SMT Power Inductors Round wire Coils– PG1096NL series Height: 14.8mm Max No Thermal Aging RoHS Compliant Inductance Range: 1.5uH to 82uH Current Rating: up to 65Apk Footprint: 26mm x 26mm Max Electrical Specifications @ 25°C - Operating Temperature -40°C to 130°C1 Inductance @ Irated2 µH TYPICAL Part Number Controlled Electrical Specs. Irated 3 (A) Saturation 5 Current Isat (A TYP) DCR 4 (mΩ) MAX Inductance @ 0Adc (µH ± 20%) 25°C 100°C Heating Current 6 Idc (A TYP) Core Loss Factor 7 (K2) PG1096.152NL 1.35 50 0.85 1.5 65 50.5 50 27.9 PG1096.252NL 2.25 45 1.2 2.5 55 43 45 31 PG1096.472NL 4.2 35 1.8 4.7 40 31 35 43.7 PG1096.682NL 6 30 2 6.8 35 27.5 30 50.6 PG1096.103NL 9 24.5 3.15 10 28 21.8 24.5 62 PG1096.183NL 16 18.5 5 18 21 16.5 18.5 83.6 PG1096.223NL 19.5 17 5.5 22 19 14.8 17 90.9 PG1096.333NL 29.5 13.5 10.5 33 15.5 12 13.5 111.5 PG1096.473NL 42.3 11 12.5 47 13 10 11 134.4 PG1096.683NL 61 9.5 15 68 11 8.6 9.5 168.5 PG1096.823NL 73.5 8.5 22 82 10 7.8 8.5 179.3 Notes: 1. Actual temperature of the component during system operation (ambient plus the components’ performance varies depending on the system condition. It is sugtemperature rise) must be within the standard operating range. gested that the component be tested at the system level, to verify the temperature 2. Inductance at Irated is a typical inductance value for the component taken at rated rise of the component during system operation. current. 7. Core loss approximation is based on published core data: 3. The rated current as listed is either the saturation current (@ 25°C) or the heating Core Loss = K1 * (f)1.42 * (K2ΔI)2.57 in mW K1=2.86E-06 (2.50E-06 FOR PG1096.152NL) current depending on which value is lower. f = switching frequency in KHz 4. The DCR of the part is measured at an ambient temperature of 20°C±3°C from point a K1 & K2 = core loss factors to b as shown below on the mechanical drawing. ΔI= delta I across the component in Ampere 5. The saturation current, Isat, is the current at which the component inductance drop K2ΔI=one half of the peak to peak flux density across the component in Gauss by 20% (typical) at an ambient temperature. This current is determined by placing the component in the specified ambient environment and applying a short duration 8. Unless otherwise specified, all testing is made at 100kHz, 0.1Vac pulse current (to eliminate self-heating effect) to the component. 6. The heating current, Idc, is the DC current required to raise the component tempera- 9. Optional Tape & Reel packaging can be ordered by adding a “T” suffix to the part number (i.e. PG1096.223NL becomes PG1096.223NLT). Pulse complies with industry ture by approximately 40°C. The heating current is determined by mounting the standard tape and reel specification EIA481. The tape and reel for this product has a component on a typical PCB and applying current for 30 minutes. The temperature is width (W=44.0mm), pitch (Po=36.0mm) and depth (Ko=15.6mm). measured by placing the thermocouple on top of the unit under test. Take note that 1 pulseelectronics.com P745.A (10/14) SMT Power Inductors Round wire Coils– PG1096NL series Mechanicals PG1096.XXXNL Schematic 1 1.024 MAX [26.00] 3 2 1.024 MAX [26.00] H 3 PG1096.XXXNL D DATE CODE CTRY MFG .006[0.15] a 1 b FRONT VIEW 2 TOP VIEW 3 Part Number .197 [5.00] (.138) [(3.50)] .197 [5.00] 1.043 [26.50] .102 [2.60] X .138 [3.50] 2 P BOTTOM VIEW 1 .217 [5.50] *PIN 3 IS FOR MECHANICAL SUPPORT ONLY AND HAS NO INTERNAL ELECTRICAL CONNECTION .472 [12.00] .866 [22.00] SUGGESTED LAND PATTERN PG1096.152NL PG1096.252NL PG1096.472NL PG1096.682NL PG1096.103NL PG1096.183NL PG1096.223NL PG1096.333NL PG1096.473NL PG1096.683NL PG1096.823NL Lead Width (X) Ref 3.0mm 3.0mm 3.0mm 3.0mm 3.0mm 3.0mm 3.0mm 3.0mm 3.0mm 3.0mm 2.3mm H (Height) 13mm P (Pin Pitch) 17.00±1.00mm 14.8mm 17.00±1.70mm Weight..........................34.0 grams (28.0 grams for PG1096.152NL) Tape and Reel....................60/reel Dimensions: Inches mm Unless otherwise specified, all tolerences are ± 2 pulseelectronics.com 0.01 0.25 P745.A (10/14) SMT Power Inductors Round wire Coils– PG1096NL series Inductance Charts PG1096.XXXNL Typical Inductance vs DC Bias Typical Inductance vs DC Bias 10 .152NL@25ºC .152NL@100ºC .252NL@25ºC .252NL@100ºC .472NL@25ºC .472NL@100ºC .682NL@25ºC .682NL@100ºC .103NL@25ºC .103NL@100ºC 8 INDUCTANCE(uH) 7 .183NL@25ºC .183NL@100ºC .223NL@25ºC .223NL@100ºC .333NL@25ºC .333NL@100ºC .473NL@25ºC .473NL@100ºC .683NL@25ºC .683NL@100ºC .823NL@25ºC .823NL@100ºC 80 70 60 INDUCTANCE(uH) 9 6 5 50 40 4 30 3 20 2 1 0 10 20 30 40 50 60 70 DC Bias (A) 80 10 0 5 10 15 20 DC Bias (A) For More Information Pulse Worldwide Headquarters 12220 World Trade Drive San Diego, CA 92128 U.S.A. Pulse Europe Zeppelinstrasse 15 71083 Herrenberg Germany Pulse China Headquarters Pulse North China Pulse South Asia Pulse North Asia B402, Shenzhen Academy of Room 2704/2705 135 Joo Seng Road 3F No. 198, Zhongyuan Road Aerospace Technology Bldg. Super Ocean Finance Ctr. #03-02 Zhongli City 10th Kejinan Road 2067 Yan An Road West PM Industrial Bldg. Taoyuan County (32068) High-Tech Zone Shanghai 200336 Singapore 368363 Taiwan Nanshan District China Shenzhen, PR China 518057 Tel: 858 674 8100 Tel: 49 7032 7806 0 Tel: 86 755 33966678 Tel: 86 21 62787060 Tel: 65 6287 8998 Tel: 886 3 4356768 Fax: 858 674 8262 Fax: 49 7032 7806 12 Fax: 86 755 33966700 Fax: 86 2162786973 Fax: 65 6287 8998 Fax: 886 3 4356823 Performance warranty of products offered on this data sheet is limited to the parameters specified. Data is subject to change without notice. Other brand and product names mentioned herein may be trademarks or registered trademarks of their respective owners. © Copyright, 2014. Pulse Electronics, Inc. All rights reserved. 3 pulseelectronics.com P745.A (10/14) 25