产品规格书 SPECIFICATION

规格书编号
SPEC NO :
产品 规 格书
SPECIFICATION
CUSTOMER 客 户:
PRODUCT 产 品:
SAW RESONATOR
MODEL NO 型 号:
HDR868.35M SMD-6
PREPARED 编 制:
CHECKED 审 核:
APPROVED 批 准:
D A T E 日 期:
2006-5-11
客户确认 CUSTOMER RECEIVED:
审核 CHECKED
批准 APPROVED
日期 DATE
无锡市好达电子有限公司
Shoulder Electronics Limited
www.shoulder.cn
Tel:0755-82916880 Fax:0755-82916881
E-mail:[email protected]
Page 1 of 7
SAW RESONATOR
HDR868.35M
SMD-6
更改历史记录
History Record
更改日期
Date
www.shoulder.cn
规格书编号
Spec. No.
产品型号
Part No.
客户产品型号
Customer No.
Tel:0755-82916880 Fax:0755-82916881
更改内容描述
Modify Content
E-mail:[email protected]
备注
Remark
Page 2 of 7
SAW RESONATOR
HDR868.35M
SMD-6
1. SCOPE
This specification shall cover the characteristics of 1-port SAW resonator with 868.35M used
for remote-control security.
2. ELECTRICAL SPECIFICATION
DC Voltage VDC
AC Voltage Vpp
Operation temperature
Storage temperature
RF Power Dissipation
10V
10V50Hz/60Hz
-40℃ to +85℃
-45℃ to +85℃
0dBm
2.2 Electronic Characteristics
Item
Unites
Minimum
Typical
Maximum
Center Frequency
MHz
868.100
868.350
868.600
1.5
2.5
Insertion Loss
dB
Quality Factor Unload Q
10000
15000
50Ω Loaded Q
1000
2000
10
25
Temperature
Turnover Temperature
℃
Stability
Freq.temp.Coefficient
ppm/℃2
0.037
ppm/yr
<±10
Frequency Aging
DC. Insulation Resistance
RF Equivalent
RLC Model
MΩ
1.0
Motional Resistance R1
Ω
27
Motional Inductance L1
μH
25.582
Motional Capacitance C1
fF
1.3131
pF
1.67
Transducer Static Capacitance
40
30
3. TEST CIRCUIT
www.shoulder.cn
Tel:0755-82916880 Fax:0755-82916881
E-mail:[email protected]
Page 3 of 7
SAW RESONATOR
HDR868.35M
SMD-6
4. DIMENSION
B#,E#
Input/Output
A#,C#,F #,D#
Ground
5. ENVIRONMENTAL CHARACTERISTICS
5-1 High temperature exposure
Subject the device to +85℃ for 16 hours. Then release the resonator into the room
conditions for 24 hours prior to the measurement. It shall fulfill the specifications in 2.2.
5-2 Low temperature exposure
Subject the device to -40℃ for 16 hours. Then release the device into the room conditions
for 24 hours prior to the measurement. It shall fulfill the specifications in 2.2.
5-3 Temperature cycling
Subject the device to a low temperature of -40℃ for 30 minutes. Following by a high
temperature of +85℃ for 30 Minutes. Then release the device into the room conditions
for 24 hours prior to the measurement. It shall meet the specifications in 2.2.
5-4 Resistance to solder heat
Dip the device terminals no closer than 1.5mm into the solder bath at 260℃ ±10℃ for
10±1 sec. Then release the device into the room conditions for 4 hours. The device shall
meet the specifications in 2.2.
5-5 Solderability
Subject the device terminals into the solder bath at 245℃±5℃ for 5s, More than 95%
area of the terminals must be covered with new solder. It shall meet the specifications in
2.2.
5-6 Mechanical shock
Drop the device randomly onto the concrete floor from the height of 1m 3 times. the device
shall fulfill the specifications in 2.2.
5-7 Vibration
Subject the device to the vibration for 1 hour each in x,y and z axes with the amplitude of
1.5 mm at 10 to 55 Hz. The device shall fulfill the specifications in 2.2.
www.shoulder.cn
Tel:0755-82916880 Fax:0755-82916881
E-mail:[email protected]
Page 4 of 7
SAW RESONATOR
HDR868.35M
SMD-6
6. REMARK
6.1 Static voltage
Static voltage between signal load & ground may cause deterioration &destruction of the
component. Please avoid static voltage.
6.2 Ultrasonic cleaning
Ultrasonic vibration may cause deterioration & destruction of the component. Please
avoid ultrasonic cleaning
6.3 Soldering
Only leads of component may be soldered. Please avoid soldering another part of
component.
7. Packing
7.1 Dimensions
(1) Carrier Tape: Figure 1
(2) Reel: Figure 2
(3) The product shall be packed properly not to be damaged during transportation and storage.
7.2 Reeling Quantity
1000 pcs/reel 7’’
3000 pcs/reel 13’’
7.3 Taping Structure
(1) The tape shall be wound around the reel in the direction shown below.
(2) Label
Device Name
User Product Name
Quantity
Lot No.
www.shoulder.cn
Tel:0755-82916880 Fax:0755-82916881
E-mail:[email protected]
Page 5 of 7
SAW RESONATOR
HDR868.35M
SMD-6
(3) Leader part and vacant position specifications.
8. TAPE SPECIFICATIONS
8.1 Tensile Strength of Carrier Tape: 4.4N/mm width
8.2 Top Cover Tape Adhesion (See the below figure)
(1) pull off angle: 0~15º
(2) speed: 300mm/min.
(3) force: 20~70g
[Figure 1] Carrier Tape Dimensions
[Unit:mm]
www.shoulder.cn
Tel:0755-82916880 Fax:0755-82916881
E-mail:[email protected]
Page 6 of 7
SAW RESONATOR
HDR868.35M
SMD-6
W
F
E
P0
P1
P2
D0
D1
t1
t2
A
B
12.0
5.5
1.75
4.0
4.0
2.0
Ø1.5
Ø1.0
0.3
1.25
3.3±
3.3±
±0.3
±0.05
±0.1
±0.1
±0.1
±0.05
±0.1
±0.25
±0.05
±0.1
0.1
0.1
[Figure 2]
www.shoulder.cn
Tel:0755-82916880 Fax:0755-82916881
E-mail:[email protected]
Page 7 of 7