RFSW8006Q RFSW8006Q 11b/g/n/ac WiFi SP3T Switch In process of AEC-Q100 Qualification The RFSW8006Q is a single pole triple throw (SP3T) SOI switch in a 2x2mm, Pb-Free, 8-pin package. This switch is capable of switching between WiFi Rx, WiFi Tx, and Bluetooth Rx/Tx operations. The RFSW8006Q can also be placed in WiFi and Bluetooth modes simultaneously with a slight increase in insertion loss. This device meets or exceeds the RF switch needs of IEEE802.11b/g/n/ac WiFi RF systems. Package: DFN, 8-pin, 2.0mm x 2.0mm x 0.85mm Features ■ Symmetric SP3T Switch ■ Switch Control Voltage 1.2V to 4.8V ■ Low Insertion Loss 0.6dB (2.4GHz) ■ Isolation: 27dB (2.4GHz) ■ P0.1dB: 27dBm (3.6V) Applications VDD 1 ANT 2 8 7 RF2 CRF2 CRF1 3 6 CRF3 RF1 4 5 RF3 ■ Automotive WiFi ■ Automotive Data and Diagnostics ■ Infotainment ■ Key Fob ■ IEEE802.11b/g/n/ac WiFi Applications Functional Block Diagram Ordering Information RFSW8006QSQ Standard 25 piece bag RFSW8006QSR Standard 100 piece bag RFSW8006QTR7 Standard 2500 piece reel RFSW8006QPCK-410 Fully assembled evaluation board w/5 piece bag RF Micro Devices Inc. 7628 Thorndike Road, Greensboro, NC 27409-9421 For sales or technical support, contact RFMD at +1.336.678.5570 or [email protected]. ® DS150129 ® RF MICRO DEVICES and RFMD are trademarks of RFMD, LLC. BLUETOOTH is a trademark owned by Bluetooth SIG, Inc., U.S.A. and licensed for use by RFMD. All other trade names, trademarks, and registered trademarks are the property of their respective owners. ©2013, RF Micro Devices, Inc. 1 of 6 RFSW8006Q Absolute Maximum Ratings Parameter Supply Voltage Rating Unit 5 V ESD Human Body Model (HBM) 2000 V ESD Charged Device Model (CDM) 1000 V Operating Case Temperature -40 to +105 °C Storage Temperature -40 to +150 °C Moisture Sensitivity Level MSL2 Caution! ESD sensitive device. RFMD Green: RoHS status based on EU Directive 2011/65/EU (at time of this document revision), halogen free per IEC 61249-2-21, < 1000ppm each of antimony trioxide in polymeric materials and red phosphorus as a flame retardant, and <2% antimony in solder. Exceeding any one or a combination of the Absolute Maximum Rating conditions may cause permanent damage to the device. Extended application of Absolute Maximum Rating conditions to the device may reduce device reliability. Specified typical performance or functional operation of the device under Absolute Maximum Rating conditions is not implied. Nominal Operating Parameters Specification Parameter Unit Min Typ Condition Max Operating Parameters Operating Frequency Range 100 VDD 2.7 3.6 4000 MHz 4.8 V Switch Control Voltage: Low 0 0.20 V Switch Control Voltage: High 1.2 4.8 V VDD = 3.6V; CRF1 = 1.2V to 4.8V; T = -40°C to 105°C; 2412MHz to 2484MHz; Unless otherwise noted RF1 – ANT Insertion Loss 0.5 dB T = 25°C 0.6 1.2 dB All conditions Input Return Loss 20 15 dB Output Return Loss 20 15 dB RF1 to RF2 Isolation 25 30 dB Measured ANT - RF2 RF1 to RF3 Isolation 25 30 dB Measured ANT – RF3 VDD = 3.6V; CRF2 = 1.2V to 4.8V; T = -40°C to 85°C; 2412MHz to 2484MHz; Unless otherwise noted RF2 – ANT Insertion Loss 0.6 dB T = 25°C 0.6 1.2 dB T = 105°C Input Return Loss 20 15 dB Output Return Loss 20 15 dB RF2 to RF1 Isolation 23 25 dB Measured ANT - RF1 RF2 to RF3 Isolation 28 31 dB Measured ANT - RF3 VDD = 3.6V; CRF3 = 1.2V to 4.8V; T = -40°C to 85°C; 2412MHz to 2484MHz; Unless otherwise noted RF3 – ANT Insertion Loss 0.6 Input Return Loss Output Return Loss dB T = 25°C 0.6 1.2 dB T = 105°C 20 15 dB 20 15 dB RF3 to RF1 Isolation 23 26 dB Measured ANT – RF1 RF3 to RF2 Isolation 27 31 dB Measured ANT – RF2 RF Micro Devices Inc. 7628 Thorndike Road, Greensboro, NC 27409-9421 For sales or technical support, contact RFMD at +1.336.678.5570 or [email protected]. DS150129 The information in this publication is believed to be accurate. However, no responsibility is assumed by RF Micro Devices, Inc. ("RFMD") for its use, nor for any infringement of patents or other rights of third parties resulting from its use. No license is granted by implication or otherwise under any patent or patent rights of RFMD. RFMD reserves the right to change component circuitry, recommended application circuitry and specifications at any time without prior notice. 2 of 6 RFSW8006Q Specification Parameter Unit Min Typ Condition Max All Modes = CRF1 or CRF2 or CRF3; T = -40°C to 105°C; Unless otherwise noted General Parameters Passband Ripple -0.2 IP0.1dB; CW 25 27 0.2 dBm dB All Modes; VDD = 2.7V; CW 26 28 dBm All Modes; VDD ≥ 3.6V; CW Switch Total Current (IDD) 50 100 uA All Modes; VDD 2.7-4.8V; Control voltage 1.2 to 4.8V; T = 25°C Switch Control Current; High State 0.5 1.5 uA All Modes; Control voltage 1.2 to 4.8V; T = 25°C Switch Control Current; Low State 0.05 0.1 uA All Modes; Control voltage ≤ 0.2V; T = 25°C Switch Time, 50% CTL to 90% RF 150 500 ns All Modes; Switch Control = 1.2V to 4.8V Switch Time, 50% CTL to 10% RF 150 500 ns VDD = 3.6V; CRF1 = 1.2V to 4.8V; T = -40°C to 105°C; Unless otherwise noted 300MHz to 450MHz Operation Insertion Loss 0.4 dB 0.4 0.5 dB Input Return Loss 20 15 dB Output Return Loss 20 15 dB T = 25°C Switch Control Logic Table Mode CRF1 CRF2 CRF3 Condition RF1 1 0 0 RF1 to ANT RF2 0 1 0 RF2 to ANT RF3 0 0 1 RF3 to ANT RF Micro Devices Inc. 7628 Thorndike Road, Greensboro, NC 27409-9421 For sales or technical support, contact RFMD at +1.336.678.5570 or [email protected]. DS150129 The information in this publication is believed to be accurate. However, no responsibility is assumed by RF Micro Devices, Inc. ("RFMD") for its use, nor for any infringement of patents or other rights of third parties resulting from its use. No license is granted by implication or otherwise under any patent or patent rights of RFMD. RFMD reserves the right to change component circuitry, recommended application circuitry and specifications at any time without prior notice. 3 of 6 RFSW8006Q Application Schematic VDD RF2 8 1 100pF ANT 7 CRF2 3 6 CRF3 4 5 2 GND 100pF CRF1 RF1 100pF RF Micro Devices Inc. 7628 Thorndike Road, Greensboro, NC 27409-9421 For sales or technical support, contact RFMD at +1.336.678.5570 or [email protected]. RF3 100pF DS150129 The information in this publication is believed to be accurate. However, no responsibility is assumed by RF Micro Devices, Inc. ("RFMD") for its use, nor for any infringement of patents or other rights of third parties resulting from its use. No license is granted by implication or otherwise under any patent or patent rights of RFMD. RFMD reserves the right to change component circuitry, recommended application circuitry and specifications at any time without prior notice. 4 of 6 RFSW8006Q Pin Out VDD 1 8 ANT 2 7 CRF2 CRF1 3 6 CRF3 RF1 4 5 RF3 RF2 Package Drawing RF Micro Devices Inc. 7628 Thorndike Road, Greensboro, NC 27409-9421 For sales or technical support, contact RFMD at +1.336.678.5570 or [email protected]. DS150129 The information in this publication is believed to be accurate. However, no responsibility is assumed by RF Micro Devices, Inc. ("RFMD") for its use, nor for any infringement of patents or other rights of third parties resulting from its use. No license is granted by implication or otherwise under any patent or patent rights of RFMD. RFMD reserves the right to change component circuitry, recommended application circuitry and specifications at any time without prior notice. 5 of 6 RFSW8006Q Pin Names and Descriptions Pin Name Description 1 VDD Drain Voltage Supply 2 ANT Antenna RF Port. External DC block required. 3 CRF1 Switch control to enable RF1 to ANT 4 RF1 RF port1. External DC block required. 5 RF3 RF port3. External DC block required. 6 CRF3 Switch control to enable RF3 to ANT 7 CRF2 Switch control to enable RF2 to ANT 8 RF2 RF port2. External DC block required. RF Micro Devices Inc. 7628 Thorndike Road, Greensboro, NC 27409-9421 For sales or technical support, contact RFMD at +1.336.678.5570 or [email protected]. DS150129 The information in this publication is believed to be accurate. However, no responsibility is assumed by RF Micro Devices, Inc. ("RFMD") for its use, nor for any infringement of patents or other rights of third parties resulting from its use. No license is granted by implication or otherwise under any patent or patent rights of RFMD. RFMD reserves the right to change component circuitry, recommended application circuitry and specifications at any time without prior notice. 6 of 6