DSM/DWR Models www.murata-ps.com Dual Output, 3.3V and 5V, 15Watt DC/DC Converters FEATURES Regulated 5V and 3.3V outputs 5V @ 2.65Amps/3.3V @ 3 Amps capability 15 Watts total output power Typical units 1" x 2" SMT or through-hole package Available input voltage ranges: 10-18V, 18-36V or 36-75V No-load stable operation UL/EN60950-1 safety approvals PRODUCT OVERVIEW mark available (75V-input models) For surface mount or through-hole applications requiring 15 Watts of power from 5V and 3.3V, Murata Power Solutions offers a new power sharing DC/DC converter capable of meeting your output current requirements. The DSM/DWR series is available with three different input voltage ranges: 36-75V input (D48), 18-36V input (D24) or 10-18V input (D12). These converters are fully isolated and capable of delivering any combination of 5V and 3.3V output current up to a combined total of 15 Watts of output power. Housed in 1" x 2" metal packages coated with electrically non-conductive finish, DSM/DWR converters are regulated by a 3.3V control loop that provides load regulation of ±0.5% for 3.3V output and ±1.5% for 5V output. All models include input filtering, input overvoltage and undervoltage shutdown circuitry, output shortcircuit and current-limiting protection, and thermal shutdown. All models provide trim capability and an on/off control function. Fully synchronous output rectification provides high efficiency (86%) and a stable output under no-load conditions. DSM/DWR power sharing modules offer low output ripple and noise performance, 1500 Vdc isolation voltage, and are fully specified for –40 to +100°C operation. These devices meet IEC950, UL1950 and EN60950-1 safety standards. "D48" models are CE marked (meets LVD requirements). Continuous short-circuit protection Fully isolated, 1500Vdc guaranteed –40 to +100°C operating temperature Input under and overvoltage shutdown Output OVP, thermal shutdown SIMPLIFIED SCHEMATIC +5V OUTPUT (5) +INPUT (1) SWITCH CONTROL +3.3V OUTPUT (8) –INPUT (2) ON/OFF CONTROL (3) OUTPUT RETURN (7) PWM CONTROLLER OPTO ISOLATION UV & OV COMPARATORS REFERENCE & ERROR AMP THERMAL SHUTDOWN TRIM (9) Figure 1. Simplified Schematic Typical topology is shown. For full details go to www.murata-ps.com/rohs www.murata-ps.com/support MDC_DSM/DWR Models.D01 Page 1 of 9 DSM/DWR Models Dual Output, 3.3V and 5V, 15Watt DC/DC Converters Performance Specifications and Ordering Guide ➀ Output R/N (mVp-p) ➂ Input Regulation (Max.) VOUT (Volts) IOUT ➁ (Amps) Typ. Max. Line Load ➃ DSM-5/2.65-3.3/3-D12-C DWR-5/2.65-3.3/3-D12-C 5 2.65 40 75 ±1% ±1.5% 3.3 3 60 100 ±0.5% ±0.5% DSM-5/2.65-3.3/3-D24-C DWR-5/2.65-3.3/3-D24-C 5 2.65 40 75 ±1% ±1.5% 3.3 3 60 100 ±0.5% ±0.5% DSM-5/2.65-3.3/3-D48-C DWR-5/2.65-3.3/3-D48-C 5 2.65 40 75 ±1% ±1.5% 3.3 3 60 100 ±0.5% ±0.5% Model Package (Case, Pinout) Efficiency VIN Nom. (Volts) Range (Volts) IIN ➄ (mA) Min. Typ. 12 10-18 60/1450 83% 86% C18A, P36 C34, P36 24 18-36 35/730 83% 85% C18A, P36 C34, P36 48 36-75 20/370 83% 85% C18A, P36 C34, P36 ➃ Tested from 250mA to 100% full load (other output at 250mA load). ➄ Nominal line voltage, no load/balanced full-power condition. ➀ Typical at TA = +25°C under nominal line voltage and balanced "full-load" conditions (5V @ 1.5A/3.3V @ 2.25A). ➁ Any combination of 5V/3.3V rated IOUT current, not to exceed 15 Watts of output power. (See derating graphs.) ➂ Ripple/Noise (R/N) measured over a 20MHz bandwidth. All models are specified with 0.47µF ceramic in parallel with 100µF tantalum output capacitors. As of September 2014, ONLY the following part numbers will be available: DSM-5/2.65-3.3/3-D24-C; DSM-5/2.65-3.3/3-D24L1-C; DWR-5/2.65-3.3/3-D24-C. PART NUMBER STRUCTURE DSM - 5 / 2.65 - 3.3 / 3 - D48 LX - C Dual Output: DSM: Surface-Mount Series➁ (Selective soldering only) DWR: Through-Hole Series Optional Functions RoHS-6 compliant See Optional Functions Input Voltage Range: D12 = 10-18 Volts (12V nominal) D24 = 18-36 Volts (24V nominal) D48 = 36-75 Volts (48V nominal) V1 Nominal Output Voltage: 5 Volts I1 Maximum Output Current: 2.65 Amps I2 Maximum Output Current: 3 Amps V2 Nominal Output Voltage: 3.3 Volts DSM/DWR 15 Watt DC/DC's are designed with an On/Off Control function, with positive polarity in the pin 3 position. DWR➀ Blank = On/Off Control function (positive polarity) on pin 3 only models } L1 = Pin length: 0.110 inches (2.79mm) ±0.010 L2 = Pin length: 0.145 inches (3.68mm) ±0.010 ➀ Special quantity order is required; samples available with standard pin length only. ➁ SMT (M) versions not available in sample quantities. ➂ Some model number combinations may not be available. See website or contact your local Murata sales representative. MECHANICAL SPECIFICATIONS I/O Connections 0.100 (2.54) 0.110 (2.79) 4 3 0.500 (12.70) 0.300 (7.62) 2 2.00 ±0.03 (50.80) 9 Case C18A DSM Models 8 7 6 Case C34 DWR Models 0.45 (11.43) 0.800 (20.32) 1.00 ±0.03 4 EQ. SP. @ (25.40) 0.200 (5.08) METAL CASE INSULATED PAD 0.040 ±0.001 DIA. (1.016 ±0.025) 5 1 0.20 MIN (5.08) TOP VIEW 1.800 (45.72) 0.10 (2.54) 0.10 (2.54) Pin 1 2 3 4 5 6 7 8 9 Function P36 +Input –Input On/Off Control Case +5V Output NC Output Return +3.3V Output Trim Dimensions are in inches (mm) shown for ref. only. Third Angle Projection 2.00 ±0.03 (50.80) 0.060 (1.52) 0.52 (13.21) 1 0.110 (2.79) 0.300 (7.62) 0.015 (0.38) 2 5 0.200 (5.08) 8 4 INSULATED BASE METAL CASE 0.015 (0.38) 6 7 3 9 BOTTOM VIEW 0.055 (1.40) 0.10 (2.54) 0.800 (20.32) 1.00 ±0.03 4 EQ. SP. @ (25.40) 0.200 (10.16) Tolerances (unless otherwise specified): .XX ± 0.02 (0.5) .XXX ± 0.010 (0.25) Angles ± 2˚ Components are shown for reference only. www.murata-ps.com/support MDC_DSM/DWR Models.D01 Page 2 of 9 DSM/DWR Models Dual Output, 3.3V and 5V, 15Watt DC/DC Converters Performance/Functional Specifications Typical @ TA = +25°C under nominal line voltage, balanced "full-load" conditions, unless noted. ➀ Input Input Voltage Range: D12 Models D24 Models D48 Models 10-18 Volts (12V nominal) 18-36 Volts (24V nominal) 36-75 Volts (48V nominal) Overvoltage Shutdown: D12 Models D24 Models D48 Models 18.5-21 Volts (19V typical) 37-40 Volts (38.5V typical) 77-81 Volts (79.5V typical) Start-Up Threshold: D12 Models D24 Models D48 Models 9.4-10 Volts (9.6V typical) 16.5-18 Volts (17V typical) 34-36 Volts (35V typical) Undervoltage Shutdown: D12 Models D24 Models D48 Models 7.0-8.5 Volts (8V typical) 15.5-17.5 Volts (16.5V typical) 32.5-35.5 Volts (33.5V typical) Input Current: Normal Operating Conditions Standby Mode: Off, OV, UV, Thermal Shutdown See Ordering Guide 10mA Output (continued) Short Circuit Current: 5V Output 3.3V Output 5.5 Amps average, continuous current 3 Amps average, continuous current Maximum Capacitive Loading 330µF per output Temperature Coefficient ±0.02% per °C Dynamic Characteristics Dynamic Load Response: ➁ 5V (50-100% step to 98% VOUT) 3.3V (50-100% step to 98.5% VOUT) 200µsec maximum (3.3V @ 0.25A) 200µsec maximum (5V @ 0.25A) Start-Up Time: VIN to VOUT On/Off to VOUT 10msec 10msec Switching Frequency 260kHz (±25kHz) Environmental MTBF: ➅ D12 Models D24 Models D48 Models TBD hours 2.1 million hours 2.4 million hours Operating Temperature: (Ambient): ➁ Without Derating: With Derating –40 to +60°C To +100°C (See Derating Curves) Case Temperature: Maximum Operational For Thermal Shutdown +100°C 101°C minimum, 115°C maximum –40 to +120°C Input Reflected Ripple Current ➇ 10mAp-p Internal Input Filter: Capacitive D12 Models D24 Models D48 Models 10µF 3.3µF 1.5µF Reverse-Polarity Protection: D12 Models D24 Models D48 Models 1 minute duration, 3A maximum 1 minute duration, 2A maximum 1 minute duration, 1A maximum Storage Temperature Dimensions See Mechanical Specifications On = open or to +15V, IIN @ 13V = 800µA Off = 0 to 0.8V, IIN @ 0V = 2mA Internal Case Connection Case connection via pin 4 Case Material Corrosion resistant steel with non-conductive, epoxy-based, black enamel finish and plastic baseplate Pin Material Gold-plate copper alloy pins or tin-plate copper alloy SMT contacts Weight 1.6 ounces (46 grams) On/Off Control: (Pin 3): ➂ ➄ Physical Output VOUT Accuracy: 5V Output 3.3V Output ±2.5% maximum ±1.5% maximum Minimum Loading Per Specification ➆ 250mA Minimum Load For Stability No load Ripple/Noise (20MHz BW) ➃ See Ordering Guide Line/Load Regulation See Ordering Guide Efficiency See Ordering Guide / Efficiency Curves Cross Regulation: 5V Output ([email protected], [email protected]) 3.3V Output ([email protected], [email protected]) ±2% ±0.5% Trim Range ➁ ±5% Isolation Voltage: Input-to-Output Input-to-Case Output-to-Case 1500Vdc minimum 1000Vdc minimum 1000Vdc minimum Isolation Capacitance 560pF Isolation Resistance 100MΩ Current Limit Inception: 5V @ 95% VOUT (3.3V @ 0.25A) 3.3V @ 97% VOUT (5V @ 0.25A) 3.3-4 Amps 4.7-5.7 Amps Primary to Secondary Insulation Level Operational ➀ Balanced "full-load" is 5V @ 1.5A/3.3V @ 2.25A. All models are specified with external 0.47µF ceramic and 100µF tantalum output capacitors. ➁ See Technical Notes/Graphs for details. ➂ Applying a voltage to On/Off Control (pin 3) when no input power is applied to the converter can cause permanent damage. ➃ Output noise may be further reduced with the installation of additional external output capacitors. See Technical Notes. ➄ On/Off control is designed to be driven with open collector or by appropriate voltage levels. Voltages must be referenced to the –Input (Pin 2). ➅ Demonstrated MTBF available on request. ➆ For conditions with less than minimum loading, outputs remain stable. However, regulation performance will degrade. ➇ Input Ripple Current is tested/specified over a 5-20MHz bandwidth with an external 22µF input capacitor and a simulated source impedance of 220µF and 12µH. See I/O Filtering, Input Ripple Current and Output Noise for details. www.murata-ps.com/support MDC_DSM/DWR Models.D01 Page 3 of 9 DSM/DWR Models Dual Output, 3.3V and 5V, 15Watt DC/DC Converters Absolute Maximum Ratings Input Voltage: Continuous: D12 Models D24 Models D48 Models Transient (100msec): D12 Models D24 Models D48 Models Input Reverse-Polarity Protection: ➁ D12 Models D24 Models D48 Models Output Current ➁ 21 Volts 40 Volts 81 Volts 25 Volts 50 Volts 100 Volts Input Current must be limited. 1 minute duration. Fusing recommended. 3 Amps 2 Amps 1 Amps Current limited. Devices can withstand an indefinite output short circuit. On/Off Control (Pin 3) Max. Voltages: Referenced to –Input (pin 2) +15V Storage Temperature –40 to +120°C Lead Temperature (Soldering, 10 sec.) +300°C These are stress ratings. Exposure of devices to greater than any of these conditions may adversely affect long-term reliability. Proper operation under conditions other than those listed in the Performance/Functional Specifications Table is not implied, nor recommended. TECHNICAL NOTES Isolation / Case Connection The XWR Series’ 5V and 3.3V outputs (pins 5 & 8) with its common return (pin 7) are isolated from the +VIN and –VIN inputs (pins 1 & 2) via a transformer and an opto-coupled transistor. The DC/DC converter’s case is internally connected to pin 4. This allows circuit specific grounding of the case on either the input or the output side, or leaving the case disconnected, i.e. “floating.” Input Fusing Certain applications and/or safety agencies may require the installation of fuses at the inputs of power conversion components. Fuses should also be used if the possibility of a sustained, non-current-limited, input-voltage polarity reversal exists. For XWR 15 Watt Series Converters, it is recommended to install slow blow fuses with values no greater than the following, in the +Input line. VIN Range D12 Models D24 Models D48 Models D48 models). Once operating, devices will not turn off until the input voltage drops below the Undervoltage Shutdown limit (34V for D48 models). Subsequent re-start will not occur until the input is brought back up to the Start-Up Threshold. This built in hysteresis prevents any unstable on/off situations from occurring at a single input voltage. Input voltages exceeding the input overvoltage shutdown specification listed in the Performance/Functional Specifications will cause the device to shutdown. A built-in hysteresis of 0.6 to 1.6 Volts for all models will not allow the converter to restart until the input voltage is sufficiently reduced. Start-Up Time The VIN to VOUT start-up time is the interval of time where the input voltage crosses the turn-on threshold point, and the fully loaded output voltage enters and remains within its specified accuracy band. Actual measured times will vary with input source impedance, external input/output capacitance, and the slew rate of the input voltages. The XWR 15 Watt Series implements a soft start circuit that limits the duty cycle of the PWM controller at power up, thereby limiting the Input Inrush current. The On/Off Control to VOUT start-up time assumes the converter has its nominal input voltage applied but is turned off via the On/Off Control pin. The specification defines the interval between the time at which the converter is turned on and the fully loaded output voltage enters and remains within its specified accuracy band. Similar to the VIN to VOUT start-up, the On/Off Control to VOUT start-up time is also governed by the internal soft start circuitry and external load capacitance. On/Off Control The On/Off Control (pin 3) may be used for remote on/off operation. As shown in Figure 1, the control pin is referenced to the –Input (pin 2) and will be internally pulled to a high state. The XWR Series is designed so that it is enabled when the control pin is left open (pulled high) and disabled when the control pin is pulled low (less than +0.8V relative to –Input). Dynamic control of the on/off function is best accomplished with a mechanical relay or an open-collector/open-drain circuit (optically isolated if appropriate). The drive circuit should be able to sink approximately 1 mA for logic low. The on/off control function is designed such that the converter can be disabled while the input power is ramping up, and then “released” once the input has stabilized. Fuse Value 3 Amps 2 Amps 1 Amps Input Reverse-Polarity Protection Upon applying a reverse-polarity voltage to the DC/DC converter, an internal diode will be forward biased, drawing excessive current from the power source. Therefore, it is required that the input current be limited by either an appropriately rated input fuse or a current limited power source. +Vcc 13V CIRCUIT 3 ON/OFF CONTROL 2 5V CIRCUIT –INPUT Input Overvoltage/Undervoltage Shutdown and Start-Up Threshold Under normal start-up conditions, devices will not begin to regulate until the ramping-up input voltage exceeds the Start-Up Threshold Voltage (35V for Figure 2. Internal On/Off Control circuitry www.murata-ps.com/support MDC_DSM/DWR Models.D01 Page 4 of 9 DSM/DWR Models Dual Output, 3.3V and 5V, 15Watt DC/DC Converters 5V & 3.3V Regulation Trimming Output Voltages The XWR Series converters are designed such that both the 5V and 3.3V outputs share a common regulation feedback control loop. Though the feedback loop is influenced by both outputs, the 3.3 Volt output is dominant. As a result, the 3.3 Volt regulation (0.5%) is superior to the 5 Volt regulation (1.5%). The DSM/DWR converters have a trim capability (pin 9) that allow users to adjust the output voltages ±5%. A trim adjustment will cause an equal percentage of change in both outputs. Adjustments to the output voltages can be accomplished via a trim pot, Figure 3, or a single fixed resistor as shown in Figures 4 and 5. A single fixed resistor can increase or decrease the output voltage depending on its connection. Fixed resistors should have absolute TCR's less than 100ppm/°C to minimize sensitivity to changes in temperature. The converters are specified for load regulation of minimum (250mA) to 100% loading. All models are stable under no-load conditions, but operation below minimum load mandates an increase in the regulation tolerance of ±0.5% for 3.3 Volt output and an increase of ±1% for the 5 Volt output. A slight increase in switching noise may also be observed for operation below minimum loading. Operation with a full load on 3.3 Volt output and light to no load on 5 Volt output is the most demanding for +5V regulation. Filtering and Noise Reduction The XWR Series Converters achieve their rated ripple and noise specifications with the use of 0.47µF ceramic in parallel with 100µF tantalum output capacitors. In critical applications, input/output noise may be further reduced by installing additional external I/O capacitors. Input capacitors should be selected for bulk capacitance, low ESR and high rms-ripple-current ratings. Output capacitors should be selected for low ESR and appropriate frequency response. All caps should have appropriate voltage ratings and be located as close to the converter as possible. A single resistor connected from the Trim pin (pin 9) to the +3.3V Output (pin 8), see Figure 4, will decrease the output voltages. A resistor connected from the Trim pin (pin 9) to Output Return (pin 7) will increase the output voltages. Trim adjustments greater than 5% can have an adverse effect on the converter's performance and is not recommended. 1 Current Limiting When power demands from either output fall within 120% to 190% of the rated output current, the DC/DC converter will go into a current limiting mode. In this condition, both output voltages will decrease proportionately with increases in output current, thereby maintaining a somewhat constant power dissipation. This is commonly referred to as power limiting. Current limit inception is defined as the point where the full-power output voltage falls below the specified tolerance. If the load current being drawn from the converter is significant enough, the unit will go into a short circuit condition. See “Short Circuit Condition.” ON/OFF CONTROL 4 +3.3V OUTPUT TRIM 8 +3.3V LOAD 9 Figure 3. Trim Connections Using A Trimpot 1 5 +5V OUTPUT +INPUT +5V LOAD 2 3 7 OUTPUT RETURN –INPUT ON/OFF CONTROL +3.3V LOAD 4 +3.3V OUTPUT 8 CASE TRIM RTDOWN (kΩ) = 9 R TRIM DOWN 2.49(VO – 1.234) 3.3 – VO –14 Figure 4. Decrease Output Voltage Trim Connections Using A Fixed Resistor 1 +INPUT +5V OUTPUT 5 +5V LOAD OUTPUT RETURN –INPUT Short Circuit Condition 3 Following a time-out period of 5 to 15 milliseconds, the PWM will restart, causing the output voltages to begin ramping to their appropriate values. If the short-circuit condition persists, another shutdown cycle will be initiated. This on/off cycling is referred to as “hiccup” mode. The hiccup cycling reduces the average output current, thereby preventing internal temperatures from rising to excessive levels. The modules are capable of enduring an indefinite short circuit output condition. 20kΩ 5-22 Turns CASE 2 When a converter is in current limit mode the output voltages will drop as the output current demand increases. If the output voltage drops too low, the magnetically coupled voltage used to develop primary side voltages will also drop, thereby shutting down the PWM controller. 7 OUTPUT RETURN –INPUT Thermal Shutdown These XWR converters are equipped with Thermal Shutdown Circuitry. If the internal temperature of the DC/DC converter rises above the designed operating temperature, a precision temperature sensor will power down the unit. When the internal temperature decreases below the threshold of the temperature sensor, the units will self start. +5V LOAD 2 3 5 +5V OUTPUT +INPUT ON/OFF CONTROL 4 7 +3.3V LOAD +3.3V OUTPUT 8 CASE TRIM RT UP (kΩ) = 3.073 VO – 3.3 9 R TRIM UP –14 Figure 5. Increase Output Voltage Trim Connections Using A Fixed Resistor Accuracy of adjustment is subject to tolerances or resistor values and factoryadjusted output accuracy. VO = desired output voltage. www.murata-ps.com/support MDC_DSM/DWR Models.D01 Page 5 of 9 DSM/DWR Models Dual Output, 3.3V and 5V, 15Watt DC/DC Converters Recommended PC Board Layout SMT Solder Process for DSM models A single pc board layout could accommodate both the through-hole and the SMT models of the XWR Series as per the figure below. Note that on page 2 of this data sheet, the DWR through-whole package is drawn with a bottom view of its pin locations, and the DSM surface-mount package is drawn with a top view of its pin locations. As shown, the through-hole pin locations, when viewed from the top, fall just aside (on 1.8 inch centers) the SMT pin locations, which essentially begin on 2.1 inch centers. For the surface-mount DSM models of the XWR Series, the packages’ gullwing leads are made of tin-plated (150 micro inches) copper. The gull-wing configuration, as opposed to “J” leads, was selected to keep the solder joints out from under the package to minimize both, heat conduction away from the leads (into the encapsulated package) and shadowing effects. The layout shows +Input and Case grounded on the primary side. Application dependant the primary ground could of course also be connected to -Input and Case. Creepage and clearance distances between input and output should comply with all relevant safety regulations. DSM modules do not currently withstand the standard solder-reflow process with its most common temperature profiles. In order to avoid damage to the converter a selective solder process with the following parameters must therefore be chosen (i.e. hot air gun or a hand soldering method): Pre-heat phase 30-60°C rise/minute to 150°C maximum. Lead temperature 300°C for 10 seconds maximum. 2.00 (50.80) As shown in Figure 7, our tests have determined the optimal landing-pad size to be 160 mils by 130 mils (4 x 3.3 mm). B A 1.800 (45.72) 4 B A 9 0.300 (7.62) 8 3 Case C34 1.00 (25.40) 7 2 6 0.200 (5.08) 1 5 TOP VIEW PIN LENGTH: 0.20 MIN (5.08) PIN DIAMETER: 0.040 ±0.001 (1.016 ±0.025) CASE 0.800 (20.32) 4 EQ. SP. @ 0.200 (10.16) TRIM +3.3V OUTPUT ON/OFF CONTROL OUTPUT RETURN –INPUT N.C. +5V OUTPUT +INPUT POWER GROUND 0.015 (0.38) 0.100 (2.54) 0.110 (2.79) 4 9 8 3 0.500 (12.70) 0.300 (7.62) Case C18A 2 7 6 0.800 (20.32) 4 EQ. SP. @ 0.200 (5.08) 5 1 1.00 (25.40) 0.130* (3.30) TOP VIEW 0.10 (2.54) 0.110** (2.79) 0.100** (2.54) * PAD DIMENSION ** LEAD DIMENSION 0.160* (4.06) I/O Connections Pin 1 2 3 4 5 6 7 8 9 Function P36 +Input –Input On/Off Control Case +5V Output NC Output Return +3.3V Output Trim Figure 7 . PC Board Land Pattern Figure 6. Recommended Board Layout www.murata-ps.com/support MDC_DSM/DWR Models.D01 Page 6 of 9 DSM/DWR Models Dual Output, 3.3V and 5V, 15Watt DC/DC Converters PERFORMANCE DATA D12 Models D24 Models DSM-5/2.65-3.3/3-D24 - Typical 3.3 VOUT Efficiency vs. Load (+5V @ 250mA) DSM-5/2.65-3.3/3-D12 - Typical 3.3 VOUT Efficiency vs. Load (+5V @ 250mA) 90 90 VIN = 18V 85 85 80 80 Efficiency (%) Efficiency (%) VIN = 10V VIN = 12V 75 VIN = 18V VIN = 24V 75 VIN = 36V 70 70 65 65 60 60 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 0.3 3 0.6 0.9 DSM-5/2.65-3.3/3-D12 - Typical 5 VOUT Efficiency vs. Load (+3.3V @ 250mA) 1.8 2.1 2.4 2.7 3 90 VIN = 10V VIN = 18V 85 85 80 Efficiency (%) Efficiency (%) 1.5 DSM-5/2.65-3.3/3-D24 - Typical 5 VOUT Efficiency vs. Load (+3.3V @ 250mA) 90 VIN = 12V 75 VIN = 18V 70 65 80 VIN = 24V 75 VIN = 36V 70 65 60 60 0.3 0.5 0.8 1.1 1.3 1.6 1.9 2.1 2.4 2.7 0.3 0.5 0.8 +5V Output Current (Amps) 1.1 1.3 1.6 1.9 2.1 2.4 2.7 34 36 +5V Output Current (Amps) DSM-5/2.65-3.3/3-D24 - Efficiency vs. Line and Load DSM-5/2.65-3.3/3-D12 - Efficiency vs. Line and Load 88 88 87 87 86 86 Efficiency (%) Efficiency (%) 1.2 +3.3V Output Current (Amps) +3.3V Output Current (Amps) 85 84 VOUT = [email protected]/[email protected] 83 85 84 VOUT = [email protected]/[email protected] 83 VOUT = [email protected]/[email protected] VOUT = [email protected]/[email protected] 82 82 VOUT = [email protected]/3.3V@3A VOUT = [email protected]/3.3V@3A 81 81 80 80 10 10.89 11.78 12.67 13.56 14.44 15.33 Input Voltage (Volts) 16.22 17.11 18 18 20 22 24 26 28 30 32 Input Voltage (Volts) www.murata-ps.com/support MDC_DSM/DWR Models.D01 Page 7 of 9 DSM/DWR Models Dual Output, 3.3V and 5V, 15Watt DC/DC Converters PERFORMANCE DATA D48 Models D12, 24, 48 Models DSM-5/2.65-3.3/3-D48 - Typical 3.3 VOUT Efficiency vs. Load (+5V @ 250mA) Output Power vs. Ambient Temperature VIN = Nominal, Natural Convection 90 16 VIN = 36V 14 85 Output Power (Watts) Efficiency (%) 12 80 75 VIN = 60V VIN = 75V VIN = 48V 70 10 8 6 4 2 65 0 –40 0 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 60 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 Ambient Temperature (˚C) 3 +3.3V Output Current (Amps) 3TART5PFROM6). DSM-5/2.65-3.3/3-D48 - Typical 5 VOUT Efficiency vs. Load (+3.3V @ 250mA) 6).NOMINAL6 !6 ! §&||§&TANTALUMOUTPUTCAPACITORS 90 VIN = 36V 6). 6DIV66DIV6 Efficiency (%) 85 80 VIN = 60V 75 VIN = 75V VIN = 48V 70 6/54 6/54 65 60 0.3 0.5 0.8 1.1 1.3 1.6 1.9 2.1 2.4 2.7 +5V Output Current (Amps) MSECDIV DSM-5/2.65-3.3/3-D48 - Efficiency vs. Line and Load 88 87 Efficiency (%) 86 85 84 VOUT = [email protected]/[email protected] 83 VOUT = [email protected]/[email protected] 82 VOUT = [email protected]/3.3V@3A 81 80 36 40.3 44.7 49 53.3 57.7 62 66.3 70.7 75 Input Voltage (Volts) www.murata-ps.com/support MDC_DSM/DWR Models.D01 Page 8 of 9 DSM/DWR Models Dual Output, 3.3V and 5V, 15Watt DC/DC Converters Murata Power Solutions, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1151 U.S.A. ISO 9001 and 14001 REGISTERED This product is subject to the following operating requirements and the Life and Safety Critical Application Sales Policy: Refer to: http://www.murata-ps.com/requirements/ Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without notice. © 2015 Murata Power Solutions, Inc. www.murata-ps.com/support MDC_DSM/DWR Models.D01 Page 9 of 9