RECTRON FFM1600W SEMICONDUCTOR TECHNICAL SPECIFICATION FAST RECOVERY RECTIFIER VOLTAGE 1600 Volts CURRENT 0.5 Ampere FEATURES Fast switching Low leakage Low forward voltage drop High current capability High currenf surge High reliability SMX MECHANICAL DATA .209 (5.31) .185 (4.70) Case: Molded plastic Epoxy: Device has UL flammability classification 94V-O Lead: MIL-STD-202E method 208C guaranteed Mounting position: Any .110 (2.79) .086 (2.18) .011 (0.28) .007 (0.18) .067 (1.70) .051 (1.30) .180 (4.57) .160 (4.06) .091 (2.31) .067 (1.70) .008 (0.20) * * * * .010 (0.25) * * * * * * MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 o C ambient temperature unless otherwise specified. .059 (1.50) .035 (0.89) Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. Dimensions in inches and (millimeters) MAXIMUM RATINGS (At T A = 25 oC unless otherwise noted) SYMBOL FFM1600W UNITS Maximum Recurrent Peak Reverse Voltage VRRM 1600 Volts Maximum RMS Voltage VRMS 1120 VDC 1600 Volts Volts IO 0.5 Amps I FSM 25 Amps CJ 15 T J , T STG -65 to + 150 SYMBOL VF FFM1600W 1.8 UNITS Volts 5.0 uAmps 100 uAmps 300 nSec RATINGS Maximum DC Blocking Voltage Maximum Average Forward Rectified Current at T A = 25 oC Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Typical Junction Capacitance (Note 2) Operating and Storage Temperature Range pF 0 C ELECTRICAL CHARACTERISTICS (At TA = 25oC unless otherwise noted) CHARACTERISTICS Maximum Instantaneous Forward Voltage at 0.5A DC Maximum DC Reverse Current at Rated DC Blocking Voltage TA = 25 oC Maximum Full Load Reverse Current Full Cycle Average, .375” (9.5mm) lead length at T L = 55 oC Maximum Reverse Recovery Time (Note 1) NOTES : 1. Reverse Recovery Test Conditions: IF = 0.5A, IR = -1.0A, IRR =- 0.25A 2. Measured at 1 MHZ and applied reverse voltage of 4.0 volts IR trr 2002-6 FIG. 1 - TYPICAL FORWARD CURRENT DERATING CURVE FIG. 2 - MAXIMUM NON-REPETITIVE FORWARD PEAK FORWARD SURGE CURRENT, (A) AVERAGE FORWARD CURRENT, (mA) RATING AND CHARACTERISTIC CURVES ( FFM1600W ) 500 Single Phase Half Wave 60Hz Inductive or Resistive Load 400 300 200 100 0 0 50 100 150 AMBIENT TEMPERATURE, ( 175 SURGE CURRENT 35 30 8.3ms Single Half Sine-Wave (JEDEC Method) 25 20 15 10 5 0 1 10 ) NUMBER OF CYCLES AT 60Hz FIG. 3 - TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC 50 NONINDUCTIVE 10 NONINDUCTIVE trr +0.5A (+) 25 Vdc (approx) (-) (-) D.U.T PULSE 0 GENERATOR (NOTE 2) 1 NONINDUCTIVE OSCILLOSCOPE (NOTE 1) NOTES:1 Rise Time = 7ns max. Input Impedance = 1 megohm. 22 pF. 2. Rise Time = 10ns max. Source Impedance = 50 ohms. -0.25A (+) -1.0A 1cm SET TIME BASE FOR 50/100 ns/cm RECTRON 100