ SMT DC-DC
With Disposable Heat Shield
Z3
Z4
200
Z5
Z6
300
Z7
Seconds
400
500
600
Figure 11. Recommended Solder Profile
(When The Heat-shield Temperature Exceeds +250°C, The Air Within Is 50°C Cooler)
www.murata-ps.com/support
MDC_ULQ-15A.E02 Page 8 of 17
ULQ Models
Single Output, Low-Profile, Quarter-Brick
8-25 Amp Isolated DC-DC Converters
Typical Performance Curves, 1.5V Models
ULQ-1.5/25-D24 Efficiency vs. Line Voltage and Load Current
ULQ-1.5/25-D24
Output Current vs. Ambient Temperature
(No air flow)
92
90
30
88
25
Output Current (Amps)
Efficiency (%)
86
84
VIN = 18V
82
80
VIN = 24V
78
76
20
VIN = 18V
15
VIN = 24V
10
VIN = 36V
VIN = 36V
74
5
72
70
2.5
0
–40
5
7.5
10
12.5
15
17.5
20
22.5
0
25
30
35
40
25
45
50
55
60
65
70
75
80
85
90
95 100
80
85
90
95 100
90
95 100
Ambient Temperature (°C)
Load Current (Amps)
ULQ-1.5/15-D48 Efficiency vs. Line Voltage and Load Current
ULQ-1.5/15-D48
Output Current vs. Ambient Temperature
(No air flow)
92
90
18
88
86
Output Current (Amps)
15
Efficiency (%)
84
82
80
VIN = 36V
78
76
VIN = 48V
74
12
VIN = 36V
9
VIN = 48V
6
VIN = 75V
72
3
70
VIN = 75V
68
66
1.5
0
–40
3
4.5
6
7.5
9
10.5
12
13.5
0
25
30
35
40
45
50
55
60
65
70
75
15
Ambient Temperature (°C)
Load Current (Amps)
ULQ-1.5/25-D48 Efficiency vs. Line Voltage and Load Current
ULQ-1.5/25-D48
Output Current vs. Ambient Temperature
(VIN = 48V, air flow direction from Input pin to Output pin)
91
89
30
87
Output Current (Amps)
Efficiency (%)
25
85
83
VIN = 36V
81
79
VIN = 48V
20
0 lfm
15
100 lfm
200 lfm
10
77
73
2.5
5
VIN = 75V
75
5
7.5
10
12.5
15
17.5
Load Current (Amps)
20
22.5
25
0
–40
0
25
30
35
40
45
50
55
60
65
70
75
80
85
Ambient Temperature (°C)
www.murata-ps.com/support
MDC_ULQ-15A.E02 Page 9 of 17
ULQ Models
Single Output, Low-Profile, Quarter-Brick
8-25 Amp Isolated DC-DC Converters
Typical Performance Curves, 1.8V Models
ULQ-1.8/15-D48 Efficiency vs. Line Voltage and Load Current
ULQ-1.8/15-D48
Output Current vs. Ambient Temperature
(No air flow)
92
90
18
88
15
Output Current (Amps)
Efficiency (%)
86
84
82
80
VIN = 36V
78
76
VIN = 48V
12
VIN = 36V
9
VIN = 48V
6
VIN = 75V
74
3
72
VIN = 75V
70
68
1.5
0
–40
3
4.5
6
7.5
9
10.5
12
13.5
0
25
30
35
40
15
45
50
55
60
65
70
75
80
85
90
95 100
75
80
85
90
95 100
90
95 100
Ambient Temperature (°C)
Load Current (Amps)
ULQ-1.8/25-D24 Efficiency vs. Line Voltage and Load Current
ULQ-1.8/25-D24
Output Current vs. Ambient Temperature
(No air flow)
92
90
30
88
25
Output Current (Amps)
Efficiency (%)
86
84
82
VIN = 18V
80
VIN = 24V
78
76
74
20
VIN = 18V
15
VIN = 24V
10
VIN = 36V
VIN = 36V
72
5
70
68
2.5
5
7.5
10
12.5
15
17.5
20
22.5
0
–40
25
0
25
30
35
40
45
50
55
60
65
70
Ambient Temperature (°C)
Load Current (Amps)
ULQ-1.8/25-D48 Efficiency vs. Line Voltage and Load Current
ULQ-1.8/25-D48
Output Current vs. Ambient Temperature
(VIN = 48V, air flow direction from Input pin to Output pin)
92
90
30
88
25
84
Output Current (Amps)
Efficiency (%)
86
82
80
VIN = 36V
78
76
VIN = 48V
74
72
68
2.1
4.2
6.25
8.3
10.4
12.5
14.6
0 lfm
15
100 lfm
200 lfm
10
5
VIN = 75V
70
20
16.7 18.75 20.8
Load Current (Amps)
22.9
25
0
–40
0
25
30
35
40
45
50
55
60
65
70
75
80
85
Ambient Temperature (°C)
www.murata-ps.com/support
MDC_ULQ-15A.E02 Page 10 of 17
ULQ Models
Single Output, Low-Profile, Quarter-Brick
8-25 Amp Isolated DC-DC Converters
Typical Performance Curves, 2V Models
ULQ-2/15-D48 Efficiency vs. Line Voltage and Load Current
ULQ-2/15-D48
Output Current vs. Ambient Temperature
(No air flow)
92
90
18
88
15
Output Current (Amps)
Efficiency (%)
86
84
82
80
VIN = 36V
78
76
VIN = 48V
12
VIN = 36V
9
VIN = 48V
6
VIN = 75V
74
3
72
VIN = 75V
70
68
1.5
0
–40
3
4.5
6
7.5
9
10.5
12
13.5
0
25
30
35
40
45
15
50
55
60
65
70
75
80
85
90
95 100
75
80
85
90
95 100
Ambient Temperature (°C)
Load Current (Amps)
ULQ-2/25-D24 Efficiency vs. Line Voltage and Load Current
ULQ-2/25-D24
Output Current vs. Ambient Temperature
(No air flow)
92
90
30
88
25
Output Current (Amps)
Efficiency (%)
86
84
VIN = 18V
82
80
VIN = 24V
78
76
20
VIN = 18V
15
VIN = 24V
10
VIN = 36V
VIN = 36V
74
5
72
70
2.5
0
–40
5
7.5
10
12.5
15
17.5
20
22.5
0
25
30
35
40
25
45
50
55
60
65
70
Ambient Temperature (°C)
Load Current (Amps)
ULQ-2/25-D48 Efficiency vs. Line Voltage and Load Current
ULQ-2/25-D48
Output Current vs. Ambient Temperature
(VIN = 48V, air flow direction from Input pin to Output pin)
92
90
30
88
25
Output Current (Amps)
Efficiency (%)
86
84
82
VIN = 36V
80
78
VIN = 48V
76
74
0 lfm
100 lfm
15
200 lfm
10
5
VIN = 75V
72
70
2.5
20
5
7.5
10
12.5
15
17.5
Load Current (Amps)
20
22.5
25
0
–40
0
22
26
30
34 38
42 46
50 54
58
62
66
70
74
78 82
86
90
Ambient Temperature (°C)
www.murata-ps.com/support
MDC_ULQ-15A.E02 Page 11 of 17
ULQ Models
Single Output, Low-Profile, Quarter-Brick
8-25 Amp Isolated DC-DC Converters
Typical Performance Curves, 2.5V Models
ULQ-2.5/15-D48
Output Current vs. Ambient Temperature
(VIN = 48V, air flow direction from Input pin to Output pin)
ULQ-2.5/15-D48 Efficiency vs. Line Voltage and Load Current
94
18
92
90
15
Output Current (Amps)
Efficiency (%)
88
86
84
VIN = 36V
82
80
VIN = 48V
12
Natural Convection
100 lfm
9
200 lfm
6
300 lfm
78
400 lfm
3
76
VIN = 75V
74
72
1.5
0
–40
3
4.5
6
7.5
9
10.5
12
13.5
0
25
30
35
40
15
45
50
55
60
65
70
75
80
85
90
95 100
90
95 100
Ambient Temperature (°C)
Load Current (Amps)
ULQ-2.5/20-D48 Efficiency vs. Line Voltage and Load Current
ULQ-2.5/20-D48
Output Current vs. Ambient Temperature
(VIN = 48V, air flow direction from Input pin to Output pin)
93
91
25
Output Current (Amps)
Efficiency (%)
89
87
VIN = 36V
85
VIN = 48V
83
81
VIN = 75V
20
15
100 lfm
200 lfm
10
300 lfm
5
400 lfm
79
77
2
4
6
8
10
12
14
16
18
20
Load Current (Amps)
0
–40
0
25
30
35
40
45
50
55
60
65
70
75
80
85
Ambient Temperature (°C)
5,1$0OWER$ISSIPATIONVS,OAD#URRENT
0OWER$ISSIPATION7ATTS
6).6
6).6
6).6
,OAD#URRENT!MPS
www.murata-ps.com/support
MDC_ULQ-15A.E02 Page 12 of 17
ULQ Models
Single Output, Low-Profile, Quarter-Brick
8-25 Amp Isolated DC-DC Converters
Typical Performance Curves, 3.3V Models
ULQ-3.3/15-D48
Output Current vs. Ambient Temperature
(VIN = 48V, air flow direction from Input pin to Output pin)
ULQ-3.3/15-D48 Efficiency vs. Line Voltage and Load Current
94
18
90
Output Current (Amps)
15
Efficiency (%)
86
82
VIN = 36V
78
VIN = 48V
12
Natural Convection
100 lfm
9
200 lfm
6
300 lfm
400 lfm
3
74
VIN = 75V
0
–40
0
25
30
35
40
45
70
1
2
3
4
5
6
7
8
9
10
11
12
13
14
50
55
60
65
70
75
80
85
90
95 100
Ambient Temperature (°C)
15
Load Current (Amps)
ULQ-3.3/20-D24 Efficiency vs. Line Voltage and Load Current
ULQ-3.3/20-D24
Output Current vs. Ambient Temperature
(VIN = 24V, air flow direction from Input pin to Output pin)
93
25
91
Output Current (Amps)
Efficiency (%)
89
87
VIN = 18V
85
VIN = 24V
83
81
VIN = 36V
20
15
0 lfm
10
100 lfm
200 lfm
5
400 lfm
79
0
–40
77
2
4
6
8
10
12
14
16
18
0
25
30
35
40
20
45
50
55
60
65
70
75
80
85
90
95 100
Ambient Temperature (°C)
Load Current (Amps)
ULQ-3.3/20-D48
Output Current vs. Ambient Temperature
(VIN = 48V, air flow direction from Input pin to Output pin)
ULQ-3.3/20-D48 Efficiency vs. Line Voltage and Load Current
93
25
91
Output Current (Amps)
Efficiency (%)
89
87
VIN = 36V
85
VIN = 48V
83
20
15
100 lfm
200 lfm
10
300 lfm
81
VIN = 75V
5
79
0
–40
77
2
4
6
8
10
12
14
16
18
20
0
25
30
35
40
45
50
55
60
65
70
75
80
85
90
95 100
Ambient Temperature (°C)
Load Current (Amps)
www.murata-ps.com/support
MDC_ULQ-15A.E02 Page 13 of 17
ULQ Models
Single Output, Low-Profile, Quarter-Brick
8-25 Amp Isolated DC-DC Converters
Typical Performance Curves, 5V Models
5,1$.%FFICIENCY6S,INE6OLTAGE!ND,OAD#URRENT
5,1$.
-AXIMUM/UTPUT#URRENTVS!MBIENT4EMPERATURE
6).6AIRFLOWDIRECTIONFROM)NPUTPINTO/UTPUTPIN
%FFICIENCY
/UTPUT#URRENT!MPS
LFM
LFM
6IN6
6IN6
6IN6
6IN6
LFM
LFM
n
!MBIENT4EMPERATUREo#
,OAD#URRENT!MPS
www.murata-ps.com/support
MDC_ULQ-15A.E02 Page 14 of 17
ULQ Models
Single Output, Low-Profile, Quarter-Brick
8-25 Amp Isolated DC-DC Converters
Typical Performance Curves, 12V Models
5,1$.
%FFICIENCYVS,INE6OLTAGEAND,OAD#URRENT #
5,1$
-AXIMUM/UTPUT#URRENTVS!MBIENT4EMPERATURE
6).6TRANSVERSEAIRFLOWDIRECTIONFROMn/UTPUTTO/UTPUTPIN
/UTPUT#URRENT!MPS
%FFICIENCY
6).6
6).6
LFM
LFM
LFM
LFM
6).6
n
!MBIENT4EMPERATUREo#
,OAD#URRENT!MPS
5,1$.
%FFICIENCYVS,INE6OLTAGEAND,OAD#URRENT #
ULQ-12/10-D48
Output Current vs. Ambient Temperature
(VIN = 48V, air flow direction from Input pin to Output pin)
10.5
10
Output Current (Amps)
%FFICIENCY
6).6
6).6
9
8.5
100 lfm
8
200 lfm
7.5
300 lfm
7
6).6
500 lfm
9.5
6.5
6
–40
0
22
26
30
34 38
42 46
50 54
58
62
66
70
74
78 82
86
90
Ambient Temperature (°C)
,OAD#URRENT!MPS
5,1$0OWER$ISSIPATIONVS,OAD#URRENT
0OWER$ISSIPATION7ATTS
6).6
6).6
6).6
,OAD#URRENT!MPS
www.murata-ps.com/support
MDC_ULQ-15A.E02 Page 15 of 17
ULQ Models
Single Output, Low-Profile, Quarter-Brick
8-25 Amp Isolated DC-DC Converters
For the surface mount versions of the ULQ, use the Recommended SMT Pad
Layout illustration as a starting point to locate pads to mount the converter.
This diagram is for the pads on the mating printed circuit board—it is not
the dimensions of the lead terminals on the converter. Note: the pads are
slightly larger than the lead terminals to accomodate solder wetting and
meniscus. Also, your particular application may require some deviation from
this diagram.
3-4
,EAD
3-45NIT
0#"
#OPPER0AD
2%&
490
4HESETWOPADSAREFORALIGNMENTANDPOSITIONINGONLY
4HEYARENOTREQUIREDFORELECTRICALCONTACT
Recommended SMT Pad Layout
PART NUMBER STR UCTURE
U LQ - 3.3 / 20 - D48 N M Lx - C
Output
Configuration:
U = Unipolar
RoHS-6 Hazardous
Substance Compliant
Quarter-Brick Package
Nominal Output Voltage:
1.2,1.5, 1.8, 2, 2.5, 3.3, 5, 12 Volts
Maximum Rated Output :
Current in Amps
Input Voltage Range:
D24 = 18-36 Volts (24V nominal)
D48 = 36-75 Volts (48V nominal)
➀
➁
➂
➃
Pin Length Option: Through-hole packages only
L1 Pin length 0.110 ±0.010 inches (2.79 ±0.25mm)
L2 Pin length 0.145 ±0.010 inches (3.68 ±0.25mm)
Blank is standard pin length
Surface-Mount Package
➀
➀
➁➂
Remote On/Off Control Logic
Add "P" for positive logic
(pin 2 open = converter on)
Add "N" for negative logic
(pin 2 open = converter off)
Positive logic is standard for D24 models. Negative logic is standard for D48 models. Alternate
logic may require a special order.
Special quantity order is required; samples available with standard pin length only.
SMT (M) versions not available in sample quantities.
See list on pg. 2 using the C40 SMT package.
Some model number combinations may not be available. See website or contact your local Murata sales representative.
www.murata-ps.com/support
MDC_ULQ-15A.E02 Page 16 of 17
ULQ Models
Single Output, Low-Profile, Quarter-Brick
8-25 Amp Isolated DC-DC Converters
MECHANICAL SPECIFICATIONS
2.30 (58.4)
A
OVERALL DIMENSIONS :
2.30 (58.4) x 1.45 (36.8) x 0.70 (17.8)
BEFORE REMOVAL OF PROTECTIVE
HEAT SHIELD
2.00 (50.8)
A
B
PROTECTIVE
HEAT SHIELD
3
Case C40
Surface-mount Package
0.125
(3.2)
4
B
B
5
2
4
5
6
2
7
1
1
1.35 (34.3)
3
See page 16 for the
recommneded pad
layout dimensions.
0.600
(15.2)
8
B
0.35
(8.9)
B
PINS 1-3, 5-7:
0.040 ±0.001
(1.016 ±0.025)
PINS 4, 8:
0.062 ±0.001
(1.575 ±0.025)
PLASTIC STANDOFFS
ARE RELIEVED 0.030 (0.76)
IN SOLDER JOINT AREA
0.125 MIN.
(3.2)
0.150
(3.81)
A
1.45 (36.8)
2.22 (56.4)
B
0.375 MAX.
(9.53)
6
7
8
0.110
(2.79)
0.300
(7.6)
BOTTOM VIEW
0.600 (15.2)
4 EQ. SP. @ 0.150 (3.81)
0.600
(15.2)
0.300
(7.6)
BOTTOM VIEW
Case C37, Through-Hole Package
0.600 (15.2)
4 EQ. SP.
@ 0.150 (3.81)
DOSA-Compatible I/O Connections
Pin
1
2
3
4
Function P32
+Vin
Remote On/Off*
–Vin
–Vout
Pin
5
6
7
8
Function P32
–Sense
Trim
+Sense
+Vout
Dimensions are in inches (mm) shown for ref. only.
Third Angle Projection
Tolerances (unless otherwise specified):
.XX ± 0.02 (0.5)
.XXX ± 0.010 (0.25)
Angles ± 2˚
* The Remote On/Off can be provided with either positive ("P" suffix)
or negative ("N" suffix) logic.
Components are shown for reference only.
Murata Power Solutions, Inc.
11 Cabot Boulevard, Mansfield, MA 02048-1151 U.S.A.
ISO 9001 and 14001 REGISTERED
This product is subject to the following operating requirements
and the Life and Safety Critical Application Sales Policy:
Refer to: http://www.murata-ps.com/requirements/
Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other
technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply
the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without
notice.
© 2015 Murata Power Solutions, Inc.
www.murata-ps.com/support
MDC_ULQ-15A.E02 Page 17 of 17