- Soberton Inc.

SPECIFICATION
FOR
APPROVAL
Customer:
Description:
Magnetic Buzzer
Soberton Part No. : ST-03BL-1
Date:2015-02-26
Customer Model No. :
Date of Approval
Authorization
Signature
SOBERTON, INC.
211 N. First Street Minneapolis, MN. 55401
Tel:612-849-6205
Fax:952-922-3120
Http://www.soberton.com E-mail: [email protected]
Approved
Checked
Design
Jasmine
Frank
Jim
2015/2/26
2015/2/26
2015/2/26
CUSTOMER
MODEL NUMBER
NUMBER
ST-03BL-1
PRODUCT TYPE
REVISION
DATE
PAGE
Magnetic Buzzer
A
2015/2/26
2/6
A:SCOPE
This specification applies Magnetic Buzzer,
ST-03BL-1
B:SPECIFICATION
Item
No.
1 Oscillation Frequency
Unit
Specification
Condition
Hz
2300
Vo-p=1/2duty , square wave
2
Operating Voltage
Vo-p
2.5~4.5
3
Rated Voltage
Vo-p
3.6
4
Current Consumption
mA
MAX. 100
at Rated Voltage
5
Sound Pressure Level
dB
MIN. 87
at 10cm at Rated Voltage
6
Coil Resistance
Ω
16±3
7
Operating Temperature
℃
-20 ~ +70
8
Storage Temperature
℃
-30 ~ +80
9
Dimension
mm
8.5 x 8.5 x H3.0
10
Weight (MAX)
gram
0.8
11
Housing Material
LCP( Black )
12
Leading Pin
Tin Plated Brass(Sn)
13
Environmental
Protection Regulation
C.APPEARANCE DRAWING
Tol : ± 0.3
Unit: mm
RoHS
See appearance drawing
See appearance drawing
MODEL NUMBER
CUSTOMER
NUMBER
ST-03BL-1
PRODUCT TYPE
REVISION
DATE
PAGE
Magnetic Buzzer
A
2015-02-26
3/6
D.TESTING METHOD
Standard Measurement conditions
Temperature:25±2℃
Humidity:45-65%
Acoustic Characteristics:
The oscillation frequency, current consumption and sound pressure are measured by the
measuring instruments shown below
In the measuring test, buzzer is placed as follows:
E. Typical Frequency Response Curve
MODEL NUMBER
CUSTOMER
NUMBER
ST-03BL-1
PRODUCT TYPE
REVISION
DATE
PAGE
Magnetic Buzzer
A
2015-02-26
4/6
F. Recommend Driving Circuit
The base current Ib should high enough so that it saturates the collector current of the
transistor with the CB load.
G. Soldering Condition
(1)Recommendable reflow soldering condition is as follows
(Reflow soldering is twice)
Note:It is requested that reflow soldering should be executed
Heat resistant line
(Used when heat resistant reliability test is performed)
(2)Manual soldering
Manual soldering temperature 350º C within 5 sec.
CUSTOMER
MODEL NUMBER
NUMBER
ST-03BL-1
PRODUCT TYPE
REVISION
DATE
PAGE
Magnetic Buzzer
A
2015-02-26
5/6
H. RELIABILITY TEST
NO.
1
2
ITEM
High Temperature
Test (Storage)
Low Temperature
Test (Storage)
TEST CONDITION AND REQUIREMENT
After being placed in a chamber with 80±2ºC for 96 hours and then
being placed in normal condition for 2 hours.
Allowable variation of SPL after test: ±10dB.
After being Placed in a chamber with -30±2ºC for 96 hours and then
being placed in normal condition for 2 hours.
Allowable variation of SPL after test: ±10dB.
After being Placed in a chamber with 90-95% R.H. at 40±2ºC for 96
3
Humidity Test
hours and then being placed in normal condition for 2 hours.
Allowable variation of SPL after test: ±10dB.
The part shall be subjected to 5 cycles. One cycle shall be consist of:
+70ºC
+25ºC
4
+25ºC
Temperature Cycle
Test
20ºC
Allowable variation of SPL after test: ±10dB.
Drop on a hard wood board of 4cm thick, any directions ,6 times,
5
Drop Test
at the height of 75cm .
Allowable variation of SPL after test: ±10dB.
After being applied vibration of amplitude of 1.5mm with 10 to 55 Hz
6
Vibration Test
band of vibration frequency to each of 3 perpendicular directions for
2 hours .
Allowable variation of SPL after test: ±10dB.
Lead terminals are immersed in rosin for 5 seconds and then
7
Solderability
Test
immersed in solder bath of +300±5ºC for 3±1 seconds .
90% min. lead terminals shall be wet with solder
(Except the edge of terminals).
8
Terminal Strength
Pulling Test
The force of 9.8N(1.0kg) is applied to each terminal in axial direction for
10 seconds.
No visible damage and cutting off.
TEST CONDITION.
Standard Test Condition
: a) Temperature : +5 ~ +35℃
b) Humidity : 45-85%
c) Pressure :
860-1060mbar
a) +5 ~ +35℃
b) 45-85%
c) 860-1060mbar
Judgment Test Condition: a) Temperature : +25 ± 2℃
b) Humidity : 60-70%
c) Pressure : 860-1060mbar
a) +25 ± 2℃
b) 60-70%
c) 860-1060mbar
MODEL NUMBER
CUSTOMER
NUMBER
ST-03BL-1
I.
PRODUCT TYPE
REVISION
DATE
PAGE
Magnetic Buzzer
A
2015-02-26
6/6
PACKING STANDARD
1 Reel : 1000PCS
Carton Box
(10 Inner Box)
Inner Box
(1Layer Reel)
Inner Box
330mmx330mmx30mm
1x1000PCS=1000PCS
Carton Box
350mmx350mmx370mm
10x1000PCS=10,000PCS