MAXIM MAX9234_12

MAX9234/MAX9236/
MAX9238
Hot-Swappable, 21-Bit, DC-Balanced LVDS
Deserializers
General Description
The MAX9234/MAX9236/MAX9238 deserialize three
LVDS serial-data inputs into 21 single-ended
LVCMOS/LVTTL outputs. A parallel-rate LVDS clock
received with the LVDS data streams provides timing for
deserialization. The outputs have a separate supply,
allowing 1.8V to 5V output logic levels. All these devices
are hot-swappable and allow “on-the-fly” frequency
programming.
The MAX9234/MAX9236/MAX9238 feature DC balance,
which allows isolation between a serializer and deserializer using AC-coupling. Each deserializer decodes
data transmitted by one of the MAX9209/MAX9211/
MAX9213/MAX9215 serializers.
The MAX9234 has a rising-edge output strobe. The
MAX9236/MAX9238 have a falling-edge output strobe.
The MAX9234/MAX9236/MAX9238 operate in DCbalanced mode only.
The MAX9234/MAX9236 operate with a parallel input
clock of 8MHz to 34MHz, while the MAX9238 operates
from 16MHz to 66MHz. The transition time of the singleended outputs is increased on the low-frequency version
parts (MAX9234/MAX9236) for reduced EMI. The LVDS
inputs meet ISO 10605 ESD specification, ±25kV for AirGap Discharge and ±8kV Contact Discharge.
The MAX9234/MAX9236/MAX9238 are available in 48-pin
TSSOP packages and operate over the -40°C to +85°C
temperature range.
Features
o DC Balance Allows AC-Coupling for Wider Input
Common-Mode Voltage Range
o On-the-Fly Frequency Programming
o Operating Frequency Range
8MHz to 34MHz (MAX9234/MAX9236)
16MHz to 66MHz (MAX9238)
o Falling-Edge Output Strobe (MAX9236/MAX9238)
o Slower Output Transitions for Reduced EMI
(MAX9234/MAX9236)
o High-Impedance Outputs when PWRDWN Is Low
Allow Output Busing
o 5V-Tolerant PWRDWN Input
o PLL Requires No External Components
o Up to 1.386Gbps Throughput
o Separate Output Supply Pins Allow Interface to
1.8V, 2.5V, 3.3V, and 5V Logic
o LVDS Inputs Meet ISO 10605 ESD Requirements
o LVDS Inputs Conform to ANSI TIA/EIA-644 LVDS
Standard
o Low-Profile, 48-Lead TSSOP Package
o +3.3V Main Power Supply
o -40°C to +85°C Operating Temperature Range
Applications
Ordering Information
Automotive Navigation Systems
Automotive DVD Entertainment Systems
PART
TEMP RANGE
PINPACKAGE
-40°C to +85°C
48 TSSOP
Digital Copiers
Laser Printers
MAX9234EUM+
MAX9234EUM/V+
-40°C to +85°C
48 TSSOP
MAX9236EUM+
-40°C to +85°C
48 TSSOP
MAX9238EUM+
-40°C to +85°C
48 TSSOP
+Denotes a lead(Pb)-free/RoHS-compliant package.
/V Denotes an automotive qualified part.
Note: Devices are also available in a tape-and-reel packaging.
Specify tape and reel by adding “T” to the part number when
ordering.
Functional Diagram and Pin Configuration appear at end of
data sheet.
For pricing, delivery, and ordering information, please contact Maxim Direct
at 1-888-629-4642, or visit Maxim’s website at www.maximintegrated.com.
19-3641; Rev 2; 9/12
MAX9234/MAX9236/MAX9238
Hot-Swappable, 21-Bit, DC-Balanced LVDS
Deserializers
ABSOLUTE MAXIMUM RATINGS
VCC to GND ...........................................................-0.5V to +4.0V
VCCO to GND.........................................................-0.5V to +6.0V
RxIN_, RxCLK IN_ to GND ....................................-0.5V to +4.0V
PWRDWN to GND....................................................-0.5V to 6.0V
RxOUT_, RxCLK OUT to GND ................-0.5V to (VCCO + 0.5V)
Continuous Power Dissipation (TA = +70°C)
48-Pin TSSOP (derate 16mW/°C above +70°C) ....... 1282mW
Storage Temperature Range .............................-65°C to +150°C
Junction Temperature ......................................................+150°C
ESD Protection
Human Body Model (RD = 1.5kΩ, CS = 100pF)
All Pins to GND ..................................………………….±5kV
IEC 61000-4-2 (RD = 330Ω, CS = 150pF)
Contact Discharge (RxIN_, RxCLK IN_) to GND .........±8kV
Air-Gap Discharge (RxIN_, RxCLK IN_) to GND .......±15kV
ISO 10605 (RD = 2kΩ, CS = 330pF)
Contact Discharge (RxIN_, RxCLK IN_) to GND ........±8kV
Air Discharge (RxIN_, RxCLK IN_) to GND ...............±25kV
Lead Temperature (soldering, 10s) .................................+300°C
Soldering Temperature (reflow) .......................................+260°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
DC ELECTRICAL CHARACTERISTICS
(VCC = +3.0V to +3.6V, VCCO = +3.0V to +5.5V, PWRDWN = high, differential input voltage ⏐VID⏐ = 0.05V to 1.2V, input commonmode voltage VCM = ⏐VID/2⏐ to 2.4V - ⏐VID/2⏐, TA = -40°C to +85°C, unless otherwise noted. Typical values are at VCC = VCCO =
+3.3V, ⏐VID⏐ = 0.2V, VCM = 1.25V, TA = +25°C.) (Notes 1, 2)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
SINGLE-ENDED INPUT (PWRDWN)
High-Level Input Voltage
VIH
2.0
5.5
V
Low-Level Input Voltage
VIL
-0.3
+0.8
V
-70
+70
µA
-1.5
V
Input Current
Input Clamp Voltage
IIN
VCL
VIN = high or low
ICL = -18mA
SINGLE-ENDED OUTPUTS (RxOUT_, RxCLK OUT)
VCCO 0.1
IOH = -100µA
High-Level Output Voltage
RxCLK OUT
VCCO 0.25
RxOUT_
VCCO 0.40
MAX9234/
MAX9236
VOH
IOH = -2mA
V
VCCO 0.25
MAX9238
IOL = 100µA
Low-Level Output Voltage
VOL
IOL = 2mA
0.1
MAX9234/
MAX9236
RxCLK OUT
0.2
RxOUT_
0.26
MAX9238
High-Impedance Output Current
Output Short-Circuit Current
(Note: Short one output at a
time.)
2
IOZ
IOS
0.2
PWRDWN = low,
VOUT_ = -0.3V to VCCO + 0.3V
MAX9234/
VCCO = 3.0V to MAX9236
3.6V, VOUT = 0V
MAX9238
VCCO = 4.5V to
5.5V, VOUT = 0V
MAX9234/
MAX9236
MAX9238
V
-20
+20
RxCLK OUT
-10
-40
RxOUT_
-5
-20
-10
-40
RxCLK OUT
-28
-75
RxOUT_
-14
-37
-28
-75
µA
mA
Maxim Integrated
MAX9234/MAX9236/MAX9238
Hot-Swappable, 21-Bit, DC-Balanced LVDS
Deserializers
DC ELECTRICAL CHARACTERISTICS (continued)
(VCC = +3.0V to +3.6V, VCCO = +3.0V to +5.5V, PWRDWN = high, differential input voltage ⏐VID⏐ = 0.05V to 1.2V, input commonmode voltage VCM = ⏐VID/2⏐ to 2.4V - ⏐VID/2⏐, TA = -40°C to +85°C, unless otherwise noted. Typical values are at VCC = VCCO =
+3.3V, ⏐VID⏐ = 0.2V, VCM = 1.25V, TA = +25°C.) (Notes 1, 2)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
50
mV
LVDS INPUTS
Differential Input-High Threshold
VTH
Differential Input-Low Threshold
VTL
Input Current
Power-Off Input Current
Input Resistor 1
IIN+, IIN-
-50
PWRDWN = high or low
VCC = VCCO = 0V or open,
IINO+, IINOPWRDWN = 0V or open
RIN1
PWRDWN = high or low (Figure 1)
VCC = VCCO = 0V or open (Figure 1)
mV
-25
+25
µA
-40
+40
µA
42
78
kΩ
POWER SUPPLY
Worst-Case Supply Current
Power-Down Supply Current
Maxim Integrated
ICCW
ICCZ
CL = 8pF,
worst-case
pattern; VCC =
VCCO = 3.0V to
3.6V, Figure 2
PWRDWN = low
MAX9234/
MAX9236
MAX9238
8MHz
42
16MHz
57
34MHz
98
16MHz
63
34MHz
106
66MHz
177
50
mA
µA
3
MAX9234/MAX9236/MAX9238
Hot-Swappable, 21-Bit, DC-Balanced LVDS
Deserializers
AC ELECTRICAL CHARACTERISTICS
(VCC = VCCO = +3.0V to +3.6V, 100mVP-P at 200kHz supply noise, CL = 8pF, PWRDWN = high, differential input voltage ⏐VID⏐ =
0.1V to 1.2V, input common mode voltage VCM = ⏐VID/2⏐ to 2.4V - ⏐VID/2⏐, TA = -40°C to +85°C, unless otherwise noted. Typical
values are at VCC = VCCO = +3.3V, ⏐VID⏐ = 0.2V, VCM = 1.25V, TA = +25°C.) (Notes 3, 4, 5)
PARAMETER
Output Rise Time
Output Fall Time
RxIN Skew Margin
SYMBOL
CLHT
CHLT
RSKM
CONDITIONS
0.1VCCO to
0.9VCCO,
Figure 3
0.9VCCO to
0.1VCCO,
Figure 3
MAX9234/
MAX9236
MIN
TYP
MAX
RxOUT
3.52
5.04
6.24
RxCLK OUT
2.2
3.15
3.9
2.2
3.15
3.9
RxOUT
1.95
3.18
4.35
RxCLK OUT
1.3
2.12
2.9
1.3
2.12
2.9
8MHz
6600
7044
16MHz
2560
3137
34MHz
900
1327
66MHz
330
685
MAX9238
MAX9234/
MAX9236
MAX9238
Figure 4
(Note 6)
MAX9238
UNITS
ns
ns
ps
RxCLK OUT High Time
RCOH
Figures 5a, 5b
0.35 x
RCOP
ns
RxCLK OUT Low Time
RCOL
Figures 5a, 5b
0.35 x
RCOP
ns
RxOUT Setup to RxCLK OUT
RSRC
Figures 5a, 5b
0.30 x
RCOP
ns
RxOUT Hold from RxCLK OUT
RHRC
Figures 5a, 5b
0.45 x
RCOP
ns
RxCLK IN to RxCLK OUT Delay
RCCD
Figures 6a, 6b
4.9
Deserializer Phase-Locked Loop
Set
RPLLS
Deserializer Power-Down Delay
RPDD
6.17
8.1
ns
Figure 7
32800
x RCIP
ns
Figure 8
100
ns
Note 1: Current into a pin is defined as positive. Current out of a pin is defined as negative. All voltages are referenced to ground
except VTH and VTL.
Note 2: Maximum and minimum limits overtemperature are guaranteed by design and characterization. Devices are production
tested at TA = +25°C.
Note 3: AC parameters are guaranteed by design and characterization, and are not production tested. Limits are set at ±6 sigma.
Note 4: CL includes probe and test jig capacitance.
Note 5: RCIP is the period of RxCLK IN. RCOP is the period of RxCLK OUT. RCIP = RCOP.
Note 6: RSKM measured with ≤ 150ps cycle-to-cycle jitter on RxCLK IN.
4
Maxim Integrated
MAX9234/MAX9236/MAX9238
Hot-Swappable, 21-Bit, DC-Balanced LVDS
Deserializers
Typical Operating Characteristics
(VCC = VCCO = +3.3V, CL = 8pF, PWRDWN = high, differential input voltage ⏐VID⏐ = 0.2V, input common-mode voltage VCM = 1.2V,
TA = +25°C, unless otherwise noted.)
MAX9234/MAX9236
WORST-CASE PATTERN AND PRBS
SUPPLY CURRENT vs. FREQUENCY
MAX9238
WORST-CASE PATTERN AND PRBS
SUPPLY CURRENT vs. FREQUENCY
80
WORST CASE
70
60
27 - 1 PRBS
50
140
100
27 - 1 PRBS
80
60
30
40
5
10
15
20
25
35
30
40
10
20
30
40
50
60
70
FREQUENCY (MHz)
FREQUENCY (MHz)
MAX9234/MAX9236
RxOUT TRANSITION TIME
vs. OUTPUT SUPPLY VOLTAGE (VCCO)
MAX9238
RxOUT TRANSITION TIME
vs. OUTPUT SUPPLY VOLTAGE (VCCO)
6
CLHT
5
4
CHLT
3
2
5
OUTPUT TRANSITION TIME (ns)
MAX9234/6/8 toc03
7
OUTPUT TRANSITION TIME (ns)
WORST CASE
120
40
4
CLHT
3
2
CHLT
1
0
1
2.5
3.0
3.5
4.0
4.5
OUTPUT SUPPLY VOLTAGE (V)
Maxim Integrated
MAX9234/6/8 toc02
160
MAX9234/6/8 toc04
SUPPLY CURRENT (mA)
90
180
SUPPLY CURRENT (mA)
MAX9234/6/8 toc01
100
5.0
2.5
3.0
3.5
4.0
4.5
5.0
OUTPUT SUPPLY VOLTAGE (V)
5
MAX9234/MAX9236/MAX9238
Hot-Swappable, 21-Bit, DC-Balanced LVDS
Deserializers
Pin Description
PIN
1, 2, 4, 5, 45,
46, 47
FUNCTION
RxOUT14–RxOUT20 Channel 2 Single-Ended Outputs
3, 25, 32, 38,
44
GND
Ground
6
N.C.
No Connection
7, 13, 18
LVDS GND
8
RxIN0-
Inverting Channel 0 LVDS Serial-Data Input
9
RxIN0+
Noninverting Channel 0 LVDS Serial-Data Input
10
RxIN1-
Inverting Channel 1 LVDS Serial-Data Input
11
RxIN1+
Noninverting Channel 1 LVDS Serial-Data Input
12
LVDS VCC
LVDS Ground
LVDS Supply Voltage. Bypass to LVDS GND with 0.1µF and 0.001µF capacitors in parallel as
close to LVDS VCC as possible, with the smallest value capacitor closest to the supply pin.
14
RxIN2-
Inverting Channel 2 LVDS Serial-Data Input
15
RxIN2+
Noninverting Channel 2 LVDS Serial-Data Input
16
RxCLK IN-
Inverting LVDS Parallel Rate Clock Input
17
RxCLK IN+
Noninverting LVDS Parallel Rate Clock Input
19, 21
PLL GND
PLL Ground
20
PLL VCC
PLL Supply Voltage. Bypass to PLL GND with 0.1µF and 0.001µF capacitors in parallel as
close to PLL VCC as possible, with the smallest value capacitor closest to the supply pin.
22
PWRDWN
23
RxCLK OUT
24, 26, 27, 29,
30, 31, 33
RxOUT0–RxOUT6
28, 36, 48
VCCO
34, 35, 37, 39,
40, 41, 43
42
6
NAME
5V Tolerant LVTTL/LVCMOS Power-Down Input. Internally pulled down to GND. Outputs are
high impedance when PWRDWN = low or open.
Parallel Rate Clock Single-Ended Output. The MAX9234 has a rising-edge strobe. The
MAX9236/MAX9238 have a falling-edge strobe.
Channel 0 Single-Ended Outputs
Output Supply Voltage. Bypass to GND with 0.1µF and 0.001µF capacitors in parallel as
close to VCCO as possible, with the smallest value capacitor closest to the supply pin.
RxOUT7–RxOUT13 Channel 1 Single-Ended Outputs
VCC
Digital Supply Voltage. Bypass to GND with 0.1µF and 0.001µF capacitors in parallel as close
to VCC as possible, with the smallest value capacitor closest to the supply pin.
Maxim Integrated
MAX9234/MAX9236/MAX9238
Hot-Swappable, 21-Bit, DC-Balanced LVDS
Deserializers
Table 1. Part Equivalent Table
PART
EQUIVALENT WITH DCB/NC = HIGH OR OPEN
OPERATING
FREQUENCY (MHz)
MAX9234
MAX9210
8 to 34
Rising edge
MAX9236
MAX9220
8 to 34
Falling edge
MAX9238
MAX9222
16 to 66
Falling edge
Detailed Description
The MAX9234/MAX9236 operate at a parallel clock frequency of 8MHz to 34MHz. The MAX9238 operates at a
parallel clock frequency of 16MHz to 66MHz. The transition times of the single-ended outputs are increased
on the MAX9234/MAX9236 for reduced EMI.
DC Balance
Data coding by the MAX9209/MAX9211/MAX9213/
MAX9215 serializers (which are companion devices to
the MAX9234/MAX9236/MAX9238 deserializers) limits
the imbalance of ones and zeros transmitted on each
channel. If +1 is assigned to each binary 1 transmitted
and -1 is assigned to each binary 0 transmitted, the variation in the running sum of assigned values is called the
digital sum variation (DSV). The maximum DSV for the
data channels is 10. At most, 10 more zeros than ones,
or 10 more ones than zeros, are transmitted. The maximum DSV for the clock channel is five. Limiting the DSV
and choosing the correct coupling capacitors maintains
differential signal amplitude and reduces jitter due to
droop on AC-coupled links.
To obtain DC balance on the data channels, the serializer parallel data is inverted or not inverted, depending
on the sign of the digital sum at the word boundary.
Two complementary bits are appended to each group
of 7 parallel input data bits to indicate to the MAX9234/
MAX9236/MAX9238 deserializers whether the data bits
are inverted (see Figure 9). The deserializer restores
the original state of the parallel data. The LVDS clock
signal alternates duty cycles of 4/9 and 5/9, which
maintain DC balance.
AC-Coupling Benefits
Bit errors experienced with DC-coupling can be eliminated by increasing the receiver common-mode voltage
range by AC-coupling. AC-coupling increases the common-mode voltage range of an LVDS receiver to nearly
the voltage rating of the capacitor. The typical LVDS driver output is 350mV centered on an offset voltage of
1.25V, making single-ended output voltages of 1.425V
and 1.075V. An LVDS receiver accepts signals from 0 to
2.4V, allowing approximately ±1V common-mode difference between the driver and receiver on a DC-coupled
Maxim Integrated
OUTPUT STROBE
link (2.4V - 1.425V = 0.975V and 1.075V - 0V = 1.075V).
Common-mode voltage differences may be due to
ground potential variation or common-mode noise. If
there is more than ±1V of difference, the receiver is not
guaranteed to read the input signal correctly and may
cause bit errors. AC-coupling filters low-frequency
ground shifts and common-mode noise and passes
high-frequency data. A common-mode voltage difference up to the voltage rating of the coupling capacitor
(minus half the differential swing) is tolerated. DC-balanced coding of the data is required to maintain the differential signal amplitude and limit jitter on an
AC-coupled link. A capacitor in series with each output
of the LVDS driver is sufficient for AC-coupling.
However, two capacitors—one at the serializer output
and one at the deserializer input—provide protection in
case either end of the cable is shorted to a high voltage.
RxIN_ + OR
RxCLK IN+
RIN1
1.2V
RIN1
RxIN_ - OR
RxCLK IN-
Figure 1. LVDS Input Circuit
RCIP
RxCLK OUT
ODD RxOUT
EVEN RxOUT
RISING-EDGE STROBE SHOWN.
Figure 2. Worst-Case Test Pattern
7
MAX9234/MAX9236/MAX9238
Hot-Swappable, 21-Bit, DC-Balanced LVDS
Deserializers
90%
RxOUT_ OR
RxCLK OUT
90%
10%
RxOUT_ OR
RxCLK OUT
10%
8pF
CLHT
CHLT
Figure 3. Output Load and Transition Times
IDEAL SERIAL BIT TIME
1.3V
RxCLK IN
VID = 0
RCCD
1.5V
1.1V
RSKM
RxCLK OUT
RSKM
IDEAL
MIN
IDEAL
Figure 6a. MAX9234 Clock-IN to Clock-OUT Delay
MAX
INTERNAL STROBE
+
RxCLK IN
Figure 4. LVDS Receiver Input Skew Margin
VID = 0
RCCD
RCIP
1.5V
RxCLK OUT
RxCLK OUT
2.0V
0.8V
0.8V
RCOL
RCOH
RSRC
RHRC
2.0V
0.8V
RxOUT_
2.0V
2.0V
Figure 6b. MAX9236/MAX9238 Clock-IN to Clock-OUT Delay
2.0V
0.8V
2V
Figure 5a. MAX9234 Output Setup/Hold and High/Low Times
PWRDWN
3V
RCIP
VCC
RPLLS
RxCLK OUT
2.0V
2.0V
0.8V
0.8V
RCOH
RSRC
RxOUT_
2.0V
0.8V
0.8V
RHRC
2.0V
0.8V
Figure 5b. MAX9236/MAX9238 Output Setup/Hold and High/Low
Times
8
RxCLK IN
RCOL
RxCLK OUT
HIGH-Z
Figure 7. Phase-Locked Loop Set Time
Maxim Integrated
MAX9234/MAX9236/MAX9238
Hot-Swappable, 21-Bit, DC-Balanced LVDS
Deserializers
Applications Information
PWRDWN
Selection of AC-Coupling Capacitors
Voltage droop and the DSV of transmitted symbols
cause signal transitions to start from different voltage
levels. Because the transition time is finite, starting the
signal transition from different voltage levels causes
timing jitter. The time constant for an AC-coupled link
needs to be chosen to reduce droop and jitter to an
acceptable level.
0.8V
RxCLK IN
RPDD
RxOUT_
RxCLK OUT
HIGH-Z
Figure 8. Power-Down Delay
MAX9234/MAX9236/MAX9238 vs.
MAX9210/MAX9220/MAX9222
The MAX9234/MAX9236/MAX9238 operate in DC-balance mode only. Pinouts are the same as the
MAX9210/MAX9220/MAX9222 except that pin 6 on the
MAX9234/MAX9236/MAX9238 is no connect (N.C.). DC
balance allows AC-coupling with series capacitors. The
MAX9234/MAX9236/MAX9238 are hot-swappable and
the input frequency can be changed on the fly, but otherwise the specifications and functionality are the same
as the MAX9210/MAX9220/MAX9222 operating in DCbalance mode. See Table 1.
The RC network for an AC-coupled link consists of the
LVDS receiver termination resistor (RT), the LVDS driver
output resistor (RO), and the series AC-coupling capacitors (C). The RC time constant for two equal-value
series capacitors is (C x (RT + RO)) / 2 (Figure 10). The
RC time constant for four equal-value series capacitors
is (C x (RT + RO)) / 4 (Figure 11).
RT is required to match the transmission line impedance (usually 100Ω) and RO is determined by the LVDS
driver design (the minimum differential output resistance of 78Ω for the MAX9209/MAX9211/MAX9213/
MAX9215 serializers is used in the following example).
This leaves the capacitor selection to change the system time constant.
+
RxCLK IN
CYCLE N - 1
DCA2
CYCLE N
CYCLE N + 1
DCB2
TxIN20
TxIN19
TxIN18
TxIN17
TxIN16
TxIN15
TxIN14
DCA2
DCB2
TxIN20
TxIN19
TxIN18
TxIN17
TxIN16
TxIN15
TxIN14
DCB1
TxIN13
TxIN12
TxIN11
TxIN10
TxIN9
TxIN8
TxIN7
DCA1
DCB1
TxIN13
TxIN12
TxIN11
TxIN10
TxIN9
TxIN8
TxIN7
DCB0
TxIN6
TxIN5
TxIN4
TxIN3
TxIN2
TxIN1
TxIN0
DCA0
DCB0
TxIN6
TxIN5
TxIN4
TxIN3
TxIN2
TxIN1
TxIN0
RxIN2
DCA1
RxIN1
DCA0
RxIN0
TxIN_, DCA_, AND DCB_ ARE DATA FROM THE SERIALIZER.
Figure 9. Deserializer Serial Input
Maxim Integrated
9
MAX9234/MAX9236/MAX9238
Hot-Swappable, 21-Bit, DC-Balanced LVDS
Deserializers
MAX9209
MAX9211
MAX9213
MAX9215
HIGH-FREQUENCY, CERAMIC
SURFACE-MOUNT CAPACITORS
CAN ALSO BE PLACED AT THE
SERIALIZER INSTEAD OF THE DESERIALIZER.
TxOUT
MAX9234
MAX9236
MAX9238
RxIN
7
7
(7 + 2):1
100Ω
1:(9 - 2)
(7 + 2):1
100Ω
1:(9 - 2)
(7 + 2):1
100Ω
1:(9 - 2)
PLL
100Ω
PLL
7
7
TxIN
RxOUT
7
7
PWRDWN
PWRDWN
RxCLK OUT
TxCLK IN
TxCLK OUT
RxCLK IN
21:3 SERIALIZER
3:21 DESERIALIZER
Figure 10. Two Capacitors per Link, AC-Coupled
MAX9209
MAX9211
MAX9213
MAX9215
MAX9234
MAX9236
MAX9238
HIGH-FREQUENCY CERAMIC
SURFACE-MOUNT CAPACITORS
TxOUT
RxIN
7
7
(7 + 2):1
100Ω
1:(9 - 2)
(7 + 2):1
100Ω
1:(9 - 2)
(7 + 2):1
100Ω
1:(9 - 2)
PLL
100Ω
PLL
7
7
TxIN
RxOUT
7
7
PWRDWN
PWRDWN
RxCLK OUT
TxCLK IN
TxCLK OUT
21:3 SERIALIZER
RxCLK IN
3:21 DESERIALIZER
Figure 11. Four Capacitors per Link, AC-Coupled
10
Maxim Integrated
MAX9234/MAX9236/MAX9238
Hot-Swappable, 21-Bit, DC-Balanced LVDS
Deserializers
In the following example, the capacitor value for a
droop of 2% is calculated. Jitter due to this droop is
then calculated assuming a 1ns transition time:
C = - (2 x tB x DSV) / (ln (1 - D) x (RT + RO)) (Eq 1)
where:
C = AC-coupling capacitor (F).
tB = bit time (s).
DSV = digital sum variation (integer).
ln = natural log.
D = droop (% of signal amplitude).
RT = termination resistor (Ω).
RO = output resistance (Ω).
Equation 1 is for two series capacitors (Figure 10). The
bit time (tB) is the period of the parallel clock divided by
9. The DSV is 10. See equation 3 for four series capacitors (Figure 11).
The capacitor for 2% maximum droop at 8MHz parallel
rate clock is:
C = - (2 x tB x DSV) / (ln (1 - D) x (RT + RO))
C = - (2 x 13.9ns x 10) / (ln (1 - 0.02) x (100Ω + 78Ω))
C = 0.0773µF
Jitter due to droop is proportional to the droop and
transition time:
tJ = tT x D (Eq 2)
where:
tJ = jitter (s).
tT = transition time (s) (0 to 100%).
D = droop (% of signal amplitude).
Jitter due to 2% droop and assumed 1ns transition time is:
tJ = 1ns x 0.02
tJ = 20ps
The transition time in a real system depends on the frequency response of the cable driven by the serializer.
The capacitor value decreases for a higher frequency
parallel clock and for higher levels of droop and jitter.
Use high-frequency, surface-mount ceramic capacitors.
Equation 1 altered for four series capacitors (Figure 11) is:
C = - (4 x tB x DSV) / (ln (1 - D) x (RT + RO)) (Eq 3)
Input Bias and Frequency Detection
The inverting and noninverting LVDS inputs are internally
connected to +1.2V through 42kΩ (min) to provide biasing for AC-coupling (Figure 1). A frequency-detection
circuit on the clock input detects when the input is not
switching, or is switching at low frequency. In this case,
all outputs are driven low. To prevent switching due to
noise when the clock input is not driven, bias the clock
input to differential +15mV by connecting a 10kΩ ±1%
Maxim Integrated
pullup resistor between the noninverting input and VCC,
and a 10kΩ ±1% pulldown resistor between the inverting input and ground. These bias resistors, along with
the 100Ω ±1% tolerance termination resistor, provide
+15mV of differential input.
Unused LVDS Data Inputs
At each unused LVDS data input, pull the inverting input
up to VCC using a 10kΩ resistor, and pull the noninverting
input down to ground using a 10kΩ resistor. Do not connect a termination resistor. The pullup and pulldown resistors drive the corresponding outputs low and prevent
switching due to noise.
PWRDWN
Driving PWRDWN low puts the outputs in high impedance, stops the PLL, and reduces supply current to
50µA or less. Driving PWRDWN high drives the outputs
low until the PLL locks. The outputs of two deserializers
can be bused to form a 2:1 mux with the outputs controlled by PWRDWN. Wait 100ns between disabling one
deserializer (driving PWRDWN low) and enabling the
second one (driving PWRDWN high) to avoid contention of the bused outputs.
Input Clock and PLL Lock Time
There is no required timing sequence for the application or reapplication of the parallel rate clock (RxCLK
IN) relative to PWRDWN, or to a power-supply ramp for
proper PLL lock. The PLL lock time is set by an internal
counter. The maximum time to lock is 32,800 clock
periods. Power and clock should be stable to meet the
lock-time specification. When the PLL is locking, the
outputs are low.
Power-Supply Bypassing
There are separate on-chip power domains for digital
circuits, outputs, PLL, and LVDS inputs. Bypass each
VCC, VCCO, PLL VCC, and LVDS VCC pin with high-frequency, surface-mount ceramic 0.1µF and 0.001µF
capacitors in parallel as close to the device as possible, with the smallest value capacitor closest to the
supply pin.
Cables and Connectors
Interconnect for LVDS typically has a differential impedance of 100Ω. Use cables and connectors that have
matched differential impedance to minimize impedance
discontinuities.
Twisted-pair and shielded twisted-pair cables offer
superior signal quality compared to ribbon cable and
tend to generate less EMI due to magnetic field canceling effects. Balanced cables pick up noise as common
mode, which is rejected by the LVDS receiver.
11
MAX9234/MAX9236/MAX9238
Hot-Swappable, 21-Bit, DC-Balanced LVDS
Deserializers
Board Layout
Keep the LVTTL/LVCMOS outputs and LVDS input signals separated to prevent crosstalk. A four-layer PC
board with separate layers for power, ground, LVDS
inputs, and digital signals is recommended.
ESD Protection
The MAX9234/MAX9236/MAX9238 ESD tolerance is
rated for IEC 61000-4-2 Human Body Model and ISO
10605 standards. IEC 61000-4-2 and ISO 10605 specifiy
ESD tolerance for electronic systems. The Human Body
Model discharge components are CS = 100pF and RD =
1.5kΩ (Figure 12). For the Human Body Model, all pins
are rated for ±5kV contact discharge. The ISO 10605 discharge components are CS = 330pF and RD = 2kΩ
(Figure 13). For ISO 10605, the LVDS outputs are rated
for ±8kV contact and ±25kV air discharge. The IEC
61000-4-2 discharge components are CS = 150pF and
RD = 330Ω (Figure 14). For IEC 61000-4-2, the LVDS
inputs are rated for ±8kV Contact Discharge and ±15kV
Air-Gap Discharge.
5V Tolerant Input
PWRDWN is 5V tolerant and is internally pulled down to
GND.
R1
1MΩ
CHARGE-CURRENTLIMIT RESISTOR
HIGHVOLTAGE
DC
SOURCE
CS
100pF
R2
1.5kΩ
DISCHARGE
RESISTANCE
STORAGE
CAPACITOR
DEVICE
UNDER
TEST
Figure 12. Human Body ESD Test Circuit
R1
50Ω TO 100Ω
CHARGE-CURRENTLIMIT RESISTOR
HIGHVOLTAGE
DC
SOURCE
CS
330pF
R2
2kΩ
DISCHARGE
RESISTANCE
STORAGE
CAPACITOR
DEVICE
UNDER
TEST
Skew Margin (RSKM)
Skew margin (RSKM) is the time allowed for degradation of the serial data sampling setup and hold times by
sources other than the deserializer. The deserializer
sampling uncertainty is accounted for and does not
need to be subtracted from RSKM. The main outside
contributors of jitter and skew that subtract from RSKM
are interconnect intersymbol interference, serializer
pulse position uncertainty, and pair-to-pair path skew.
VCCO Output Supply and Power Dissipation
The outputs have a separate supply (VCCO) for interfacing
to systems with 1.8V to 5V nominal input-logic levels. The
DC Electrical Characteristics table gives the maximum
supply current for VCCO = 3.6V with 8pF load at several
switching frequencies with all outputs switching in the
worst-case switching pattern. The approximate incremental supply current for VCCO other than 3.6V with the same
8pF load and worst-case pattern can be calculated using:
II = CTVI 0.5fC x 21 (data outputs)
+ CTVIfC x 1 (clock output)
where:
II = incremental supply current.
CT = total internal (CINT) and external (CL) load capacitance.
VI = incremental supply voltage.
fC = output clock-switching frequency.
12
Figure 13. ISO 10605 Contact Discharge ESD Test Circuit
50Ω TO 100Ω
CHARGE-CURRENTLIMIT RESISTOR
HIGHVOLTAGE
DC
SOURCE
CS
150pF
RD
330Ω
DISCHARGE
RESISTANCE
STORAGE
CAPACITOR
DEVICE
UNDER
TEST
Figure 14. IEC 61000-4-2 Contact Discharge ESD Test Circuit
The incremental current is added to (for VCCO > 3.6V)
or subtracted from (for VCCO < 3.6V) the DC Electrical
Characteristics table maximum supply current. The
internal output buffer capacitance is CINT = 6pF. The
worst-case pattern-switching frequency of the data outputs is half the switching frequency of the output clock.
In the following example, the incremental supply current is
calculated for VCCO = 5.5V, fC = 34MHz, and CL = 8pF:
VI = 5.5V - 3.6V = 1.9V
CT = CINT + CL = 6pF + 8pF = 14pF
Maxim Integrated
MAX9234/MAX9236/MAX9238
Hot-Swappable, 21-Bit, DC-Balanced LVDS
Deserializers
where:
II = CTVI 0.5FC x 21 (data outputs) + CTVIfC x 1 (clock
output).
II = (14pF x 1.9V x 0.5 x 34MHz x 21) + (14pF x 1.9V x
34MHz).
the package power-dissipation rating. Do not exceed
the maximum package power-dissipation rating. See
the Absolute Maximum Ratings for maximum package
power-dissipation capacity and temperature derating.
II = 9.5mA + 0.9mA = 10.4mA.
The maximum supply current in DC-balanced mode for
VCC = VCCO = 3.6V at fC = 34MHz is 106mA (from the
DC Electrical Characteristics table). Add 10.4mA to get
the total approximate maximum supply current at VCCO
= 5.5V and VCC = 3.6V.
If the output supply voltage is less than VCCO = 3.6V,
the reduced supply current can be calculated using the
same formula and method.
At high switching frequency, high supply voltage, and
high capacitive loading, power dissipation can exceed
The MAX9234 has a rising-edge output strobe, which
latches the parallel output data into the next chip on the
rising edge of RxCLK OUT. The MAX9236/MAX9238
have a falling-edge output strobe, which latches the
parallel output data into the next chip on the falling
edge of RxCLK OUT. The deserializer output strobe
polarity does not need to match the serializer input
strobe polarity. A deserializer with rising- or fallingedge output strobe can be driven by a serializer with a
rising-edge input strobe.
Rising- or Falling-Edge Output Strobe
Functional Diagram
DATA
CHANNEL 0
LVDS DATA
RECEIVER 0
RxIN0+
STROBE
RxIN0-
RxIN1+
STROBE
SERIAL-TOPARALLEL
CONVERTER
RxIN2+
STROBE
SERIAL-TOPARALLEL
CONVERTER
LVDS CLOCK
RECEIVER
RxCLK IN+
RxCLK IN-
RxOUT7–13
DATA
CHANNEL 2
LVDS DATA
RECEIVER 2
RxIN2-
RxOUT0–6
DATA
CHANNEL 1
LVDS DATA
RECEIVER 1
RxIN1-
SERIAL-TOPARALLEL
CONVERTER
RxOUT14–20
RxCLK OUT
9x
PLL
REFERENCE
CLOCK
GENERATOR
PWRDWN
Maxim Integrated
13
MAX9234/MAX9236/MAX9238
Hot-Swappable, 21-Bit, DC-Balanced LVDS
Deserializers
Pin Configuration
Chip Information
PROCESS: CMOS
TOP VIEW
RxOUT17 1
+
48
VCCO
RxOUT18 2
47
RxOUT16
GND 3
46
RxOUT15
RxOUT19 4
45
RxOUT14
RxOUT20 5
44
GND
N.C. 6
43
RxOUT13
LVDS GND 7
42
VCC
RxIN0- 8
41
RxOUT12
40
RxOUT11
RxIN0+ 9
RxIN1- 10
MAX9234
MAX9236
MAX9238
39
RxOUT10
RxIN1+ 11
38
GND
RxOUT9
LVDS VCC 12
37
LVDS GND 13
36
VCCO
RxIN2- 14
35
RxOUT8
RxIN2+
15
34
RxOUT7
RxCLK IN-
16
33
RxOUT6
RxCLK IN+
17
32
GND
LVDS GND 18
31
RxOUT5
19
30
RxOUT4
PLL VCC 20
29
RxOUT3
PLL GND
21
28
VCCO
PWRDWN 22
27
RxOUT2
23
26
RxOUT1
RxOUT0 24
25
GND
PLL GND
RxCLK OUT
Package Information
For the latest package outline information and land patterns (footprints), go to www.maximintegrated.com/packages. Note that a
“+”, “#”, or “-” in the package code indicates RoHS status only.
Package drawings may show a different suffix character, but the
drawing pertains to the package regardless of RoHS status.
PACKAGE
TYPE
PACKAGE
CODE
OUTLINE NO.
LAND
PATTERN NO.
48 TSSOP
U48+1
21-0155
90-0124
TSSOP
14
Maxim Integrated
MAX9234/MAX9236/MAX9238
Hot-Swappable, 21-Bit, DC-Balanced LVDS
Deserializers
Revision History
REVISION
NUMBER
REVISION
DATE
0
4/05
Initial release
1
10/07
Added IEC 61000-4-2 ESD Performance; various style changes
2
9/12
Added the MAX9234EUM/V+ to Ordering Information
DESCRIPTION
PAGES
CHANGED
—
1, 2, 4, 5, 6, 12
1
Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent
licenses are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and
max limits) shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.
Maxim Integrated 160 Rio Robles, San Jose, CA 95134 USA 1-408-601-1000 ________________________________ 15
© 2012 Maxim Integrated Products, Inc.
Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc.