规格书编号 SPEC NO : 产品 规 格书 SPECIFICATION CUSTOMER 客 户： PRODUCT 产 品： SAW FILTER MODEL NO 型 号： HDF110M4 SMD-21 PREPARED 编 制： CHECKED 审 核： APPROVED 批 准： D A T E 日 期： 2005-11-18 客户确认 CUSTOMER RECEIVED: 审核 CHECKED 批准 APPROVED 日期 DATE 无锡市好达电子有限公司 Shoulder Electronics Limited www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 1 of 9 SAW FILTER HDF110M4 SMD-21 更改历史记录 History Record 更改日期 Date www.shoulder.cn 规格书编号 Spec. No. 产品型号 Part No. 客户产品型号 Customer No. Tel:0755-82916880 Fax:0755-82916881 更改内容描述 Modify Content E-mail:[email protected] 备注 Remark Page 2 of 9 SAW FILTER HDF110M4 SMD-21 1. SCOPE This specification shall cover the characteristics of SAW filter With 110M used for IF applications. 2. ELECTRICAL SPECIFICATION DC Voltage VDC AC Voltage Vpp Operation temperature Storage temperature RF Power Dissipation Electronic Characteristics 0V 10V50Hz/60Hz -40℃ to +85℃ -45℃ to +85℃ 0dBm 2-1.Electrical characteristics Parameter Minimum Typical Maximum Unit Center Frequency Fc(between -3dB points) Insertion loss at 110.0 MHz (Including loss in matching elements) (Excluding losses due to matching) Bnd width B-3dB B-25dB (Sweep:number of point 801) B-40dB Group delay ripple(p-p) (1. 50 ohm Matching；2. Average factor >16) (3. Smoothing : On) Fc-250KHz~Fc+250KHz Fc-650KHz~Fc+650KHz Relative attenuation ( At Fc 0 dB) Fc …… Fc±0.20MHz Fc±0.20KHz …… Fc±0.30MHz Fc±5,±6,±7,±8,±9,±10 MHz 109.95 110.0 110.05 MHz 14 10 dB 940 12 8 980 1900 2800 2060 4000 KHz 30 300 100 400 0.4 1.0 0.8 1.5 dB 35 Temperature coefficient of frequency TCf www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 nsec. E-mail:[email protected] 47 -18 ppm/K Page 3 of 9 SAW FILTER HDF110M4 SMD-21 3. TEST CIRCUIT Actual matching values may vary due to PCB layout and parasitics 1. Passband and relative attenuation test circuit 2. Group delay ripple test circuit www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 4 of 9 SAW FILTER HDF110M4 SMD-21 3.1.Typical frequency response 4. DIMENSION www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 5 of 9 SAW FILTER HDF110M4 SMD-21 5. ENVIRONMENTAL CHARACTERISTICS 5-1 Temperature cycling Subject the device to a low temperature of -40℃ for 30 minutes. Following by a high temperature of +25℃ for 5 Minutes and a higher temperature of +85℃ for 30 Minutes. Then release the device into the room conditions for 1 to 2 hours prior to the measurement. It shall meet the specifications in 2-1. 5-2 Resistance to solder heat Submerge the device terminals into the solder bath at 260℃ ±5℃ for 10±1 sec. Then release the device into the room conditions for 4 hours. It shall meet the specifications in 2-1. 5-3 Solderability Submerge the device terminals into the solder bath at 245℃ ±5℃ for 5s, More than 95% area of the soldering pad must be covered with new solder. It shall meet the specifications in 2-1. 5-4 Mechanical shock Drop the device randomly onto the concrete floor from the height of 1 m 3 times. the filter shall fulfill the specifications in 2-1. 5-5 Vibration Subject the device to the vibration for 2 hour each in x,y and z axes with the amplitude of 1.5 mm at 10 to 55 hz. The filter shall fulfill the specifications in 2-1. 6. REMARK 6.1 Static voltage Static voltage between signal load & ground may cause deterioration &destruction of the component. Please avoid static voltage. 6.2 Ultrasonic cleaning Ultrasonic vibration may cause deterioration & destruction of the component. Please avoid ultrasonic cleaning 6.3 Soldering Only leads of component may be soldered. Please avoid soldering another part of component. 7. Packing 7.1 Dimensions (1) Carrier Tape: Figure 1 (2) Reel: Figure 2 (3) The product shall be packed properly not to be damaged during transportation and storage. www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 6 of 9 SAW FILTER HDF110M4 SMD-21 7.2 Reeling Quantity 1000 pcs/reel 7’’ 3000 pcs/reel 13’’ 7.3 Taping Structure (1) The tape shall be wound around the reel in the direction shown below. (2) Label Device Name User Product Name Quantity Lot No. (3) Leader part and vacant position specifications. 8. TAPE SPECIFICATIONS 8.1 Tensile Strength of Carrier Tape: 4.4N/mm width www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 7 of 9 SAW FILTER HDF110M4 SMD-21 8.2 Top Cover Tape Adhesion (See the below figure) (1) pull off angle: 0~15º (2) speed: 300mm/min. (3) force: 20~70g [Figure 1] Carrier Tape Dimensions [Unit:mm] W F E P0 P1 P2 D0 D1 t1 t2 A B 12.00 ±0.30 7.50 ±0.10 1.75 ±0.10 4.00 ±0.10 8.00 ±0.10 2.00 ±0.10 Ø1.50 Ø1.5 ±0.25 0.25 ±0.05 2.20 ±0.10 5.30 ±0.10 7.30 ±0.10 [Figure 2] www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 8 of 9 SAW FILTER HDF110M4 SMD-21 [Unit:mm] A B C D E W t r Ø330 ±1.0 Ø100 ±0.5 Ø13 ±0.5 Ø21 ±0.8 2 ±0.5 16.8 ±0.3 3 max. 1.0 max. 9. CAUTION 9-1. This is an electrostatic sensitive device. Please avoid static voltage during operation and storage. 9-2. Sudden change of temperature shall be avoided, deterioration lf the characteristics can occur. 9-3. Ultrasonic vibration may cause deterioration and destruction of the components .Please avoid ultrasonic cleaning. www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 9 of 9