产品规格书 SPECIFICATION

规格书编号
SPEC NO :
产品 规 格书
SPECIFICATION
CUSTOMER 客 户:
PRODUCT 产 品:
SAW FILTER
MODEL NO 型 号:
HDF204M SMD-21
PREPARED 编 制:
CHECKED 审 核:
APPROVED 批 准:
D A T E 日 期:
2007-7-16
客户确认 CUSTOMER RECEIVED:
审核 CHECKED
批准 APPROVED
日期 DATE
无锡市好达电子有限公司
Shoulder Electronics Limited
www.shoulder.cn
Tel:0755-82916880 Fax:0755-82916881
E-mail:[email protected]
Page 1 of 10
SAW FILTER
HDF204M
SMD-21
更改历史记录
History Record
更改日期
Date
www.shoulder.cn
规格书编号
Spec. No.
产品型号
Part No.
客户产品型号
Customer No.
Tel:0755-82916880 Fax:0755-82916881
更改内容描述
Modify Content
E-mail:[email protected]
备注
Remark
Page 2 of 10
SAW FILTER
HDF204M
SMD-21
1. SCOPE
This specification shall cover the characteristics of SAW filter With 204M used for IF
applications.
2. ELECTRICAL SPECIFICATION
DC Voltage VDC
AC Voltage Vpp
Operation temperature
Storage temperature
RF Power Dissipation
10V
10V50Hz/60Hz
-40℃ to +85℃
-45℃ to +85℃
0dBm
2.1Electrical characteristics
Parameter
Minimum
Optimal source Impedance(5)
Optimal Load Impedance(5)
Temperature coefficient of frequency
Maximum Unit
204
Center Frequency,Fo
Insertion loss at 204 MHz
Including losses in matching test
circuit show below
1 dB Lower Frequency
1 dB Upper frequency
Amplitude Variation
203.7~204.3 MHz
Group delay variation
203.7~204.3 MHz
Rejection(4)
194~200 MHz
200~201.5 MHz
201.5~202 MHz
206.0~206.5 MHz
206.5~209 MHz
209~214 MHz
Typical
204.3
MHz
10.5
12.0
203.56
204.43
203.8
0.6
1.2
26
170
36
36
35
35
38
38
38
38
38
35
43.5
46.4
8ohm//99nH
dB
MHz
dB
nsec.
dB
ohm
8ohm//99nH
ohm
+1.7
ppm/K
Notes:
1.All specifications are based on the test circuit shown below
2. This specification is valid for room temperature only
3.Electrical margin has been built into the design to account for the variations due to manufacturing tolerances
4.Relative to insertion loss at 204 MHz
www.shoulder.cn
Tel:0755-82916880 Fax:0755-82916881
E-mail:[email protected]
Page 3 of 10
SAW FILTER
HDF204M
SMD-21
5.This is the complex conjugate of the unmatched filter’s impedance resulting in maximum power reansfer
3.1 TEST CIRCUIT
Actual matching values may vary due to PCB layout and parasitics
3.2 Typical frequency response
www.shoulder.cn
Tel:0755-82916880 Fax:0755-82916881
E-mail:[email protected]
Page 4 of 10
SAW FILTER
www.shoulder.cn
Tel:0755-82916880 Fax:0755-82916881
HDF204M
E-mail:[email protected]
SMD-21
Page 5 of 10
SAW FILTER
HDF204M
SMD-21
4. DIMENSION
www.shoulder.cn
Tel:0755-82916880 Fax:0755-82916881
E-mail:[email protected]
Page 6 of 10
SAW FILTER
HDF204M
SMD-21
5. ENVIRONMENTAL CHARACTERISTICS
5-1 Temperature cycling
Subject the device to a low temperature of -40℃for 30 minutes. Following by a high
temperature of +25℃ for 5 Minutes and a higher temperature of +85℃ for 30 Minutes.
Then release the device into the room conditions for 1 to 2 hours prior to the measurement.
It shall meet the specifications in 2.1.
5-2 Resistance to solder heat
Submerge the device terminals into the solder bath at 260℃ ±5℃ for 10±1 sec.
Then release the device into the room conditions for 4 hours. It shall meet the specifications
in 2.1.
5-3 Solderability
Submerge the device terminals into the solder bath at 245℃ ±5℃ for 5s, More than
95% area of the soldering pad must be covered with new solder. It shall meet the
specifications in 2.1.
5-4 Mechanical shock
Drop the device randomly onto the concrete floor from the height of 1 m 3 times. the
filter shall fulfill the specifications in 2.1.
5-5 Vibration
Subject the device to the vibration for 2 hour each in x,y and z axes with the
amplitude of 1.5 mm at 10 to 55 hz. The filter shall fulfill the specifications in 2.1.
6. REMARK
6.1 Static voltage
Static voltage between signal load & ground may cause deterioration &destruction of
the component. Please avoid static voltage.
6.2 Ultrasonic cleaning
Ultrasonic vibration may cause deterioration & destruction of the component. Please
avoid ultrasonic cleaning
6.3 Soldering
Only leads of component may be soldered. Please avoid soldering another part of
component.
7. Packing
7.1 Dimensions
(1) Carrier Tape: Figure 1
(2) Reel: Figure 2
(3) The product shall be packed properly not to be damaged during transportation and storage.
7.2 Reeling Quantity
1000 pcs/reel 7’’
www.shoulder.cn
Tel:0755-82916880 Fax:0755-82916881
E-mail:[email protected]
Page 7 of 10
SAW FILTER
3000 pcs/reel
HDF204M
SMD-21
13’’
7.3 Taping Structure
(1) The tape shall be wound around the reel in the direction shown below.
(2) Label
Device Name
User Product Name
Quantity
Lot No.
(3) Leader part and vacant position specifications.
8. TAPE SPECIFICATIONS
8.1 Tensile Strength of Carrier Tape: 4.4N/mm width
8.2 Top Cover Tape Adhesion (See the below figure)
www.shoulder.cn
Tel:0755-82916880 Fax:0755-82916881
E-mail:[email protected]
Page 8 of 10
SAW FILTER
HDF204M
SMD-21
(1) pull off angle: 0~15º
(2) speed: 300mm/min.
(3) force: 20~70g
[Figure 1] Carrier Tape Dimensions
[Unit:mm]
W
F
E
P0
P1
P2
D0
D1
t1
t2
A
B
12.00
±0.30
7.50
±0.10
1.75
±0.10
4.00
±0.10
8.00
±0.10
2.00
±0.10
Ø1.50
Ø1.5
±0.25
0.25
±0.05
2.20
±0.10
5.80
±0.10
7.30
±0.10
[Figure 2]
www.shoulder.cn
Tel:0755-82916880 Fax:0755-82916881
E-mail:[email protected]
Page 9 of 10
SAW FILTER
HDF204M
SMD-21
[Unit:mm]
A
B
C
D
E
W
t
r
Ø330
±1.0
Ø100
±0.5
Ø13
±0.5
Ø21
±0.8
2
±0.5
16.8
±0.3
3
max.
1.0
max.
9. CAUTION
9-1. This is an electrostatic sensitive device. Please avoid static voltage during operation and
storage.
9-2. Sudden change of temperature shall be avoided , deterioration lf the characteristics can
occur.
9-3. Ultrasonic vibration may cause deterioration and destruction of the components Please avoid
ultrasonic cleaning.
www.shoulder.cn
Tel:0755-82916880 Fax:0755-82916881
E-mail:[email protected]
Page 10 of 10