SMT POWER INDUCTORS Power Beads - PA2607NL and PA2607AHL Series Current Rating: Over 90Apk Inductance Range: 115nH to 300nH Height: 7.5mm and 7.6mm Max Footprint: 10.4mm x 7.9mm Max Halogen Free Electrical Specifications @ 25°C â Operating Temperature -40°C to +130°C 7 Inductance1 @ 0ADC (nH +/- 15%) 115 150 175 215 230 270 300 Part Number PA2607.121NL PA2607.151NL PA2607.181NL PA2607.211NL PA2607.231NL PA2607.271NL PA2607.301NL Inductance @Irated (nH TYP) Irated 2 (ADC) 115 150 175 195 208 241 260 41 41 41 41 37 31 27 DCR 3 (mW nominal) 0.29 +/- 7% (.XXNL) 0.29 +/- 5% (.XXXAHL) NOTES: 1. Inductance measured at 100kHz, 100mVrms. 2. The rated current as listed is either the saturation current or the heating current depending on which value is lower. 3. The nominal DCR is measured from point a to point b , as shown below on the mechanical drawing. The standard part (PA2607.XXXNL) has a DCR tolerance of +/-7%. A tighter DCR tolerance of +/-5% is available by changing the NL suffix to AHL (i.e. PA2607.211NL becomes PA2607.211AHL). 4. The saturation current is the typical current which causes the inductance to drop by 20% at the stated ambient temperatures (25°C and 100°C). This current is determined by placing the component in the specified ambient environment and applying a short duration pulse current (to eliminate self-heating effects) to the component. Saturation Current 4 (A TYP) 25°C 94 72 62 48 43 37 32 Heating Current (A TYP) 100°C 80 61 53 41 37 34 28 Height mm* (inches) 7.4* (.291) 41 7.3* (.287) 5. The heating current is the DC current which causes the part temperature to increase by approximately 40°C. 6. In high volt*time applications, additional heating in the component can occur due to core losses in the inductor which may neccessitate derating the current in order to limit the temperature rise of the component. To determine the approximate total losses (or temperature rise) for a given application, the coreloss and temperature rise curves can be used. 7.Optional Tape & Reel packaging can be ordered by adding a âTâ suffix to the part number (i.e. PA2607.211NL becomes PA2607.211NLT). Pulse complies to industry standard tape and reel specification EIA481. The tape and reel for this product has a width (W=24mm), pitch (Po=16.0mm) and depth (Ko=7.6mm). 8. The temperature of the component (ambient plus temperature rise) must be within the stated operating temperature range. Mechanical Schematic PA2607.XXXNL PA2607 .XXXNL D/C CTRY * Please note that marking shown is for the PA2607.XXXNL parts. Marking for AHL parts is the same except PA2607.XXXNL is replaced by PA2607.XXXAHL. .008 0.2 Weight . . . . . . . . . . . 2.4 grams Tape & Reel . . . . . . . . . 400/reel Dimensions: Inches mm Unless otherwise specified, all tolerances are ± .010 0,25 1 pulseelectronics.com P673.H (05/14) SMT POWER INDUCTORS Power Beads - PA2607NL and PA2607AHL Series B Pulse Worldwide Headquarters 12220 World Trade Drive San Diego, CA 92128 U.S.A. 0.37 Pulse Europe Einsteinstrasse 1 D-71083 Herrenberg Germany Pulse China Headquarters Pulse North China Pulse South Asia Pulse North Asia B402, Shenzhen Academy of Room 2704/2705 135 Joo Seng Road 3F, No. 198 Aerospace Technology Bldg. Super Ocean Finance Ctr. #03-02 Zhongyuan Road 10th Kejinan Road 2067 Yan An Road West PM Industrial Bldg. Zhongli City High-Tech Zone Shanghai 200336 Singapore 368363 Taoyuan County 320 Nanshan District China Taiwan R. O. C. Shenzen, PR China 518057 Tel: 886 3 4356768 Tel: 858 674 8100 Tel: 49 7032 7806 0 Tel: 86 755 33966678 Tel: 86 21 62787060 Tel: 65 6287 8998 Fax: 886 3 4356823 (Pulse) Fax: 858 674 8262 Fax: 49 7032 7806 135 Fax: 86 755 33966700 Fax: 86 2162786973 Fax: 65 6287 8998 Fax: 886 3 4356820 (FRE) Performance warranty of products offered on this data sheet is limited to the parameters specified. Data is subject to change without notice. Other brand and product names mentioned herein may be trademarks or registered trademarks of their respective owners. © Copyright, 2014. Pulse Electronics, Inc. All rights reserved. 2 pulseelectronics.com P673.H (05/14)