规格书编号 SPEC NO : 产品 规 格书 SPECIFICATION CUSTOMER 客 户： PRODUCT 产 品： SAW RESONATOR MODEL NO 型 号： HDR915M SMD-6 PREPARED 编 制： CHECKED 审 核： APPROVED 批 准： D A T E 日 期： 2006-5-11 客户确认 CUSTOMER RECEIVED: 审核 CHECKED 批准 APPROVED 日期 DATE 无锡市好达电子有限公司 Shoulder Electronics Limited www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 1 of 8 SAW RESONATOR HDR915M S6 更改历史记录 History Record 更改日期 Date www.shoulder.cn 规格书编号 Spec. No. 产品型号 Part No. 客户产品型号 Customer No. Tel:0755-82916880 Fax:0755-82916881 更改内容描述 Modify Content E-mail:[email protected] 备注 Remark Page 2 of 8 SAW RESONATOR HDR915M S6 This specification shall cover the characteristics of 1-port SAW resonator with 915MHz for remote-control security. used 1. SCOPE 2. ELECTRICAL SPECIFICATION DC Voltage VDC AC Voltage Vpp Operation temperature Storage temperature RF Power Dissipation 10V 10V50Hz/60Hz -40℃ to +85℃ -45℃ to +85℃ 0dBm 2.2Electronic Characteristics Item Unites Minimum Typical Maximum Center Frequency MHz 914.750 915.000 915.250 1.5 3.5 Insertion Loss dB Quality Factor Unload Q 8000 12800 50Ω Loaded Q 1000 2000 ℃ 10 Temperature Turnover Temperature Stability Turnover Frequency KHz fo±2.7 Freq.temp.Coefficient ppm/℃2 0.037 ppm/yr <±10 Frequency Aging DC. Insulation Resistance Motional Resistance R1 RF Equivalent Motional Inductance L1 RLC Model Motional Capacitance C1 Pin 1 to Pin 2 Staic Capacitance Transducer Static Capacitance MΩ 25 1.0 Ω 21.76 μH 17.298 fF 1.749 pF 40 2.7 pF 3.1 26 3.5 2.3 3. TEST CIRCUIT www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 3 of 8 SAW RESONATOR HDR915M S6 4. DIMENSION B#,E# Input/Output A#,C#,F #,D# Ground 5. ENVIRONMENTAL CHARACTERISTICS 5-1 High temperature exposure Subject the device to +85℃ for 16 hours. Then release the resonator into the room conditions for 24 hours prior to the measurement. It shall fulfill the specifications in 2.2. 5-2 Low temperature exposure Subject the device to -40℃ for 16 hours. Then release the device into the room conditions for 24 hours prior to the measurement. It shall fulfill the specifications in 2.2. 5-3 Temperature cycling Subject the device to a low temperature of -40℃ for 30 minutes. Following by a high temperature of +85℃ for 30 Minutes. Then release the device into the room conditions for 24 hours prior to the measurement. It shall meet the specifications in 2.2. 5-4 Resistance to solder heat Dip the device terminals no closer than 1.5mm into the solder bath at 260℃ ±10℃ for 10±1 sec. Then release the device into the room conditions for 4 hours. The device shall meet the specifications in 2.2. 5-5 Solderability Subject the device terminals into the solder bath at 245℃ ±5℃ for 5s, More than 95% area of the terminals must be covered with new solder. It shall meet the specifications in 2.2. 5-6 Mechanical shock Drop the device randomly onto the concrete floor from the height of 1m 3 times. the device shall fulfill the specifications in 2.2. 5-7 Vibration Subject the device to the vibration for 1 hour each in x,y and z axes with the amplitude of 1.5 mm at 10 to 55 Hz. The device shall fulfill the specifications in 2.2. www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 4 of 8 SAW RESONATOR HDR915M S6 6. REMARK 6.1 Static voltage Static voltage between signal load & ground may cause deterioration &destruction of the component. Please avoid static voltage. 6.2 Ultrasonic cleaning Ultrasonic vibration may cause deterioration & destruction of the component. Please avoid ultrasonic cleaning 6.3 Soldering Only leads of component may be soldered. Please avoid soldering another part of component. 7. Packing 7.1 Dimensions (1) Carrier Tape: Figure 1 (2) Reel: Figure 2 (3) The product shall be packed properly not to be damaged during transportation and storage. 7.2 Reeling Quantity 1000 pcs/reel 7’’ 3000 pcs/reel 13’’ 7.3 Taping Structure (1) The tape shall be wound around the reel in the direction shown below. (2) Label Device Name User Product Name Quantity www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 5 of 8 SAW RESONATOR HDR915M S6 Lot No. (3) Leader part and vacant position specifications. 8. TAPE SPECIFICATIONS 8.1 Tensile Strength of Carrier Tape: 4.4N/mm width 8.2 Top Cover Tape Adhesion (See the below figure) (1) pull off angle: 0~15º (2) speed: 300mm/min. (3) force: 20~70g [Figure 1] Carrier Tape Dimensions www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 6 of 8 SAW RESONATOR HDR915M S6 [Unit:mm] W F E P0 P1 P2 D0 D1 t1 t2 A B 12.0 5.5 1.75 4.0 4.0 2.0 Ø1.5 Ø1.0 0.3 1.25 3.3± 3.3± ±0.3 ±0.05 ±0.1 ±0.1 ±0.1 ±0.05 ±0.1 ±0.25 ±0.05 ±0.1 0.1 0.1 [Figure 2] www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 7 of 8 SAW RESONATOR www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 HDR915M E-mail:[email protected] S6 Page 8 of 8