ESM101 THRU ESM107 SURFACE MOUNT GLASS PASSIVATED SUPER FAST SILICON RECTIFIER VOLTAGE RANGE 50 to 600 Volts CURRENT 1.0 Ampere d e u n i nt FEATURES * * * * * * Glass passivated device Ideal for surface mounted applications Low leakage current Metallurgically bonded construction Mounting position: Any Weight: 0.015 gram MECHANICAL DATA o c is D MELF * Epoxy : Device has UL flammability classification 94V-0 DISCONTINUED- .205 ( 5.2 ) .190 ( 4.8 ) "This series is replaced by the EFM10X series that meets to the same fit and function parameters and share the same solder pad layout. The EFM10X series is preferred for error-free vacuum pick-up and PCB assembly.＂ SOLDERABLE ENDS .024 ( 0.6 ) .016 ( 0.4 ) .106 ( 2.7 ) .095 ( 2.4 ) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 o C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. Dimensions in inches and (millimeters) MAXIMUM RATINGS (@ TA=25 OC unless otherwise noted) RATINGS SYMBOL ESM101 ESM102 ESM103 ESM104 ESM105 ESM106 ESM107 UNITS Maximum Recurrent Peak Reverse Voltage VRRM 50 100 150 200 300 400 600 Volts Maximum RMS Voltage VRMS 35 70 105 140 210 280 420 Volts VDC 50 100 150 200 300 400 600 Volts Maximum DC Blocking Voltage Maximum Average Forward Rectified Current at TA = 55oC IO Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Typical Junction Capacitance (Note 2) Operating and Storage Temperature Range 1.0 IFSM CJ Amps 30 Amps 15 10 pF T J, TSTG -55 to + 150 SYMBOL ESM101 ESM102 ESM103 ESM104 ESM105 ESM106 ESM107 0 C ELECTRICAL CHARACTERISTICS (@TA=25 OC unless otherwise noted) CHARACTERISTICS Maximum Instantaneous Forward Voltage at 1.0A DC Maximum DC Reverse Current at Rated DC Blocking Voltage VF @TA = 25oC @TA = 100oC Maximum Reverse Recovery Time (Note 1) NOTES : 1. Reverse Recovery Test Conditions: IF = 0.5A, IR = -1.0A, IRR = -0.25A 2. Measured at 1 MHZ and applied reverse voltage of 4.0 volts 3. “Fully ROHS compliant”, “100% Sn plating (Pb-free)”. 0.95 1.25 5.0 IR trr 1.50 Volts uAmps 100 35 UNITS 50 nSec 2007-4 RATING AND CHARACTERISTICS CURVES ( ESM101 THRU ESM107 ) 50 W NONINDUCTIVE (+) 25 Vdc (approx) (-) (-) D.U.T PULSE GENERATOR (NOTE 2) 1W NONINDUCTIVE trr +0.5A 10 W NONINDUCTIVE OSCILLOSCOPE (NOTE 1) 0 -0.25A (+) NOTES: 1 Rise Time = 7ns max. Input Impedance = 1 megohm. 22pF. -1.0A 2. Rise Time = 10ns max. Source Impedance = 50 ohms. 1cm SET TIME BASE FOR 50/100 ns/cm AVERAGE FORWARD CURRENT, (A) 1.25 1.00 0.75 0.50 Single Phase Half Wave 60Hz Resistive or Inductive Load 0.25 0 0 25 50 75 100 125 150 AMBIENT TEMPERATURE, (OC) FIG.2 TYPICAL FORWARD CURRENT DERATING CURVE 175 INSTANTANEOUS REVERSE CURRENT, (uA) FIG.1 TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC 1000 100 TA = 100 OC TA = 75 OC 10 TA = 25 OC 1.0 0.1 0 20 40 60 80 100 120 PERCENT OF RATED PEAK REVERSE VOLTAGE, (%) FIG.3 TYPICAL REVERSE CHARACTERISTICS 140 PEAK FORWARD SURGE CURRENT, (A) 20 10 TJ = 25 OC 3.0 ESM107 1.0 ESM105~ESM106 0.3 0.1 ESM101~ESM104 0.03 0.01 Pulse Width=300uS 1% Duty Cycle 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 200 8.3ms Single Half Sine-Wave (JEDED Method) 100 50 30 20 10 1 5 INSTANTANEOUS FORWARD VOLTAGE, (V) 10 TJ = 25 OC 100 60 40 ESM101~ESM104 20 10 6 4 ESM105~ESM107 2 0.1 0.2 100 FIG.5 MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 200 1 50 NUMBER OF CYCLES AT 60Hz FIG.4 TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS JUNCTION CAPACITANCE, (pF) INSTANTANEOUS FORWARD CURRENT, (A) RATING AND CHARACTERISTICS CURVES ( ESM101 THRU ESM107 ) 0.4 1.0 2 4 10 20 40 REVERSE VOLTAGE, (V) FIG.6 TYPICAL JUNCTION CAPACITANCE 100 Mounting Pad Layout F-SLOT WIDTH OPTIMUM PAD SIZE .100 (2.54) .100 (2.54) .100 (2.54) .200 (5.08) .300 (7.62) Dimensions in inches and (millimeters) DISCLAIMER NOTICE Rectron Inc reserves the right to make changes without notice to any product specification herein, to make corrections, modifications, enhancements or other changes. Rectron Inc or anyone on its behalf assumes no responsibility or liability for any errors or inaccuracies. Data sheet specifications and its information contained are intended to provide a product description only. "Typical" parameters which may be included on RECTRON data sheets and/ or specifications can and do vary in different applications and actual performance may vary over time. Rectron Inc does not assume any liability arising out of the application or use of any product or circuit. Rectron products are not designed, intended or authorized for use in medical, life-saving implant or other applications intended for life-sustaining or other related applications where a failure or malfunction of component or circuitry may directly or indirectly cause injury or threaten a life without expressed written approval of Rectron Inc. Customers using or selling Rectron components for use in such applications do so at their own risk and shall agree to fully indemnify Rectron Inc and its subsidiaries harmless against all claims, damages and expenditures.