Micro-actuator Driver with I2C Interface

VM114
Version
Issue Date
File Name
Total Page
:
:
:
:
PRE.001
2010/01/14
SP-VM114-PRE.001.doc
8
Micro-actuator Driver with I2C Interface
新竹市科學園區展業一路 9 號 7 樓之 1
SILICON TOUCH TECHNOLOGY INC.
9-7F-1, Prosperity Road I, Science Based Industrial Park,
Hsin-Chu, Taiwan 300, R.O.C.
Fax:886-3-5645626
Tel:886-3-5645656
VM114
VM114
Micro-actuator Driver with I2C Interface
General Specifications
VM114 is a micro-actuator driver IC with miniature package. It is one channel low
voltage bi-directional motor driver IC. The design is optimal for driving different type
micro-actuator, such as voice coil motor, piezo-actuator, or other DC motor actuators. It is
suitable for camera module application or other portable devices.
Features and Benefits
◆
Low voltage operation (VDD Min = 1.8 V)
Low input current
Zero standby current
I2C serial interface
◆
Automatic power on reset
◆
Ultra small package: WLCSP (0.78*1.27*0.35mm)
◆
◆
◆
Ordering Information
Part Number
Package
Marking
VM114 WLCSP
WLCSP, 6Pin
TBD
Micro-actuator Driver with I2C Interface
Version:PRE.001
未經授權而逕予重製、複製、使用或公開本文件,行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Page:1
VM114
Pin Assignment of WLCSP (0.78*1.27*0.35mm)
TOP View
Pin Number
Pin Name
1
VO1
Driver output 1
2
VSS
Ground
3
SCL
I2C Interface Clock Line(Serial Clock Line)
4
SDA
I2C Interface Data Line(Serial Data Line)
5
VO2
Driver output 2
6
VDD
Power supply
Micro-actuator Driver with I2C Interface
Description
Version:PRE.001
未經授權而逕予重製、複製、使用或公開本文件,行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Page:2
VM114
Absolute Maximum Ratings ( Unless otherwise noted, TA= 25℃ )
Characteristic
Symbol
Rating
Unit
Supply Voltage
VDD
4.5
V
Input Voltage
VP1
VDD+0.4
V
IO Peak Current
IOPeak
400
mA
IODC Current
IODC
280
mA
Power Dissipation
PD
300
mW
Operating Temperature Range
TOPR
-40 ~ 80
°C
Storage Temperature Range
TSTG
-65 ~ 150
°C
Electrical Characteristic
(Unless otherwise noted, TA= 25℃ & VDD=2.8V)
Characteristic
Sym.
Supply Voltage
VDD
Standby Current
IDD
Condition
No load
Limit
Unit
Min.
Typ.
Max.
1.8
2.8
4.5
V
-
-
3
μA
SDA SCL Input Terminal ( TJ = 25℃)
Input Voltage “H”
VIH
-
0.5*VDD
-
VDD+0.4
V
Input Voltage “L”
VIL
-
-0.4
-
0.2*VDD
V
Input Current “H”
IIH
VIN = VDD
-
-
±1
μA
Input Current “L”
IIL
VIN = 0 V
-
-
±1
μA
Output Terminal (O1, O2)
Output Resistance (Upper)
ROH
IOUT=200mA
-
1.3
1.6
Ohm
Output Resistance (Low)
ROL
IOUT=200mA
-
0.7
0.9
Ohm
Micro-actuator Driver with I2C Interface
Version:PRE.001
未經授權而逕予重製、複製、使用或公開本文件,行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Page:3
VM114
Data Format
VM114 Write Mode
In the writing mode, data is written to VM114 and shifted into a 8-bit input register. After all
8 bits of data have been shifted in, a STOP signal is generated by master controller. The
data in the input register is transferred to VM114 internal controller at the same time.
VM114 Read Mode
In reading mode, data is read from IC to a master controller in the same bit order.
Table
Address
6
5
4
3
2
1
0
Serial Data Bits 7
ID6 ID5 ID4 ID3 ID2 ID1 ID0 R/W
Function
7
0
6
0
5
0
Data
4
3
0
0
D[1:0]: The output O1/O2 is set by D[1:0] as defined below.
Micro-actuator Driver with I2C Interface
Version:PRE.001
未經授權而逕予重製、複製、使用或公開本文件,行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Page:4
2
0
1
D1
0
D0
VM114
Input
Output
D1
D0
O1
O2
0
0
H
H
0
1
H
L
1
0
L
H
1
1
L
L
Function Block
1μF
VDD
SDA
O1
I2C Interface
M1
& Controller
SCL
O2
GND
Application Notes
…
…
The O1/O2 output H/H or L/L will brake the motor. Though the active current of
driver is near to zero, if the application is required to turn off driver, please turn off
the driver’s power from VDD.
The capacitor connected between the output nodes O1/O2 will reduce the noise
generated by the motor when the motor is switched to opposed direction.
Micro-actuator Driver with I2C Interface
Version:PRE.001
未經授權而逕予重製、複製、使用或公開本文件,行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Page:5
VM114
Package Specifications (WLCSP1): (0.78*1.27*0.35mm)
DIMENSION
(mm)
SYMBOL
MIN.
0.325
0.090
0.235
0.234
1.255
0.765
0.380
0.380
0.215
0.170
A
A1
A2
b
D
E
e1
e2
L1
L2
Micro-actuator Driver with I2C Interface
NOM.
0.350
0.100
0.250
0.260
1.270
0.780
0.400
0.400
0.235
0.190
Version:PRE.001
未經授權而逕予重製、複製、使用或公開本文件,行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
MAX.
0.375
0.110
0.265
0.286
1.285
0.795
0.420
0.420
0.255
0.210
Page:6
VM114
The products listed herein are designed for ordinary electronic applications, such as
electrical appliances, audio-visual equipment, communications devices and so on.
Hence, it is advisable that the devices should not be used in medical instruments,
surgical implants, aerospace machinery, nuclear power control systems,
disaster/crime-prevention equipment and the like. Misusing those products may
directly or indirectly endanger human life, or cause injury and property loss.
Silicon Touch Technology, Inc. will not take any responsibilities regarding the
misusage of the products mentioned above. Anyone who purchases any products
described herein with the above-mentioned intention or with such misused
applications should accept full responsibility and indemnify. Silicon Touch Technology,
Inc. and its distributors and all their officers and employees shall defend jointly and
severally against any and all claims and litigation and all damages, cost and
expenses associated with such intention and manipulation.
Micro-actuator Driver with I2C Interface
Version:PRE.001
未經授權而逕予重製、複製、使用或公開本文件,行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Page:7