SE1L THRU SE4L SURFACE MOUNT SUPER FAST RECTIFIER VOLTAGE RANGE 50 to 200 Volts CURRENT 1.0 Ampere FEATURES * * * * * * * High reliability Low leakage Low forward voltage High current capability Super fast switching speed High surge capability Good for switching mode circuit SOD-123FL .114 (2.9) .106 (2.7) MECHANICAL DATA * * * * * Case: Molded plastic Epoxy: Device has UL flammability classification 94V-O Lead: MIL-STD-202E method 208C guaranteed Mounting position: Any Weight: 0.016 gram .035 (0.90) .077 (1.95) .028 (0.70) .069 (1.75) .008 (0.20) .039 (1.00) .035 (0.90) .150 (3.8) .142 (3.6) .052 (1.32) .050 (1.28) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 o C ambient temperature unless otherwise specified. .033 (0.85) Single phase, half wave, 60 Hz, resistive or inductive load. .030 (0.75) .033 (0.85) .044 (1.12) .030 (0.75) .043 (1.08) For capacitive load, derate current by 20%. Dimensions in inches and (millimeters) MAXIMUM RATINGS (At T A = 25oC unless otherwise noted) RATINGS SYMBOL SE1L SE2L SE3L SE4L UNITS Maximum Recurrent Peak Reverse Voltage VRRM 50 100 150 200 Volts Maximum RMS Volts VRMS 35 70 105 140 Volts VDC 50 100 150 200 Volts Maximum DC Blocking Voltage Maximum Average Forward Current at T A = 55 oC IO Peak Forward Surge Current I FM (surge):8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Typical Junction Capacitance (Note 2) Operating and Storage Temperature Range 1.0 Amps I FSM 25 Amps CJ 20 pF T J , T STG -55 to + 150 0 C ELECTRICAL CHARACTERISTICS (At TA = 25oC unless otherwise noted) CHARACTERISTICS Maximum Forward Voltage at 1.0 A DC SYMBOL VF Maximum DC Reverse Current @T A = 25 o C at Rated DC Blocking Voltage @T A =100 o C Maximum Reverse Recovery Time (Note 1) NOTES : 1. Test Conditions: IF=0.5A, I R=-1.0A, IRR=-0.25A. 2. Measured at 1 MHZ and applied reverse voltage of 4.0 volts. 3.“Fully ROHS compliant”, “100% Sn plating (Pb-free)”. IR trr SE1L SE2L SE3L 0.95 5.0 100 35 SE4L UNITS Volts uAmps nSec 2006-3 REV:O RATING AND CHARACTERISTIC CURVES ( SE1L THRU SE4L ) FIG. 1 - TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC 10 NONINDUCTIVE +0.5A (-) D.U.T (+) 25 Vdc (approx) (-) 0 PULSE GENERATOR (NOTE 2) 1 NONINDUCTIVE OSCILLOSCOPE (NOTE 1) -0.25A (+) -1.0A NOTES:1 Rise Time = 7ns max. Input Impedance = 1cm 1 megohm. 22pF. 2. Rise Time = 10ns max. Source Impedance = 50 ohms. SET TIME BASE FOR 10 ns/cm FIG. 3 - TYPICAL REVERSE CHARACTERISTICS 100 TJ = 100 10 TJ = 25 .1 0 20 40 60 80 100 120 20 15 10 5 0 1 2 5 10 20 50 NUMBER OF CYCLES AT 60Hz 100 0 25 50 75 100 125 150 175 AMBIENT TEMPERATURE ( TJ = 25 Pulse Width = 300uS 1% Duty Cycle .01 0 .2 .4 .6 .8 1.0 1.2 1.4 INSTANTANEOUS FORWARD VOLTAGE, (V) FIG. 6 - TYPICAL JUNCTION CAPACITANCE JUNCTION CAPACITANCE, (pF) PEAK FORWARD SURGE CURRENT, (A) 25 0 .1 FIG. 5 - MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 8.3ms Single Half Sine-Wave (JEDEC Method) 1.0 1.0 PERCENT OF RATED PEAK REVERSE VOLTAGE, (%) 30 Single Phase Half Wave 60Hz Resistive or Inductive Load CHARACTERISTICS 10 .001 140 35 2.0 FIG. 4 - TYPICAL INSTANTANEOUS FORWARD INSTANTANEOUS FORWARD CURRENT, (A) INSTANTANEOUS REVERSE CURRENT, (uA) 1000 1.0 FIG. 2 - TYPICAL FORWARD CURRENT DERATING CURVE trr AVERAGE FORWARD CURENT, (A) 50 NONINDUCTIVE 200 100 60 40 20 10 6 4 TJ = 25 2 1 .1 .2 .4 1.0 2 4 10 20 40 100 REVERSE VOLTAGE, ( V ) ) Mounting Pad Layout .052 (1.32)REF .035 (0.9)REF .033 (0.85)REF .044 (1.12)REF .150 (3.8)REF Dimensions in inches and (millimeters) .033 (0.85)REF DISCLAIMER NOTICE Rectron Inc reserves the right to make changes without notice to any product specification herein, to make corrections, modifications, enhancements or other changes. Rectron Inc or anyone on its behalf assumes no responsibility or liability for any errors or inaccuracies. Data sheet specifications and its information contained are intended to provide a product description only. "Typical" parameters which may be included on RECTRON data sheets and/ or specifications can and do vary in different applications and actual performance may vary over time. Rectron Inc does not assume any liability arising out of the application or use of any product or circuit. Rectron products are not designed, intended or authorized for use in medical, life-saving implant or other applications intended for life-sustaining or other related applications where a failure or malfunction of component or circuitry may directly or indirectly cause injury or threaten a life without expressed written approval of Rectron Inc. Customers using or selling Rectron components for use in such applications do so at their own risk and shall agree to fully indemnify Rectron Inc and its subsidiaries harmless against all claims, damages and expenditures.